summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-03-24ColdFire: Update uart_port_conf in serial driverTsiChung Liew
Provide proper port passing from serial_init to uart_part_conf. Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2010-03-24ColdFire: Update processors' serial port configurationTsiChung Liew
Provide parameter passing to uart_port_config(). Update port configuration - un-mask it before enable the bits. Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2010-03-24ColdFire: Correct bit definitionTsiChung Liew
Use correct definition for _MASK and _UNMASK. It was combined in the previous used and causes confusion. Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2010-03-24fix cmd_bdinfo.c:354: warning: 'print_eth' defined but not usedPhilippe De Muyter
This fixes the following warnings when running MAKEALL for coldfire : cmd_bdinfo.c:354: warning: 'print_eth' defined but not used Signed-off-by: Philippe De Muyter <phdm at macqel.be>
2010-03-24Adding EP2500 MCF5282 board [PATCH]Michael Durrant
Mercury-EP2500.patch - added Mercury's EP2500 board uses the mcf5282 processor CREDITS.patch Signed-off-by: David Wu <davidwu@arcturusnetworks.com> Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
2010-03-24add block write function to spartan3 slave serial loadWolfgang Wegner
Using seperate function calls for each bit-bang of slave serial load can be painfully slow. This patch adds the possibility to supply a block write function that loads the complete block of data in one call (like it can already be done with Altera FPGAs). On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load time from around 15 seconds to around 3 seconds Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
2010-03-24add ASTRO MCF5373L boardWolfgang Wegner
This patch adds support for ASTRO board(s) based on MCF5373L. Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
2010-03-22Merge remote branch 'origin/master' into nextWolfgang Denk
2010-03-22Prepare v2010.03-rc2Wolfgang Denk
Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-22ep93xx timer: Fix resolution of get_ticks()Matthias Kaehlcke
ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution, as announced by get_tbclk() Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
2010-03-22ep93xx timer: Fix possible overflow in usecs_to_ticks()Matthias Kaehlcke
ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid overflows in intermediate values Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
2010-03-21Merge remote branch 'origin/master' into nextWolfgang Denk
2010-03-21fdt_support: add partitions fixup in mtd nodeAnatolij Gustschin
Allow overwriting defined partitions in the device tree blob using partition info defined in the 'mtdparts' environment variable. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Gerald Van Baren <vanbaren@cideas.com>
2010-03-21cmd history: Match history buffer size to console bufferJohn Schmoller
Match history buffer size to console buffer size. History buffer size was hard coded to 256, artificially limiting the command buffer size. The history buffer now tracks CONFIG_SYS_CBSIZE. Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
2010-03-21console: Fix console buffer overrunJohn Schmoller
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of maximum length will overwrite part of the history buffer, causing the board to die. Expand the console_buffer and hist_lines buffer by one character each to hold the missing NULL char. Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
2010-03-21POST: add progress APIMichael Zaidman
Add POST progress API implemented as weak calls before and after each call to the POST test callback in the post_run_single routine of the post.c file. Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de>
2010-03-21cmd_setexpr: allow memory addresses in expressionsFrans Meulenbroeks
This patch add functionality to use memory addresses in expressions. This increases the power of expressions substantially It adheres to the standard convemtions: memory addresses can be given in the format *address (e.g. *1000) Rationale for this change is that it allows masking off bits from a byte that is obtained by reading data from e.g. i2c. Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Fix warning: control reaches end of non-void function Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-21cmd_i2c.c: added i2c read to memory functionFrans Meulenbroeks
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-21cmd_i2c.c: sorted commands alphabeticallyFrans Meulenbroeks
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-21cmd_i2c.c: reworked subcommand handlingFrans Meulenbroeks
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-21cmd_bootm.c: made subcommand array staticFrans Meulenbroeks
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-21cmd_i2c.c: reduced subaddress length to 3 bytesFrans Meulenbroeks
according to some of the comments the subaddress length is 1 or 2, but we are being prepared for the case it becomes 3. However the code also accepted 4. This repairs this by changing the constand 4 to 3. Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-21nios2: Added support to YANU UARTRenato Andreola
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-03-21nios2: use generic unaligned.hThomas Chou
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-03-21mpc5xxx: Remove all references to MGT5100Detlev Zundel
We do not support a processor that never reached a real customer. Signed-off-by: Detlev Zundel <dzu@denx.de>
2010-03-21video: Fix console display when splashscreen is usedMatthias Weisser
If a splashscreen is used the console scrolling used the scroll size as needed when a logo was displayed. This patch sets the scroll size to the whole screen if a splashscreen is shown. Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
2010-03-21correct a syntax typo in at91_matrix.hAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-03-21env: fix endian ordering in crc tableJeff Angielski
The crc table was being built as little endian for big endian targets. This would cause fw_printenv to always fail with "Warning: Bad CRC, using default environment" messages. Signed-off-by: Jeff Angielski <jeff@theptrgroup.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2010-03-21mpc5121: cpu/mpc512x/diu.c: fix warningsAnatolij Gustschin
Fix warnings while compiling with CONFIG_VIDEO enabled: diu.c: In function 'video_hw_init': diu.c:158: warning: 'return' with no value, in function returning non-void diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int' diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int' Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-03-21console.c: fix problem with splashimageAnatolij Gustschin
If a board uses cfb_console driver and splash image and also defines CONFIG_SILENT_CONSOLE, the user is locked out even if "silent" is not set. It is not possible to get any output, neither on vga console device nor on serial console after redirecting the output to the serial console, since the GD_FLG_SILENT flag remains set. Fix the problem by redirecting the output from frame buffer to serial console if splashimage is used. Only suppress the output if "silent" environment variable was set and don't set the GD_FLG_SILENT flag arbitrarily. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-03-21mod change 755 => 644 for multiple filesThomas Weber
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;' Signed-off-by: Thomas Weber <swirl@gmx.li> Add some more: neither Makefile nor config.mk need execute permissions. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-21mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessorsStefano Babic
Some registers of the mxcmmc driver were accessed using 16 bit accessor functions, because only the LSB is significant. This is not needed and generates warnings. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-21TFTP: allow for adjustable retransmission timoutWolfgang Denk
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds. In some cases (busy networks, slow TFTP servers) this caused very slow transfers. A new environment variable "tftptimeout" allows to set this timeout. Lowering this value may make downloads succeed faster in networks with high packet loss rates or with unreliable TFTP servers. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-03-21Fix PCI_BASE_ADDRESS_5 handling in pci_hose_config_device()Wolfgang Denk
Signed-off-by: FUJITA Kazutoshi <fujita@soum.co.jp> Signed-off-by: <wd@denx.de> Acked-by: Stefan Roese <sr@denx.de>
2010-03-21cmd_mmc remove \nFrans Meulenbroeks
This patch removes the \n after the help message for mmcinfo. This resulted in an empty line being displayed after the mmcinfo line when the help command was given. Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-03-16nios2: Added support to YANU UARTRenato Andreola
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-03-16nios2: use generic unaligned.hThomas Chou
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-03-14Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
2010-03-14asm-blackfin/unaligned.h: add for zlib codeMike Frysinger
The new zlib code wants asm/unaligned.h, so have the Blackfin version pull in the asm-generic/unaligned.h. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-14asm-generic/unaligned.h: dynamic default unaligned accessesMike Frysinger
This is based on the asm-arm/unaligned.h, but made generic so all arches that cannot do unaligned accesses can utilize it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-13video: Fix console display when splashscreen is usedMatthias Weisser
If a splashscreen is used the console scrolling used the scroll size as needed when a logo was displayed. This patch sets the scroll size to the whole screen if a splashscreen is shown. Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
2010-03-12Prepare v2010.03-rc1Wolfgang Denk
Coding style cleanup, update CHANGELOG. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12standalone eepro100_eeprom: fix build errorWolfgang Denk
Building examples/standalone/eepro100_eeprom triggers this error: In file included from include/common.h:629, from eepro100_eeprom.c:24: include/net.h: In function 'NetReadIP': include/net.h:430: warning: implicit declaration of function 'memcpy' eepro100_eeprom.c: At top level: eepro100_eeprom.c:81: error: conflicting types for 'memcpy' include/net.h:430: error: previous implicit declaration of 'memcpy' was here Fix this. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12Update .gitignore's: add some generated filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12mpc82xx: Remove SL8245 board and the now orpahned sk98lin network driver.Detlev Zundel
This code has compile problems and the company does not even exist any more. So we take the liberty to drop support for it. Signed-off-by: Detlev Zundel <dzu@denx.de> CC: Wolfgang Denk <wd@denx.de> CC: Ben Warren <biggerbadderben@gmail.com>
2010-03-1285xx: Drop FIT support to allow u-boot image to fit in 512kKumar Gala
The 36-bit build exceeds the 512k size we have. Removing FIT type image support allows us to fit and we dont really use it. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-03-12Cosmetic change - indentation correction.Michael Zaidman
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
2010-03-12cmd_mtdparts.c: prevent printbuffer overflowsAnatolij Gustschin
The length of configured MTDPARTS_DEFAULT string could be greater than console printbuffer size. Replace printf() by puts() to avoid potential buffer overflows. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-03-12Fix MPC8536DS documentationFrans Meulenbroeks
This patch corrects small mistake in the register list in doc/README.mpc8536ds. These registers are 32 bits and this one starts at ....c not ....e When using the ...c address I can boot from sd, when using the ...e address I cannot. Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com> Acked-by: Hu Mingkai <B21284@freescale.com>
2010-03-12doc: add README for CONFIG_HWCONFIG optionHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>