summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-12-04am335x: cpsw: optimize cpsw_recv to increase network performanceVladimir Koutny
In 48ec5291, only TX path was optimized; this does the same also for RX path. This results in huge increase of TFTP throughput on custom am3352 board (from 312KiB/s to 1.8MiB/s) and eliminates occasional transfer timeouts. Signed-off-by: Vladimir Koutny <vladimir.koutny@streamunlimited.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Tom Rini <trini@ti.com>
2013-12-04pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAMHardik Patel
Signed-off-by: Hardik Patel <hardik.patel@volansystech.com>
2013-12-04davinci: fix Master Priority Registers locationViktar Palstsiuk
MSTPRI0 (Master Priority 0 Register) sits at 0x01C14110 not at 0x01C14114 Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
2013-12-04arm: am335x: Add DT (FDT) support to Siemens boardsStefan Roese
Enable FDT support for all Siemens AM335x boards. To support newer Linux kernels with DT booting. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Roger Meier <r.meier@siemens.com> Cc: Lukas Stockmann <lukas.stockmann@siemens.com> Cc: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher<hs@denx.de>
2013-12-04am335x_evm: Update nandboot to use partitions and DTTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-04arm: omap3: Add uart4 omap3 adddressMichael Trimarchi
This patch add the OMAP34XX_UART4 memory address Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2013-12-04ARM: OMAP5+: Remove unnecessary EFUSE settingsLokesh Vutla
Certain EFUSE settings were recommended for the first four lots of OMAP5 ES1.0 silicon. These are not applicable for OMAP5 ES2.0 and DRA7 silicon. So removing these EFUSE settings. Reported-by: Griffis, Brad <bgriffis@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-04ARM: dra7_evm: Add SATA supportRoger Quadros
The evm has a SATA port. Enable SATA configuration and inititialize the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: DRA7xx: Add PRCM and Control information for SATARoger Quadros
Adds the necessary PRCM and Control register information for SATA on DRA7xx. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: omap5_uevm: Add SATA supportRoger Quadros
The uevm has a SATA port. Inititialize the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: OMAP5: Add SATA platform glueRoger Quadros
Add platform glue logic for the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: OMAP5: Add PRCM and Control information for SATARoger Quadros
Adds the necessary PRCM and Control register information for SATA on OMAP5. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: OMAP5: Add Pipe3 PHY driverRoger Quadros
Pipe3 PHY is used by SATA, USB3 and PCIe modules. This is a driver for the Pipe3 PHY. Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ahci: Fix cache align error messagesRoger Quadros
Align the ATA ID buffer to the cache-line boundary. This gets rid of the below error mesages on ARM v7 platforms. scanning bus for devices... ERROR: v7_dcache_inval_range - start address is not aligned - 0xfee48618 ERROR: v7_dcache_inval_range - stop address is not aligned - 0xfee48818 CC: Aneesh V <aneesh@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ahci: Error out with message on malloc() failureRoger Quadros
If malloc() fails, we don't want to continue in ahci_init() and ahci_init_one(). Also print a more informative error message on malloc() failures. CC: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039SRICHARAN R
When core power domain hits oswr, then DDR3 memories does not come back while resuming. This is because when EMIF registers are lost, then the controller takes care of copying the values from the shadow registers. If the shadow registers are not updated with the right values, then this results in incorrect settings while resuming. So updating the shadow registers with the corresponding status registers here during the boot. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04ARM: DRA: EMIF: Change DDR3 settings to use hw levelingSRICHARAN R
Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using software leveling. This was done since hardware leveling was not working. Now that the right sequence to do hw leveling is identified, use it. This is required for EMIF clockdomain to idle and come back during lowpower usecases. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04ARM: DRA7: Add is_dra7xx cpu check definitionSRICHARAN R
A generic is_dra7xx cpu check is useful for grouping all the revisions under that. This is used in the subsequent patches. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04am33xx: Stop modifying certain EMIF4D registersTom Rini
Based on the definitive guide to EMIF configuration[1] certain registers that we have been modifying (and are documented registers) should be left in their reset values rather than modified. This has been tested on AM335x GP EVM and Beaglebone White. [1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Javier Martinez Canillas <javier@dowhile0.org> Cc: Heiko Schocher <hs@denx.de> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04ARMV7: OMAP4: Add twl6032 supportOleg Kosheliev
Added chip type detection and twl6032 support in the battery control and charge functions. Based on Balaji T K <balajitk@ti.com> patches for TI u-boot. Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
2013-12-04ARMV7: OMAP4: Add struct for twl603x dataOleg Kosheliev
The data struct is used to support different PMIC chip types. It contains the chip type and the data (e.g. registers addresses, adc multiplier) which is different for twl6030 and twl6032. Replaced some hardcoded values with the structure vars. Based on Balaji T K <balajitk@ti.com> patches for TI u-boot. Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
2013-12-04ARM: OMAP4: Fix bug in omap4470_volts structLubomir Popov
The struct incorrectly referenced SMPS1 for all three power domains. Fixed this by using SMPS2 and SMPS5 as appropriate. Add some comments and choose voltage values that correspond to voltage selection codes. Signed-off-by: Lubomir Popov <l-popov@ti.com>
2013-12-04pcm051: Support for revision 3Lars Poeschel
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on the board. The difference for u-boot is that is has other DDR3 RAM on it: 1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and 2. Both configurations are 512 MiB. Configure your u-boot build with pcm051_rev3 for the new RAM and pcm051_rev1 for the old RAM configuration. Board revision 2 has to use pcm051_rev1 also. Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-12-04cm_t335: add support for pca9555 i2c gpio extenderIlya Ledvich
Add support for the 16 bits pca9555 i2c to gpio extender featured by the SB-T335 baseboard. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-04cm_t335: add support for status LEDIlya Ledvich
Add support for status LED. Use the STATUS_LED APIs for indicating a boot progress. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-04cm_t335: add cm_t335 board supportIlya Ledvich
Add cm_t335 board directory, config file. Enable build. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> [trini: Adapt Makefile] Signed-off-by: Tom Rini <trini@ti.com>
2013-12-03socfpga: Adding Freeze Controller driverChin Liang See
Adding Freeze Controller driver. All HPS IOs need to be in freeze state during pin mux or IO buffer configuration. It is to avoid any glitch which might happen during the configuration from propagating to external devices. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03board: trats2: update Tizen partition definitionsPiotr Wilczek
This patch updates Tizen partions layout. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03board: trats2: fix access to samsung registersPiotr Wilczek
This patch use 'samsung_get_base' common functions to access registers. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03board: trats2: fix environmental variablesPiotr Wilczek
In this patch variable names are used instead of hardcoded names Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03board: trats2: remove unused defines from config filePiotr Wilczek
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03exynos: spl: Add a custom spi copy functionRajeshwari Shinde
This patch implements a custom spi_copy funtion to copy u-boot from SF to RAM. This is faster then iROM spi_copy funtion as this runs spi at 50Mhz and also in WORD mode of operation. Changed a printf in pinmux.c to debug just to avoid the compilation error in SPL. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03arm: rmobile: Remove config.mkNobuhiro Iwamatsu
Renesas ARM SoCs (R-Mobile, R-Car) are armv7 only. This drops armv5 supprt from PLATFORM_CPPFLAGS and remove config.mk of rmobile. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-12-03arm: kzm9g: Fix undefined reference to `__aeabi_uldivmod' errorNobuhiro Iwamatsu
The kzm9g board fails in building with -march=armv7-a. This fixs this problem by converting to do_div(). ----- USE_PRIVATE_LIBGCC=yes ./MAKEALL kzm9g ... arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_us': arch/arm/cpu/armv7/rmobile/timer.c:41: undefined reference to `__aeabi_uldivmod' arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_ms': arch/arm/cpu/armv7/rmobile/timer.c:47: undefined reference to `__aeabi_uldivmod' ----- Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2013-12-03arm: rmobile: Add support koelsch boardNobuhiro Iwamatsu
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB, Quad SPI, Ethernet, and more. This patch supports the following functions: - DDR3-SDRAM - SCIF Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03arm: rmobile: Add support R8A7791Nobuhiro Iwamatsu
Renesas R8A7791 is CPU with Cortex-A15. This supports the basic register definition and GPIO and framework of PFC. Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03arm: rmobile: Add support lager boardNobuhiro Iwamatsu
The lager board has R8A7790, 4GB DDR3-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - DDR3-SDRAM - SCIF Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03arm: rmobile: Add support R8A7790Nobuhiro Iwamatsu
Renesas R8A7790 is CPU with Cortex-A7 and A15. This supports the basic register definition and GPIO and framework of PFC. Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com> Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-03arm: rmobile: Move lowlevel_init.o to taget of each CPUNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-12-03arm: exynos: fix the align for exynos4_power structureMinkyu Kang
res3 should be 4bytes Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Dominik Klein <dominik.klein@gmx.com>
2013-12-03arm: exynos: fix set_mmc_clk for exynos4x12Jaehoon Chung
Fix the set_mmc_clk() for exnos4x12. If board is exynos4x12, mmc clock should be set to wrong value. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-03trats: usb: Add usb_cable_connected() functionPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-02Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-12-02Merge branch 'serial' of git://git.denx.de/u-boot-microblazeTom Rini
2013-12-02Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
2013-12-02Blackfin: remove executable permission of AWK scriptMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-02Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2013-12-02serial: zynq: Remove unused #definesSoren Brinkmann
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Series-to: trini, uboot
2013-12-02trats2: enable dfu and thor protocol for Tizen downloadPiotr Wilczek
Trats2 config is updated to support DFU mode. Malloc pool must be increased for DFU buffer allocation. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-02trats2: enable ums support on Trats2Piotr Wilczek
This patch adds support for USB and enables 'ums' command on Trats2 board. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit (git 2.34.1) at 2025-01-31 18:26:38 +0000