summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-07-07mx28evk: Fix PSWITCH key positionFabio Estevam
Fix the position for PSWITCH key. The good benefit of doing this is that boot time is greatly reduced: from 5 seconds to less then 1 second. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx53smd: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53loco: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53evk: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53ard: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53ard: Remove unused CONFIG_MII_GASKETFabio Estevam
CONFIG_MII_GASKET is not defined anywhere, so remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx6: Avoid writing to read-only bits in imximage.cfgVikram Narayanan
If in case this is valid according to the latest datasheet, ignore this patch. Acked-by: Marek Vasut <marex@denx.de>
2012-07-07m28evk: use same notation to alloc the 128kB stackOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Wolfgang Denk <wd@denx.de>
2012-07-07m28evk: drop duplicated definition of CONFIG_OF_LIBFDTOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx28evk: fix board config include guardian macro nameOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx28evk: ensure command definition is in alphabetic orderOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07m28evk: fix board config include guardian macro nameOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07MX28: Fix a typo in mx28_reg_8 macroOtavio Salvador
The macro mistakenly referred to 32bit struct instead of 8bit one. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx6qsabrelite: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2012-07-07mx6qarm2: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2012-07-07ima3-mx53: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07vision2: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07efikamx: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx51evk: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53smd: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53ard: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53evk: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53loco: Remove unused SOBJSFabio Estevam
There is no .S file in this directory, so just remove SOBJS. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx53: Fix mask for SATA reference clockFabio Estevam
SATA_ALT_REF_CLK field corresponds to bits 1 and 2 of offset 0x180c. Fix the mask for these bits. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53loco: Fix revision of Dialog boardsFabio Estevam
Original code was assuming that the fuse revision version for all mx53loco boards based on Dialog PMIC was the same, which is not the case. Force the revision of all Dialog-based boards to 0. This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel for Dialog rev E boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07i.mx: i.mx6x: NO_MUX_I/NO_PAD_I not set correctlyJason Liu
If one PAD does not have mux or pad config register, we need set the NO_MUX_I/NO_PAD_I to 0, the old value is not correct Signed-off-by: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-07EXYNOS: SMDK5250: Enable the pinmux setupRajeshwari Shinde
Use the pinmux configuration function for SMDK5250. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-07-07EXYNOS5: PINMUX: Added default pinumx settingsRajeshwari Shinde
This patch performs the pinmux configuration in a common file. As of now only EXYNOS5 pinmux for SDMMC, UART and Ethernet is supported. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-07-07misc:pmic:trats: Correct procedure of enabling/disabling USB regulatorsŁukasz Majewski
In the MAX8997, LDO regulators needs to preserve previously set voltage values. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-07-07TRATS: initialize panel_info data structure in board fileDonghwa Lee
panel_info data structure is gloable variable, so, I have initialized it in board file. If it is initialized in init_panel_info() like existing, it can't be used in drv_lcd_init() in common/lcd.c because init_panel_info() is called after drv_lcd_init(). Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-07-07Exynos: fix cpuinfo and cpu detectingMinkyu Kang
Since Exynos architecture have new SoCs, need to fix cpuinfo correctly. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
2012-07-07cm-t35: print PCB revision informationNikita Kiryanov
Buffer the PCB revision to avoid multiple eeprom accesses for the same data and print it as a part of board information. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07cm-t35: fix legacy board revision representationNikita Kiryanov
Legacy eeprom layout represents the revision number syntactically (i.e. revision 1.00 is written as 0x100). This is inconsistent with the representation in newer layouts, where it is defined semantically (i.e. 0x64). This patch fixes the issue by replacing the syntactic representation with the semantic one. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07cm-t35: fix incorrect BOARD_REV_SIZE valueNikita Kiryanov
Non-legacy layouts have an extended revision field, but only the first 2 bytes are the PCB revision. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07cm-t35: reduce the environment sizeIgor Grinberg
Reduce the environment size (128KB => 16KB) to improve the environment operations time (e.g. reading, ecc calculation). Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07ARM: OMAP4: Correct the lpddr2 io settings register value.SRICHARAN R
To meet certain timing requirements on the lpddr2 cmd and data phy interfaces ,lpddr iopads have to be configured as differential buffers and a Vref has to be internally generated and provided to these buffers. Correcting the above settings here. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07OMAP5: Change voltages for omap5432Lokesh Vutla
Change voltages for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: DPLL core lock for OMAP5432Lokesh Vutla
No need to Unlock DPLL initially. DDR3 can work at normal OPP from initialozation Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: EMIF: Add support for DDR3 deviceLokesh Vutla
In OMAP5432 EMIF controlller supports DDR3 device. This patch adds support for ddr3 device intialization and configuration. Initialization sequence is done as specified in JEDEC specs. This also adds support for ddr3 leveling. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: ADD precalculated timings for ddr3Lokesh Vutla
Adding precalculated timings for ddr3 with 1cs adding required registers for ddr3 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: Configure the io settings for omap5432 uevm boardLokesh Vutla
This patch adds the IO settings required for OMAP5432 uevm's DDR3 pads Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: ADD chip detection for OMAP5432 SOCLokesh Vutla
This patch adds chip detection for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07OMAP5: Adding correct Control id code for OMAP5430Lokesh Vutla
Control id code for omap5430 ES1.0 is hard coded with a wrong value. This patch corrects the value Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07omap3evm: Add CONFIG_CMD_ASKENVTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07omap3_beagle: Add CONFIG_CMD_ASKENVTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07omap3evm: Set BOOTDELAY to 3Tom Rini
We reduce the bootdelay from 10s to 3s to give users a short but usable window to interrupt the boot process if needed. Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07OMAP3 Beagle: Set BOOTDELAY to 3Tom Rini
We change the bootdelay to give users a little bit longer to break in if needed. Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07omap24xx_i2c: Add AM33XX supportTom Rini
The same places that check for CONFIG_OMAP44XX need to check for CONFIG_AM33XX as we share the same i2c block. Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 16:35:18 +0000