| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for CM-T35 board
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Supported:
MMC
IDE
PMIC
SPI flash
LEDs
I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Add initial support for MX53EVK board support.
FEC, SD/MMC, UART, I2C, have been supported.
Signed-off-by: Jason Liu <r64343@freescale.com>
|
|
Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.
Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx
Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
|
|
The MPC852 based mgsuvd and kmsupx4 boards from keymile
were initially ported but later on not developed further. So
the respective files were removed to avoid unneeded merging
and maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
|
|
I've probably got the best chance of getting access to these
boards in order to test things, and since Joe's e-mail is
bouncing, update the MAINTAINERS entry to reflect this.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The ATUM8548 board is no longer maintained and thus we are removing
support for it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This adds support for the SHMIN SH7706 board(T-SH7706LAN).
The CPU of this board is SH7706.
There are SDRAM of 32M byte, Flash memory of 512K byte, Serial,
10Base Ether and MMC.
http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htm
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
|
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
* Processor upto 1.2GHz
* Parallel 1Gb x8 DDR2-1066 MHz
* 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
* Footprints for eMMC/eSD NAND & MMC x8 card
* 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
* SEAF memory board, subset of PISMO2
With Peripherals:
* 4.3” WVGA 24-bit LCD
* Audio codecs (AC97 & I2S), TSI
* VGA camera
* Video in via 3 RCA jacks, and HDMI type C out
* Marvell 88W8688 802.11bg/BT module
* GPS RF IC
* Dual analog mics & speakers, headset jack, LED, ambient light sensor
* USB2.0 HS host (A), OTG (micro AB)
* FE PHY, PCIE Mini Card slot
* GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR
This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
|
|
- serial console in PSC1
- 128MiB DRAM
- 32MiB Flash
- FEC Ethernet
- 2 I2C busses
- FPGA on CS3
- IDE
- VGA SMI501
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year. Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
start with sheevaplug configuration
add modifications by Alexander Holler <holler@ahsoftware.de>
change RAM definitions to one bank (128 MB)
change ident string and prompt
define MTD partitions and default environment variables
add support for LEDs
Signed-off-by: Eric Cooper <ecc@cmu.edu>
|
|
Board support for the Guntermann & Drunck CATCenter Io.
Board support for the Guntermann & Drunck IoCon.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some U-Boot images for X-ES boards support multiple products in the same
family. For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards. To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.
While we're at it, change the board config file and make targets to be
lowercase.
Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
This patch adds support for the HP Jornada flashboards
that were made in 2008. Older flashroms should work if
memory registers are adjusted.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Adpted for TEXT_BASE -> CONFIG_SYS_TEXT_BASE rename.
Removed now redundant board/jornada/config.mk file.
Removed unused empty jornada_init() function to silence
"jornada.c:35: warning: 'jornada_init' defined but not used"
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
The following hardware is currently supported:
- UART
- USB Host
- FPGA
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
128MB NOR module support.
Define __io to get harddrive working.
Fix saving of environment into OneNAND.
Boot from harddrive when possible.
Add missing MAINTAINERS entry.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
This patch adds support for the Palm Tungsten|C PXA255 board. The support
includes:
- LCD
- MMC
- UART
- NOR
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
|
|
This patch removes some functionality from at91rm9200ek board but the
remaining functionality does now work with newer at91 code and
arm-relocation.
Currently missing features are:
- dataflash booting (due to missing HW for testing)
- MMC/SD-Card
- first stage bootloader support is completely removed (not needed for
NOR)
Cause this board was (some days ago) reference for all at91rm9200 based
boards this should be a good starting point to convert all remaining
at91rm9200 borads to at91 code. Aside from that this is a good base to
get some drivers between at91sam/at91rm/avr32 merged.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
The NC650 / CP850 boards have long been unmaintained and left broken.
As obviously nobody is interested in that code any more, we may as
well remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
I'm noticed that IGEP maintainer isn't in the correct place within
the ARM subsection: it's supposed to be in alphabetical order by
maintainer. This patch fix this.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
|
|
The IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family.The IGEP module
solution based upon TI OMAP3 provides a low-power/low-cost platform
for a variety of consumer/industrial/medical devices.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
|
|
Adds support for the ARM quad-core Cortex-A9 processor
This system includes a motherboard(Versatile Express), daughterboard
(Coretile), and SOC(Cortex-A9 quad core). The serial port, ethernet,
and flash systems work with these additions. The naming convention
is:
SOC -> CortexA9 quad core = ca9x4
daughterboard -> Coretile = ct
motherboard -> Versatile Express = vxp
This gives ca9x4_ct_vxp.c as the board support file.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
|
|
This patch provides support for the A4M072 board with the following features:
UART
NOR flash
FEC Ethernet
External SRAM
I2C EEPROM
CompactFlash cards on IDE/ATA port
USB Host
PCI initialization
The 7-segment LED indicator is not yet supported.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
|
|
|
|
The patch adds support for TTECH vision2 board.
The board has 512MB RAM, SDHC slot and 4MB SPI
device from StMicron.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
The CCM board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
Add support code for bluestone board wth APM821XX processor based.
This patch includes early board init, misc init, configure EBC,
initializes UIC, MAKEALL, board.cfg and MAINTAINERS file.
Signed-off-by: Tirumala R Marri <tmarri@apm.com
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The board includes:
* ADSP-BF561 rev. 0.5
* 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG)
* Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell)
* SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB)
* FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB)
* Spartan6-LX150 (memory-mapped; both PPIs also connected)
* See http://www.skutek.com/
Signed-off-by: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Support for the Blackfin System Development Platform (SDP) base module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
This patch adds support for the jadecpu board using the
MB86R01 'Jade' SoC from Fujitsu.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
|
