| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds code missing when CONFIG_DEBUG_UART_OMAP is enabled as
early debugging UART. The code is basically copied from the ns16550
driver.
Signed-off-by: Felix Brack <fb@ltec.ch>
|
|
Build tested in Travis, see:
https://travis-ci.org/abrodkin/u-boot/jobs/462808237
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
The DTS file for the AM3517 had the incorrect CD polarity. Resync with
the fixed DTS file from Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Hi,
setting active menuitem currently can be outside of menu which results in invisible selection
attached Patch fixes this
regards Frank
>From 1d9c4cb8b3e2dd9b0a7a6a2d4a21684d0a099dbf Mon Sep 17 00:00:00 2001
From: Frank Wunderlich <frank-w@public-files.de>
Date: Sun, 2 Dec 2018 11:23:53 +0100
Subject: [PATCH] ensure active menuitem is inside menu
if active menuitem is defined via environment var it can be outside the menu (>=menuitem-count)
this patch resets this definition back to 0
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
|
|
Due to gpio holes management, stm32_pinctrl_get_gpio_dev() must
be updated.
stm32_pinctrl_get_gpio_dev() returns from a given pin selectors
the corresponding bank gpio device and the gpio_offset inside this
gpio bank.
Update also all functions which makes usage of stm32_pinctrl_get_gpio_dev.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As all STM32 SoCs supports CONFIG_CLK flag,
it becomes useless in this driver, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
To allow access to this define by other driver, move
it into gpio.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Move gpio_dev list filling outside probe() to speed-up U-boot
boot sequence execution. This list is populated only when needed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001
board. It depends on Patrice Chotard's patch 'power: regulator: denied
disable on always-on regulator' which prevents power cycling the vmmc
supply. Without this patch the board will not boot as vmmc is
unfortunately used by other board components, not just eMMC and micro SD
card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card
detection input' is required to boot from external micro SD card. Without
this patch no SD card will be detected and hence booting will fail.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
|
|
Add a sandbox DMA driver implementation (provider) and corresponding DM
test.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This adds channels support for dma controllers that have multiple channels
which can transfer data to/from different devices (enet, usb...).
DMA channle API:
dma_get_by_index()
dma_get_by_name()
dma_request()
dma_free()
dma_enable()
dma_disable()
dma_prepare_rcv_buf()
dma_receive()
dma_send()
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[grygorii.strashko@ti.com: drop unused dma_get_by_index_platdata(),
add metadata to send/receive ops, add dma_prepare_rcv_buf(),
minor clean up]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move dma_ops to a separate header file, following other uclass
implementations. While doing so, this patch also improves dma_ops
documentation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
UART booting requires YMODEM support. Add this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add test for the SPL binary size and the bss section size.
This will throw an error at build time if the SPL sections
do not fit in the designated RAM area, thus avoiding oversizing the SPL.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
The pin number (first and last) in the bank definition is missing the
pin base offset shifting. This is causing a miscalculation when
retrieving the register and pin offsets in the GPIO driver causing the
'gpio' command to drive the wrong pins / GPIOs in the second GPIO chip
(the AO bank is driven correctly because the shifting is already 0).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Protect configuration registers with a hardware spinlock.
If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add hardware spinlock in the list of the clocks.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Currently k2 spi boot is broken as the image header
is getting copied to an invalid memory location
CONFIG_SYS_TEXT_BASE - sizeof (struct image_size)
which maps to 0xc000000 - 0x40 = 0xbffffc0 being a reserved
location.
We cannot change the CONFIG_SYS_TEXT_BASE address as the single
stage boots like UART boot will need the address to be 0xc000000
hence override the spl_get_load_buffer to have image_header
address as CONFIG_SYS_TEXT_BASE aka 0xc000000
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
In commit e5e06b65ad65 ("clk: Allow clock defaults to be set also
during re-reloc state") the earlier guard against setting clock
defaults in pre-reloc state was removed. While it is easy to filter
'assigned-clocks' properties for SPL using CONFIG_OF_SPL_REMOVE_PROPS,
no such mechanism exists for the pre-reloc stage of the full U-Boot.
With the default defconfig for the RK3399-Q7 (which filter the
'assigned-clocks' property for the DTS used by SPL anyway), this
caused a pause during startup of the full U-Boot stage that lasted for
almost 10s (due to the CPU not having been clocked up yet).
This reintroduces the guard from commit f4fcba5c5baa ("clk: Allow
clock defaults to be set also during re-reloc state") and extends it
to only apply outside of a TPL/SPL build: i.e. clk_set_defaults will
now run in pre-reloc state for SPL, but only after reloc for the full
U-Boot.
References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
References: commit e5e06b65ad65 ("clk: Allow clock defaults to be set
also during re-reloc state")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The long name apparently can be accumulated using multiple
13-byte slots. Unfortunately we never checked how many we
can actually fit in the buffer we are reading to.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
|
|
The cluster size specifies how many sectors make up a cluster. A
cluster size of zero makes no sense, as it would mean that the
cluster is made up of no sectors. This will later lead into a
division by zero in sect_to_clust(), so better take care of that
early.
The MAX_CLUSTSIZE define can reduced using a define to make some
room in low-memory system. Unfortunately if the code reads a
filesystem with a bigger cluster size it will overflow the buffer.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
|
|
Since commit 8f651ca60ba1 ("pinctrl: stm32: Add get_pins_count() ops")
stm32f746-disco can't boot.
This is due to new memory allocation into STM32 pinctrl driver,
increase SYS_MALLOC_F_LEN from 0xC00 to 0xE00.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Now that many things are converted to Kconfig we can drop most of the
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
LX2160A Soc is based on Layerscape Chassis Generation 3.2
architecture with features:
16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC,
2 64-bit DDR4 memory controller, RGMII, 8 I2C controllers,
3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs,
4 TZASC instances, etc.
SoC personalites:
LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs
LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Voltage regulator LTC3882 device has 0.5% voltage read error.
So for NXP SoC devices this generally equates to 2mV
Update set_voltage_to_LTC for below:
1.Add coorection of upto 2mV in voltage comparison
to take care of voltage read error of voltage regulator
2.Add loop max count kept as 100 to avoid infinte loop.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc,
board type detection is dynamic at boot time
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
I2C is used to access DDR SPD in the DDR initialization for SPL. In
i2c_write process, get_timer() will be called. In board_init_f for SPL,
timer_init() is not called before. The system counter is not enabled and
the counter frequency is not set to 12.5MHz in SPL. The parameters for
do_div() are zero too.
It could not be found until CONFIG_USE_PRIVATE_LIBGCC is enabled in
default. When CONFIG_USE_PRIVATE_LIBGCC is enabled, U-Boot will use its
own set of libgcc functions. As the parameters for do_div() are zero,
__div0 will be called. Then the processor will stay in an endless loop
after calling hang().
This patch will add timer_init() in board_init_f for SPL and fix a
series of issues it caused.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[YS: moveconfig -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
One ls2080a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add ahci compatible support for ls2080a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
[YS: add fallthrough comment]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
One ls1088a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add ahci compatible support for ls1088a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
One ls1046a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add ahci compatible support for ls1046a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
TFABOOT support includes:
- ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be
loaded by trusted firmware
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove unnecessary braces]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
TFABOOT support includes:
- ls1012aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
