| Age | Commit message (Collapse) | Author |
|---|
|
Factor out common code from the uniphier SD driver, change the prefix
of the functions from uniphier_sd_ to matsu_sd_ and create separate
renesas-sdhi.c driver. Thus far, all the code is still compiled when
CONFIG_UNIPHIER_MMC is selected and there is no functional change.
This patch is a preparation for further split of the SoC specific
parts of the Matsushita SD driver, used both on Uniphier and R-Car.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Enable the HUSH shell, since it is far more capable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Skip the cache initialization, which can be done later on in U-Boot
proper, since this interferes with early DRAM initialization in TPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Pull the SPL code from porter.c into a separate file in
preparation for the addition of system initialization code.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add TPL config symbols for RAM loading matching the SPL ones.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
This patch is a preparation for adding TPL support for RAM loading.
CONFIG_IS_ENABLED allows for proper handling of the U-Boot/SPL/TPL
differences in config symbol names.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
The tiny variants of memset and memcpy implementations can be
built for TPL as well, check whether a TPL build is in progress
and avoid including the default variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
This patch fixes a situation where CONFIG_DM_SERIAL is enabled for
regular U-Boot and SPL, but not for TPL. In that case, the build
will try to include serial-uclass into the TPL nonetheless, because
CONFIG_DM_SERIAL is set.
The solution is to check if the build is for SPL or TPL and in that
case, check if CONFIG_$(SPL_TPL_)DM_SERIAL is also set. Only in that
case, include serial-uclass.c . If the build is for regular U-Boot,
CONFIG_BUILD is not set, so only check if CONFIG_DM_SERIAL is set
and if so, include serial-uclass.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
Add Kconfig entry for CONFIG_TPL_YMODEM_SUPPORT symbol to match the SPL one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
Add Kconfig entry for CONFIG_TPL_SPI_LOAD symbol to match the SPL one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
|
|
The mutex lock and unlock functions are stubbed out and mutex_is_locked
was 0. This caused asserts to fail in ubifs code when checking that the
mutex was locked. For example,
UBIFS assert failed in ubifs_change_lp at 540
UBIFS assert failed in ubifs_release_lprops at 278
Assume that the "mutex" is locked since that is the normal case when it
is checked in the ubifs code.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
|
|
Update scripts/checkpatch.pl from upstream.
One of the many corrections is not creating an error for cover-letters.
Reintroduce U-Boot's
5c761ce58666b3a1695697498598f8bf3484a0c7
checkpatch.pl: Add warning for new __packed additions
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Using sizeof gives the size of the pointer only, not the string. This
could easily lead to crashes when using -l argument.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
|
|
The most significant change is the addition of the --self-test option
which allows to run a consistency check on all MAINTAINERS files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Provide correct file paths.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch adds the bulk clock API tests for the sandbox test suite.
It's very similar to the main test but only uses the _bulk() API and
checks if the clocks are correctly enabled/disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds a "bulk" API to the clock API in order to get/enable/disable
/release a group of clocks associated with a device.
This bulk API will avoid adding a copy of the same code to manage
a group of clocks in drivers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds the bulk reset API tests for the sandbox test suite.
Unlike the main test, it also check the "other" reset signal using the bulk API
and checks if the resets are correctly asserted/deasserted.
To allow the bulk API to work, and avoid changing the DT, the number of resets
of the sandbox reset controller has been bumped to 101 for the "other" reset
line to be valid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds a "bulk" API to the reset API in order to get/deassert/
assert/release a group of reset signals associated with a device.
This bulk API will avoid adding a copy of the same code to manage
a group of reset signals in drivers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Without the units these numbers are confusing. Add a comment about the
unit being 'bytes' and mention 'buildman' as the source.
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
If there is a problem with the parameters to log_add_filter(), the memory
allocated is currently not freed. Fix this.
Reported-by: Coverity (CID: 171962)
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Commit 253c60a breaks the exit value of 'mkimage -T rkimage'
and print the following error:
mkimage: Can't print header for Rockchip Boot Image support: Success
It is not a failure to not print headers, so just display the warning message,
and finish the function properly.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Similarly to ARMV7, on ARMV7M instruction cache memory needs
to be disabled before running linux kernel to avoid kernel to
be stuck.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The Amlogic Meson SoCs serial bindings were not written when serial
support was pushed into Linux and U-Boot.
A clean bindings document has been merged into Linux tree to correctly
handle the multiple clocks feeding the serial peripheral.
This update the U-Boot serial_meson driver with the new compatible
string for Amlogic Meson GX Socs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The Amlogic Meson SoCs embeds up to 256 reset lines, add the corresponding
driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Xilinx changes for v2018.05-rc2
- Various DT changes and sync with mainline kernel
- Various defconfig updates
- Add SPL init for zcu102 revA
- Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
and zc1751-dc3
- Net fixes - xlnx,phy-type
- 64bit axi ethernet support
- arasan: Fix nand write issue
- fpga fixes
- Maintainer file updates
|
|
Patch queue for efi - 2018-04-09
Highlights this time around:
- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...
|
|
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx zcu104 is another customer board. It is sort of zcu102 clone with
some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
zc1751 is based board with dc3 extenstion card which is used for silicon
validation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add support for Xilinx zcu100.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
SPL MMC boot requires to have clock early.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
Add psu init for zc1751 dc cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add psu init for zcu102-revA.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch enables the fixed link support for
all ZynqMP boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no memory which stores mac address that's why generate it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable ethernet phys for zc1751 dc5.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.
To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Targets without net can't use pxe or dhcp boot methods.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
