| Age | Commit message (Collapse) | Author |
|---|
|
When a mismatch is found trying to write an image for one boot method
to a different boot device, print an error message including the image
header marked target boot device type.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
With support added for Armada 38x, include the bubt command in
ClearFog defconfig.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Ensure that the device to which an image is being written includes
header information indicating boot support for the destination
device.
This is derived from the support in the SolidRun master-a38x vendor
fork.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Replace "U-BOOT" text with correct spelling
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add support for Armada 38x devices in bubt flashing utility.
This is based on (and streamlined from) the support in the SolidRun
master-a38x vendor fork.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.
Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.
This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.
Tested on SolidRun ClearFog devices.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Fix duplication resulting from merging of multiple related series.
Commits cecf38a75, bd02fd29f, and 201a500de added or adjusted SCSI
boot support for ClearFog, but in slightly different locations which
didn't result in a merge conflict.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Register value table for DDR PHY clock divider are wrong. They should be
0 or 1 for divide-by-2 or divide-by-4, respectively. Not 1 or 2. Current
values do not make sense, since 2 cannot be achieved, because the
register is only 1 bit long (mask is set to 1).
This fixes clk dump reporting DDR PHY clock rate differently from Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
- Backplane support and bug fixes
|
|
i2c changes for 2020.07
- add new i2c driver for Broadcom iproc-based socs
- fix cmd: eeprom: Staticize eeprom_i2c_bus
- i2c: muxes: pca954x: add PCA9546 variant
|
|
new ubi command for renaming an UBI volume
|
|
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
|
|
When logical address of a regular extent is 0, the extent is sparse and
consists of all zeros.
Without this when sparse extents are used in a file reading fails with
Cannot map logical address 0 to physical
Signed-off-by: Marek Behún <marek.behun@nic.cz>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
|
|
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable configs to support USB gadget and Mass Storage
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add the USB DWC2 node to u-boot specific dtsi files since Gadget
support is not (yet) available in upstream Linux yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add arch code to initialize USB Gadget mode using the DWC2 controller,
and using the previously added set_mode() phy functions.
[narmstrong: fixup board_usb_cleanup call to phy_meson_gxl_usb2_set_mode]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Add generic_phy_get_by_node() to get a PHY phandle from a node instead
of a udevice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[narmstrong: fixed by including ofnode.h in generic-phy.h]
|
|
Add support for backplane kr on t208xqds: remove board specific fixups
on t208xqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add support for backplane kr on lx2160aqds: remove board specific fixups
on lx2160aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add support for backplane kr on ls1046aqds: remove board specific fixups
on ls1046aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add generic support for backplane kr modes currently available:
10gbase-kr, 40gbase-kr4. Remove platform generic fixups
(armv8/layerscape and powerpc) for ethernet interfaces specified
in device tree as supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
If the board is configured without CONFIG_GIC_V3_ITS, an error occurs:
board/freescale/lx2160a/lx2160a.c: In function ‘ft_board_setup’:
board/freescale/lx2160a/lx2160a.c:673:6: error: unused variable
‘gic_lpi_base’ [-Werror=unused-variable]
673 | u64 gic_lpi_base;
| ^~~~~~~~~~~~
Let's define the variable as __maybe_unused.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add I2C driver support for Broadcom iproc-based socs.
Signed-off-by: Arjun Jyothi <arjun.jyothi@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The eeprom_i2c_bus is not used outside of this file, make it static.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This adds the PCA9546 4-channel i2c bus switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This commit adds the command ubi rename to rename an ubi volume.
The format of the command is: ubi rename <oldname> <newname>.
To enable this command, the option CMD_UBI_RENAME must be selected.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
JTAG ID register is defined by IEEE 1149.1 for device identification.
Use this JTAG ID register for identifying AM65x[0] and J721E[1] devices
instead of using SoC specific registers.
[0] http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
[1] http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Add i.MXRT1020 pins definition.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Add dtsi file for i.MXRT1020.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Add i.MXRT1020 clk driver support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
After the
commit 4213609cc7fb ("drivers: core: use strcmp when find device by name")
the exact DTS node name for PMIC device must be provided.
This patch fixes this issue by providing full DTS node name ('mc34708@8').
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chug <jh80.chung@samsung.com>
|
|
The CONFIG_PHY_FIXED is necessary to allow DSA switch work in U-Boot after
the
commit 3bf135b6c367 ("drivers: net: phy: Ignore PHY ID 0 during PHY probing").
This particular device - LAN9303 - returns phy_id == 0. With
CONFIG_PHY_FIXED enabled HSC and DDC boards work again with the same U-Boot
binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c367
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81aea ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
|
|
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
|
|
Since CONFIG_DISPLAY_BOARDINFO_LATE is no longer used, the checkboard()
function is no longer called.
As it is useful to print the board revision, print it inside
board_late_init() instead.
Also, to avoid GPIO errors related to using a GPIO without requesting it,
move the gpio_request(REV_DETECTION, "REV_DETECT") call prior to its
usage.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
|
|
Since we are using revD1 device tree for all board revisions, the
following can be seen on a revB1 board:
Model: Wandboard i.MX6 Quad Board revD1
Board: Wandboard rev B1
To avoid such confusing messages, disable CONFIG_DISPLAY_BOARDINFO_LATE.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
|
|
On wandboard variants prior to revD1, there is no PMIC populated, so
do not print an error when the reading of the device ID register fails.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
|
