summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-09-18mpc8xxx_spi: fix SPI support on MPC8308RDBIra W. Snyder
The MPC8308RDB Reference Manual states that no bits in the SPMODE register are allowed to change while the enable (EN) bit is set. This driver changes the character length bits (LEN) while the enable (EN) bit is set. Clearing the EN bit while changing the LEN bits makes the driver work correctly on MPC8308RDB. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-09-17Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2012-09-17Merge branch 'master' of git://git.denx.de/u-boot-fdtTom Rini
2012-09-17i2c:soft:multi: Enable soft I2C multibus at Trats development boardŁukasz Majewski
This commit enables multibus handling at Samsung's Trats development board. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Heiko Schocher <hs@denx.de>
2012-09-17i2c:soft:multi: Support for multiple soft I2C buses at Samsung boardsŁukasz Majewski
Support for multiple soft I2C buses. Multibus I2C support is achieved by defining get_multi_{sda|scl}_pin functions to switch between multiple "soft" I2C buses. Common definition of I2C_X I2C buses is provided at <i2c.h>. TEST HW: Samsung's Exynos4210 evt.0.1 - Trats development board Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Heiko Schocher <hs@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Heiko Schocher <hs@denx.de>
2012-09-15fdt: Check if the FDT address is configuredMarek Vasut
In case the "fdt addr" command wasn't ran yet and any other "fdt" subcommand was issued, the system crashed due to NULL pointer being used. This is caused by "fdt addr" command setting up a pointer to the FDT memory location. Prior issuing "fdt addr", the pointer is NULL so calling any other subcommands crashed the u-boot. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
2012-09-14Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
2012-09-13Merge branch 'master' of git://git.denx.de/u-boot-avr32Tom Rini
2012-09-13avr32: add atngw100mkii boardAndreas Bießmann
This patch is derived from an older patch provided by atmel in its buildroot-avr32-v3.0.0.tar.bz2 Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
2012-09-13Fix strict-aliasing warning in dlmallocSimon Glass
This fixes the following warnings in dlmalloc seen with my gcc 4.6. dlmalloc.c: In function 'malloc_bin_reloc': dlmalloc.c:1493: warning: dereferencing pointer 'p' does break strict-aliasing rules dlmalloc.c:1493: warning: dereferencing pointer 'p' does break strict-aliasing rules dlmalloc.c:1490: note: initialized from here dlmalloc.c:1493: note: initialized from here This version is tested on avr32 arch boards. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-12Merge branch 'master' of git://www.denx.de/git/u-boot-ubiTom Rini
2012-09-12Merge branch 'master' of git://www.denx.de/git/u-boot-mmcTom Rini
2012-09-11microblaze: board: Use bi_flashstart instead of CONFIG_SYS_FLASH_BASEMichal Simek
Prepare for device-tree driven configuration. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11microblaze: Clean microblaze initializationMichal Simek
Move board specific function to board_init function in board/ folder Remove externs from generic board.c Use board_init_f function in board.c file. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11microblaze: timer: Prepare for device-tree initializationMichal Simek
Fix CONFIG_SYS_HZ usage in board config. Do not use hardcoded value. Use CONFIG_SYS_HZ instead. Separate static configuration to single block. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-09-11microblaze: intc: Coding style cleanupMichal Simek
Just coding style cleanup. Remove unneeded externs. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11microblaze: intc: Registering interrupt should return valueMichal Simek
Return value to find out if un/registration was succesful. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-09-11microblaze: board: Remove compilation warningMichal Simek
Variable is used when CONFIG_SYS_FLASH_CHECKSUM is used. Warning log: board.c: In function 'board_init': board.c:101: warning: unused variable 's' Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11microblaze: Add support for device tree driven board configurationMichal Simek
This is minimum code required to be able to use device-tree for u-boot initialization. Currently only for device driver initialization. Linker script change ensures DTB to be aligned for both options CONFIG_OF_EMBED and CONFIG_OF_SEPARATE. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net> CC: Simon Glass <sjg@chromium.org>
2012-09-11spi: xilinx: Remove unused variableStephan Linz
Warning is: xilinx_spi.c: In function 'spi_setup_slave': xilinx_spi.c:81: warning: unused variable 'regs' Signed-off-by: Stephan Linz <linz@li-pro.net> CC: Michal Simek <monstr@monstr.eu>
2012-09-11serial: uartlite: Init all uartlites for serial multiMichal Simek
Initialize all possible uartlites and return the first initialized port. For static configuration is initialization done in userial_ports array. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11serial: Support serial multi for MicroblazeMichal Simek
enable serial multi for Microblaze. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11block: systemace: Simplify base and width initializationMichal Simek
Use CONFIG parameters only at one location to simplify the code. Also create ace_readw/writew functions. Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-09-10ubifs: Fix ubifsload when using ZLIBVeli-Pekka Peltola
Using ZLIB compression with UBIFS fails if last data node is not a size of UBIFS_BLOCK_SIZE (4096 bytes). Easiest way to test this is trying to read a file smaller than 4k: => ubifsload 41000000 /etc/fstab Loading file '/etc/fstab' to addr 0x41000000 with size 704 (0x000002c0)... UBIFS error (pid 0): read_block: bad data node (block 0, inode 2506) UBIFS error (pid 0): do_readpage: cannot read page 0 of inode 2506, error -22 Error reading file '/etc/fstab' /etc/fstab not found! exit not allowed from main input shell. => With this patch: => ubifsload 41000000 /etc/fstab Loading file '/etc/fstab' to addr 0x41000000 with size 704 (0x000002c0)... Done => Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com> Cc: kmpark@infradead.org Tested-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2012-09-06mmc: Remove incorrect cmd->flags usageAndy Fleming
There were a couple of drivers that were actually using the flags field of the cmd structure, despite the fact that no one ever *set* that field. When we removed the field, those drivers failed to compile. Replaced the references with the correct usage of resp_type. Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-06omap4 i2c: add support for i2c bus 4Koen Kooi
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
2012-09-05mmc: s5p_sdhci: add the set_mmc_clk for cmu controlJaehoon Chung
Samsung SoC use the cmu control to set clock. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: s5p_sdhci: fixed wrong function argumentJaehoon Chung
Useless code is removed, and get buswidth value. buswidth value will be used to choice the 4bit or 8bit. (Now used 4bit mode in sdhci.c by default) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: s5p_sdhci: set the SDHCI_QUIRK_BROKEN_R1BJaehoon Chung
Samsung SoC is broken busy waiting for R1b type. And clk delay control value is modified the previosuly value. (that value used at the s5p_mmc.c) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: Add a SDHCI quirk for boards that have no CDJoe Hershberger
Some boards have no Card Detect wired. In that case, set the CD test bits in the standard interface. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: Fix version check for clock API in sdhci driverJoe Hershberger
When setting up the clocks in the sdhci driver, the "spec version" must be masked off. Otherwise any time the vendor version is not 0, the check will allways assume the interface is version 3. This breaks when the interface is actually version 1 or 2. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmcinfo: Fix help messageBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc_get_dev: Return error if mmc_init failsBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05tegra: put eMMC environment into the boot sectorsStephen Warren
When I set up Tegra's config files to put the environment into eMMC, I assumed that CONFIG_ENV_OFFSET was a linearized address relative to the start of the eMMC device, and spanning HW partitions boot0, boot1, general* and the user area in order. However, it turns out that the offset is actually relative to the beginning of the user area. Hence, the environment block ended up in a different location to expected and documented. Set CONFIG_SYS_MMC_ENV_PART=2 (boot1) to solve this, and adjust CONFIG_ENV_OFFSET to be relative to the start of boot1, not the entire eMMC. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05env_mmc: allow environment to be in an eMMC partitionStephen Warren
eMMC devices may have hardware-level partitions: 2 boot partitions, up to 4 general partitions, plus the user area. This change introduces optional config variable CONFIG_SYS_MMC_ENV_PART to indicate which partition the environment should be stored in: 0=user, 1=boot0, 2=boot1, 4..7=general0..3. This allows the environment to be kept out of the user area, which simplifies the management of OS-/user-level (MBR/GPT) partitions within the user area. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: detect boot sectors using EXT_CSD_BOOT_MULT tooStephen Warren
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set. Note that the Linux kernel enables access to boot partitions solely based on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only influences access to "general" partitions. eMMC devices affected by this issue exist on various NVIDIA Tegra platforms (and presumably many others too), such as Harmony (plug-in eMMC), Seaboard, Springbank, and Whistler (plug-in eMMC). Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05MMC: u-boot-spl may be compiled without partition supportMikhail Kshevetskiy
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: fix capacity calculation when EXT_CSD_SEC_CNT is usedYoshihiro Shimoda
Since the type of "ext_csd" was array of char, the following calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT] was minus. capacity = ext_csd[EXT_CSD_SEC_CNT] << 0 | ext_csd[EXT_CSD_SEC_CNT + 1] << 8 | ext_csd[EXT_CSD_SEC_CNT + 2] << 16 | ext_csd[EXT_CSD_SEC_CNT + 3] << 24; So, this patch changes the type of "ext_csd" to array of u8. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: sh_mmcif: enable MMC_MODE_HCYoshihiro Shimoda
The controller can control high capacity cards. So, the patch adds the flag. If the flag is not set, "mmcinfo" will fail when a high capacity card is used. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05mmc: fix wrong timeout check in mmc_send_status()Jongman Heo
(!timeout) condition check in mmc_send_status() can never be met, because do-while loop ends up with negative timeout value, -1. Fix the check to handle TIMEOUT case correctly. Signed-off-by: Jongman Heo <jongman.heo@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-04Merge branch 'master' of git://git.denx.de/u-boot-avr32Wolfgang Denk
* 'master' of git://git.denx.de/u-boot-avr32: net:macb: add line break avr32:portmux: fix setup for macb1 avr32: Remove redundant LDSCRIPT definition Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-03net:macb: add line breakAndreas Bießmann
Without this patch we see annoying output like this: ---8<--- U-Boot> dhcp macb1: PHY not foundmacb0: PHY present at 1 macb0: Starting autonegotiation... --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-09-03avr32:portmux: fix setup for macb1Andreas Bießmann
Use portd_mask instead of portc_mask to setup the pins for port D. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-03Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk
* 'master' of git://git.denx.de/u-boot-ubi: ubifs: Fix memory leak in ubifs_finddir Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-03Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-cfi-flash: cfi: Make the flash erase and write operations abortable cfi: Check for blank before erase Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-03Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-ppc4xx: ppc4xx: Canyonlands/Glacier: Squeeze NAND image a bit to fit again Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-09-03ubifs: Fix memory leak in ubifs_finddirStefan Roese
This patch fixes a memory leak in ubifs_finddir(). Signed-off-by: Stefan Roese <sr@denx.de> Cc: dev.ma.dma@gmail.com
2012-09-03ppc4xx: Canyonlands/Glacier: Squeeze NAND image a bit to fit againStefan Roese
This patch removes some superfluous SDRAM init calls to fit the NAND_SPL image into 4k again. Signed-off-by: Stefan Roese <sr@denx.de>
2012-09-03cfi: Make the flash erase and write operations abortableJoe Hershberger
Check for ctrlc() in operations that take time and loop over the flash addresses. In netconsole, tstc() is expensive. Only check once in a while to not slow down the operation significantly. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Stefan Roese <sr@denx.de>
2012-09-03cfi: Check for blank before eraseJoe Hershberger
Added an optional check in the CFI driver to evaluate if the sector is already blank before issuing an erase command. Improves erase time by over a factor of 10 if already blank. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-29 05:47:15 +0000