summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-10-17mx6qsabrelite: enable DCache and MMC bounce bufferDirk Behme
The recent U-Boot version 2012.07 has improved drivers (e.g. MMC and network/FEC) regarding DCache handling. So it should be safe to use the DCache on the i.MX6, now. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-17configs: mx53evk: Remove CONFIG_HAS_ETH1Fabio Estevam
mx53evk has only one Ethernet port, so remove CONFIG_HAS_ETH1 option. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17configs: mx51evk: Remove CONFIG_HAS_ETH1Fabio Estevam
mx51evk has only one Ethernet port, so remove CONFIG_HAS_ETH1 option. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17configs: mx53loco: Remove CONFIG_HAS_ETH1Fabio Estevam
mx53loco has only one Ethernet port, so remove CONFIG_HAS_ETH1 option. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17mx53loco: Adapt the IPU clockFabio Estevam
Since PLL2 now has changed, it is necessary to adapt the CONFIG_IPUV3_CLK accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17mx5: lowlevel_init.S: Fix PLL settings for mx53Fabio Estevam
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz. Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz instead. Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI at 1080p because the IPU clock cannot reach the requested frequency. Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its maximum frequency. Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little bit to allow easier comparison with the original clock setup from FSL U-boot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17mx5: lowlevel_init.S: Split init_clock macroFabio Estevam
init_clock is currently shared between mx51 and mx53 and it contains lots of ifdef's which makes it really hard to follow the code. Split the init_clock between mx51 and mx53 to allow easier readability. No functional changes are made. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mx25: Clean up imx-regs.hBenoît Thébaudeau
Clean up i.MX25 imx-regs.h: - Update mx31 imx-regs.h filename. - Test for __KERNEL_STRICT_NAMES just in case. - Define internal RAM size. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-16i.MX6: mx6qsabrelite: Add splash screen supportEric Nelson
Adds support for HDMI, two LVDS panels and one RGB panel to the SABRE-Lite board. Displays supported: HDMI - 1024 x 768 for maximum compatibility Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1) wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600) wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480) Since the ipuv3_fb display driver currently supports only a single display, this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect or the I2C touch controller of the LVDS and RGB displays in the priority listed above. Setting 'panel' environment variable to one of the names above will override auto-detection. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX6: add HDMI transmitter register declarations from kernel WIP.Eric Nelson
Original source from Pengutronix HDMI driver work: http://git.pengutronix.de/?p=imx/linux-2.6.git;a=commitdiff;h=72c31cd67ac880bd90785af86f8e46f8ea7b3bb0 Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX6: set drive strength for parallel RGB padsEric Nelson
Default drive strength is disabled and won't function. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: ipufb: add const to fb_videomode declarationsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX video: struct fb_videomode can be constEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: declare iomux_v3_cfg_t arrays as constEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: iomux: input pad array can be constEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-16mx6qsabreauto: Pass the board revision to the kernelFabio Estevam
The kernel from Freescale expects that the bootloader passes the board revision. Read the board revision and pass it via get_board_rev(). Without passing the board revision the kernel does not operate properly as the initialization of peripherals are different in revA versus revB boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mx6qsabreauto: Change mmcroot so it works out of boxOtavio Salvador
The mmcroot setting vary between mx6qsabreauto and mx6qsabresd so we move this to the board configuration file. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mxc: Fix SDHC multi-instance clockBenoît Thébaudeau
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not suitable for the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). This patch fixes this issue by adding a configuration field for the SDHC input clock frequency. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Andy Fleming <afleming@gmail.com>
2012-10-16mx35: Fix eSDHC clocksBenoît Thébaudeau
Each eSDHC instance has a dedicated clock. gd->sdhc_clk must also be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-16mx35: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx35 lowlevel_init: - Indent with tabs. - Fix comments. - Use defined values instead of literal constants. - Use defined macros instead of duplicating code. - Use macro parameters with default values instead of #define'd configs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15Merge branch 'agust@denx.de-next' of git://git.denx.de/u-boot-stagingTom Rini
2012-10-15tools/env: Fix build failure from missing header includeJoe Hershberger
This was introduced in: 8679d0ffdcc0beafea8e6942c0c67cf859afa18e - COMMON: Use __stringify() instead of MK_STR() The header is now needed since common.h is not included in this tool. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-10-15kerneldoc: Add myself to the git-mailrc for kerneldocMarek Vasut
Add entry for kerneldoc into the git-mailrc pointing to the U-Boot ML and myself. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-15kerneldoc: Implement "Example" section handlingMarek Vasut
The default kernel-doc strips starting spaces from every single line in the Example section. This makes the code look bad. Thus, implement special handling for this section. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-15kerneldoc: Add nicer CSS stylesheet for HTML docsMarek Vasut
Import basic CSS stylesheet for the HTML documentation. The base for the stylesheet is taken from: http://ds9a.nl/docbook/minimal-page.html I customized the CSS a bit further, for example to add curvy corners to example section and change the tint of gray. The HTML documentation does not look that crude anymore. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-15kerneldoc: Implant DocBook from Linux kernelMarek Vasut
Pull slightly modified version of Documentation/DocBook, the related perl script scripts/kernel-doc and the scripts/docproc.c from Linux kernel and implant it into U-Boot. This will allow smooth generation of kerneldoc style documentation. It was necessary to modify the DocBook/Makefile to work with U-Boot build system. The changes were only minor though and involved replacing the kbuild specific parts. It was also necessary to replace use of variables like KERNEL_VERSION with U_BOOT_VERSION, strings like Linux kernel with U-Boot Bootloader etc. so the generated result actually matches. Finally, it was necessary to adjust docproc.c, since the documentation in U-Boot is located in doc/DocBook instead of Documentation/DocBook as is in case of the Linux kernel. Some parts of the DocBook Makefile are unused, but to allow easier sync with Linux kernel, these parts are still left in. The targets enabled now are "htmldocs" "pdfdocs" "psdocs" "xmldocs" and "cleandocs" to remove the results of documentation build. Linux scripts/docproc.c: commit f0f3ca8d967462dafb815412b14ca3339b9817a6 Date: Wed Jun 15 11:53:13 2011 +0200 Linux scripts/kernel-doc: commit 1b40c1944db445c1de1c47ffd8cd426167f488e8 Date: Sun Aug 12 10:46:15 2012 +0200 Linux Documentation/DocBook: commit bb8187d35f820671d6dd76700d77a6b55f95e2c5 Date: Thu May 17 19:06:13 2012 -0400 Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-15configs: mx6qsabre_common.h: Use default clock definitionsFabio Estevam
Since commit 50d4a707f0 (mx5/6: Define default SoC input clock frequencies) we can use the default clock values. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx6qsabreauto: Add Ethernet supportFabio Estevam
mx6qsabreauto has a AR8031 Gigabit PHY. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx25: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx25 lowlevel_init: - Add comments. - Do not use write32 repeatedly with the same value in order not to increase code size. - Make register values configurable. - Use macro parameters with default values instead of literal constants. - Use defined macros instead of duplicating code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Matthias Weisser <weisserm@arcor.de>
2012-10-15mx31: Fix PDR0_CSI_PODFBenoît Thébaudeau
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0 register is actually composed of two bit-fields: one pre-divider and one post-divider. This patch fixes the CCM access macros and the code using them accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx35: Define MAX and AIPS registersBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx31: Add more CCM access macrosBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5: Optimize lowlevel_init code sizeBenoît Thébaudeau
Optimize mx5 lowlevel_init.S code size: - Compute values at compile time rather than at runtime where possible. - Assign r4 to hold the zero value rather than setting registers to 0 again and again. - Associate a function to setup_pll rather than expanding its large macro code multiple times. - Allocate constant values in section only if used. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15mx6qsabreauto: Use ttymxc3 as consoleOtavio Salvador
The mx6qsabreauto console is different than mx6qsabresd so the console configuration is now set in the board file. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Fix eSDHC supportBenoît Thébaudeau
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do with mxcmmc. Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx25: Define cpu_eth_init() only if neededBenoît Thébaudeau
The FEC is the only SoC Ethernet support available on i.MX25, so define cpu_eth_init() only for it instead of returning a misleading success code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up clocks APIBenoît Thébaudeau
Use the standard mxc_get_clock() instead of exporting internal functions and using literal constant values. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25 clocks: Fix MXC_FEC_CLKBenoît Thébaudeau
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock. Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG clock, so remove the duplicated code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Define more standard clocksBenoît Thébaudeau
Define AHB, IPG and CSPI clocks. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up clock calculationsBenoît Thébaudeau
Avoid possible overflow in clock calculations, and do not waste calls to lldiv() to divide simple ulongs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Fix decode_pllBenoît Thébaudeau
The MFN bit-field of the PLL registers represents a signed value. See the reference manual. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6 clocks: Fix SDHC clocksBenoît Thébaudeau
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although they have dedicated clock paths. Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx51: Fix I2C clock ID checkBenoît Thébaudeau
There are only 2 I²C instances on i.MX51, but 3 on i.MX53. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix MXC_FEC_CLKBenoît Thébaudeau
The FEC clock does not come from PLL1, but from the IPG clock. The previous code was even inconsistent with itself, returning the IPG clock as expected for imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Simplify imx_get_cspiclk()Benoît Thébaudeau
The code handling the dividers was duplicated for each possible input clock, and this function can benefit from the newly introduced get_standard_pll_sel_clk() function instead of duplicating this mux handling code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_uart_clk()Benoît Thébaudeau
This function returned 66500000 instead of the correct lp_apm clock frequency if the CCM.CSCMR1.uart_clk_sel mux is set to 3. This patch fixes this issue by introducing the get_standard_pll_sel_clk() function that will be used by future patches to handle identical muxes used by many other clocks. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_ipg_per_clk()Benoît Thébaudeau
This fixes the "IPG PERCLK" frequency printed by the clocks command. The issue was that get_ipg_per_clk() used periph_clk instead of lp_apm in the case CCM.CBCMR.perclk_lp_apm_sel is set. It also fixes I²C support. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_periph_clk()Benoît Thébaudeau
In the case periph_clk comes from periph_apm_clk, the latter is selected by the CCM.CBCMR.periph_apm_sel mux, which can source the lp_apm clock from its input ♯2. get_periph_clk() returned 0 instead of the lp_apm clock frequency in this case. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Fix get_lp_apm()Benoît Thébaudeau
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024. In that case: - on i.MX51, this clock comes from the output of the FPM, - on i.MX53, this clock comes from the output of PLL4. This patch fixes the code accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Add and use CCSR definitionsBenoît Thébaudeau
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit (git 2.34.1) at 2025-01-19 05:50:02 +0000