summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-01-28Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2009-01-2885xx: Fix compile breakage with MPC8540EVALKumar Gala
Configuring for MPC8540EVAL board... mpc8540eval.c: In function 'checkboard': mpc8540eval.c:53: error: invalid operands to binary / make[1]: *** [mpc8540eval.o] Error 1 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-28Blackfin: fixup misc warnings such as printf's and missing castsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: convert old boards to use COBJS-y Makefile styleMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bf533-stamp: rewrite resource swap logicMike Frysinger
The old swap function tended to clobber unrelated pins and screw up masks. Rewrite the thing from scratch so it only uses the resources it needs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bootldr: implement BF53x/BF56x LDR loaderMike Frysinger
The BF53x/BF56x parts do not have an on-chip ROM to boot LDRs out of arbitrary memory locations, so implement a basic one in software. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: implement real write support for OTPMike Frysinger
Now that real documentation has been released for the OTP interface and the on-chip ROM wrt writing/timings, implement support for reading/writing as well as dumping/locking. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: update on-chip ROM APIMike Frysinger
This brings the API for the on-chip ROM in line with the toolchain and hardware documentation. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: allow serial console to be disabledMike Frysinger
Some devices have no UART device pulled out, so allow people to disable the driver completely in favor of other methods (like JTAG-console). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: support console-over-JTAGMike Frysinger
The Blackfin JTAG has the ability to pass data via a back-channel without halting the processor. Utilize that channel to emulate a console. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: handle new anomalies with resetMike Frysinger
Workaround fun new anomalies related to software reset of the processor. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: pass RETX to LinuxMike Frysinger
Make sure we save the value of RETX at power on and then pass it on to the kernel so that it can nicely debug a "double-fault-caused-a-reset" crash. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: clarify relocation comment during initMike Frysinger
People often ask questions about the init process and when things go from flash to relocated base, so clarify the comments a bit. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: just set SP register directly during initMike Frysinger
No need to set the SP register indirectly to the configured value when it can be set directly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: add portmuxing for UARTs on the BF51xMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: respect CONFIG_CLKIN_HALFMike Frysinger
As pointed out by Ivan Koryakovskiy, the initialization code was not actually respecting the CONFIG_CLKIN_HALF option when configuring the PLL_CTL register. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: use common memcpy routine during initMike Frysinger
Rather than using a local custom memcpy function, just call the existing optimized Blackfin version. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: set default boot SPI CS for BF538/BF539Mike Frysinger
The BF538/BF539 use CS2 for booting off of rather than CS1 like newer Blackfin parts. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: punt unused BF533-STAMP definitionsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: resurrect BF533-STAMP video splash driverMike Frysinger
This video driver used to live in the Blackfin cpu directory, but it was lost during the unification process. This brings it back. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: tighten up post memory coding styleMike Frysinger
No functional changes here; just cleanup code style a bit. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bf537-stamp nand: fix more style errors in previous commitMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: drop dead/wrong debug code in initdram()Mike Frysinger
The DEBUG code in initdram() is quite old and was never really useful, so just drop it altogether. Common Blackfin debug code does a better job. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bf533-ezkit: shuffle flash defines a littleMike Frysinger
Some of the flash defines weren't in the correct location and caused build problems in some configurations, so let's move types and defines to better local locations. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: overhaul i2c driverMike Frysinger
The current Blackfin i2c driver does not work properly with certain devices due to it breaking up transfers incorrectly. This is a rewrite of the driver and relocates it to the newer place in the source tree. Also remove duplicated I2C speed defines in Blackfin board configs and disable I2C slave address usage since it isn't implemented. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: respect CONFIG_SYS_MONITOR_LEN for default flash protectionMike Frysinger
Respect the CONFIG_SYS_MONITOR_LEN define rather than assuming a size of 128kB when setting up the default flash protection region for U-Boot itself. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: respect/check CONFIG_SYS_GBL_DATA_SIZEMike Frysinger
When setting up the global data, rather than relying on sizeof(), use the common CONFIG_SYS_GBL_DATA_SIZE define. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: implement general support for CONFIG_STATUS_LEDMike Frysinger
Here are the Blackfin-specific and board-independent pieces for status leds. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: do not init i2c in Blackfin board initMike Frysinger
The common code takes care of calling i2c_init() when needed, so no point in us doing it as well. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bfin_mac: update port muxingMike Frysinger
Adds support more Blackfin parts and fixes broken muxing for older ones. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: fix dcache handling when doing dma memcpy'sMike Frysinger
Our dcache invalidate function doesn't just invalidate, it also flushes. So rename the function accordingly and fix the dma_memcpy() function so it doesn't inadvertently corrupt the data destination. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: dont generate ldrs with --forceMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: pass --bmode/--initcode when creating ldrMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: minimize time cache is turned off when replacing cplb entriesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: split cache handling out of dma_memcpy()Mike Frysinger
Creating a new dma_memcpy() function that skips all cache checks allows us to use the function in very early init where the cache is not yet setup. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: abort dma_memcpy() for L1 scratchpadMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: rename bootm.c to boot.cMike Frysinger
The boot file contains functions for more than just "bootm", so rename it accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: set more sane default board config valuesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: convert CMD_LINE_ADDR to CONFIG_LINUX_CMDLINE_{ADDR,SIZE}Mike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: add bit defines for DDR partsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: add defines to describe active bootrom behaviorMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28mpc83xx: fix undefined reference to `flush_cache' error in simpc8313 buildKim Phillips
extend commit c70564e6b1bd08f3230182392238907f3531a87e "NAND: Fix cache and memory inconsistency issue" to add the cache.o dependency to the simpc8313 build and fix this: ...Large Page NAND...Configuring for SIMPC8313 board... nand_boot_fsl_elbc.o: In function `nand_boot': nand_spl/board/sheldon/simpc8313/nand_boot_fsl_elbc.c:150: undefined reference to `flush_cache' make[1]: *** [/home/r1aaha/git/u-boot-mpc83xx/nand_spl/u-boot-spl] Error 1 make: *** [nand_spl] Error 2 Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-28mpc8536ds.c: include sata.h to for needed function prototypesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-01-28Command usage cleanupPeter Tyser
Remove command name from all command "usage" fields and update common/command.c to display "name - usage" instead of just "usage". Also remove newlines from command usage fields. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28amcc: Clean up command usage outputPeter Tyser
Update taihu and taishan commands to use cmd_usage() function to display usage messages. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28Standardize command usage messages with cmd_usage()Peter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28pcs440ep: Clean up led command definitionPeter Tyser
The pcs440ep's led command usage formatting is non-standard. It was made standard in preparation for larger command usage updates. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28Clean up diufb command definitionsPeter Tyser
The diufb command usage formatting is non-standard. It was made standard in preparation for larger command usage updates. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28Update CHANGELOG, tiny coding style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-01-27SATA: do not auto-initialize during bootMike Frysinger
Rather than have the board code initialize SATA automatically during boot, make the user manually run "sata init". This brings the SATA subsystem in line with common U-Boot policy. Rather than having a dedicated weak function "is_sata_supported", people can override sata_initialize() to do their weird board stuff. Then they can call the actual __sata_initialize(). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit (git 2.34.1) at 2024-12-29 19:56:57 +0000