summaryrefslogtreecommitdiff
path: root/MAKEALL
AgeCommit message (Collapse)Author
2009-06-12dm355 evm supportDavid Brownell
Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller: http://c6000.spectrumdigital.com/evmdm355/revd/ Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling: http://focus.ti.com/docs/prod/folders/print/tms320dm355.html This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12ZOOM2 Add initial support for Zoom2Tom Rix
Zoom2 is a new board from Texas Instruments and LogicPD The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is the product description web page http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp This patch provides a zoom2 base target by copying zoom1 and by making some obvious changes. To configure, run make omap3_zoom2_config Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-05-1582xx, ids8247: added ids8247 board to MAKEALL scriptHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2009-04-16at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev
The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04Add support for the AT91RM9200EK Board.Ulf Samuelsson
The AT91RM9200-EK Evaluation Board supports the AT91RM9200 ARM9-based 32-bit RISC microcontroller and enables real-time code development and evaluation. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507 with - NOR (cfi driver) - DataFlash - USB OHCI - Net - I2C (hard) Signed-off-by: Ulf Samuelsson <ulf@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-02Blackfin: bf518f-ezbrd: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf526-ezbrd: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf538f-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf527-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf548-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-30MPC85xx: Add MPC8569MDS board supportHaiying Wang
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-26Merge branch 'master' of git://git.denx.de/u-boot-at91Wolfgang Denk
2009-03-25ARM: Add the imx31_phycore_eet board to MAKEALLGuennadi Liakhovetski
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2009-03-22at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-20Add support for the digsy MTC board.Grzegorz Bernacki
This is the InterControl custom device based on the MPC5200B chip. Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-188xx: add support for new keymile kmsupx4 board.Heiko Schocher
This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-02-16MPC85xx: TQM8548: add support for the TQM8548_AG moduleWolfgang Grandegger
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory, CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module with "$ make TQM8548_AG_config". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16MPC85xx: TQM8548: add support for the TQM8548_BE moduleWolfgang Grandegger
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN interface. With NAND support, the image is significantly larger and TEXT_BASE is adjusted accordingly. U-Boot can be built for this module with "$ make TQM8548_BE_config". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-10qong: support for Dave/DENX QongEVB-LITE boardIlya Yanok
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-01Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-01-28OMAP3: Add Zoom1 board supportDirk Behme
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here: http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add Pandora supportDirk Behme
Add Pandora support. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add EVM boardDirk Behme
Add EVM board support. Signed-off-by: Manikandan Pillai <mani.pillai@ti.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add Overo boardDirk Behme
Add Overo board support. Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28OMAP3: Add common power code, README, and BeagleBoardDirk Behme
Add BeagleBoard support, common power code and README. Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-27Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk
2009-01-27MIPS: Add VCT board series support (Part 3/3)Stefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26ppc4xx: Add GDsys PowerPC 440 ETX board support.Dirk Eibach
Board support for the Guntermann & Drunck PowerPC 440 ETX module. Based on the AMCC Yosemite board support by Stefan Roese. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-24Initial support for Nomadik 8815 development boardAlessandro Rubini
The NMDK8815 board is distributed by ST Microelectornics. Other (proprietary) code must be run to unlock the CPU before U-Boot runs. doc/README.nmdk8815 outlines the boot sequence. This is the initial port, with basic infrastructure and a working serial port. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-24Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2009-01-24Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2009-01-24Added initial eNET board supportGraeme Russ
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2009-01-23Merge branch 'next'Kim Phillips
2009-01-24powerpc: 83xx: add support for the kmeter1 boardHeiko Schocher
This patch adds support for the kmeter1 board from Keymile, based on a Freescale MPC8360 CPU. - serial console on UART 1 - 256 MB DDR2 RAM - 64 MB NOR Flash - Ethernet RMII Mode over UCC4 - PHY SMSC LAN8700 Signed-off-by: Heiko Schocher <hs@denx.de>
2009-01-2385xx: Add a 36-bit physical configuration for MPC8572DSKumar Gala
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary to allow for larger memory sizes. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23mpc83xx: New board support for SIMPC8313Ron Madrid
This patch will create a new board, SIMPC8313, from Sheldon Instruments. This board boots from NAND devices and is configureable for either large or small page devices. The board supports non-soldered DDR2, one ethernet port, a Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected to the eLBC providing glue logic to a TMS320C67xx DSP. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-23microblaze: Rename ml401 to microblaze-genericMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-21Merge branch 'master' into nextKim Phillips
2008-12-19XPedite5200 board supportPeter Tyser
Initial support for Extreme Engineering Solutions XPedite5200 - a MPC8548-based PMC single board computer. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19XPedite5370 board supportPeter Tyser
Initial support for Extreme Engineering Solutions XPedite5370 - a MPC8572-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-10microblaze: Remove XUPV2P boardMichal Simek
--- Microblaze platforms use generic settings and to have many platforms is confusing that's why I decided to remove this platform from U-BOOT. ml401 tree is sufficient for covering all Microblaze platforms. This change will go through microblaze custodian tree.
2008-12-09MAKEALL: Automatically use parallel buildsWolfgang Denk
Add logic to the MAKEALL script to determine the number of CPU cores on the system, and run a parallel build if there is more than one. Usually this significantrly accelerates builds. Allow to manually adjust the number of parallel make jobs by using the "BUILD_NCPUS" environment variable. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-20powerpc: 83xx: add support for the kmeter1 boardHeiko Schocher
This patch adds support for the kmeter1 board from Keymile, based on a Freescale MPC8360 CPU. - serial console on UART 1 - 256 MB DDR2 RAM - 64 MB NOR Flash - Ethernet RMII Mode over UCC4 - PHY SMSC LAN8700 Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-09Merge branch 'master' of git://git.denx.de/u-boot-at91Wolfgang Denk
2008-11-04Custom AFEB9260 board supportSergey Lapin
This patch provides support for AFEB9260 board, a product of OpenSource hardware and software. Some commertial projects are made with this design. A board is basically AT91SAM9260-EK with some modifications and different peripherals and different parts used. Main purpose of this project is to gain experience in hardware design. More info: http://groups.google.com/group/arm9fpga-evolution-board (In Russian only, sorry). Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-11-03ColdFire: Add MCF5301x CPU and M53017EVB supportTsiChung Liew
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-10-24ppc4xx: New board avnet fx12 minimodulGeorg Schardt
This patch adds support for the avnet fx12 minimodul. It needs the "ppc4xx: Generic architecture for xilinx ppc405" patch from Ricardo. Signed-off-by: Georg Schardt <schardt@team-ctech.de> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21ppc4xx: Add GDSys neo 405EP board supportDirk Eibach
Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21ppc4xx: Add AMCC Arches board support (dual 460GT)Adam Graham
The Arches Evaluation board is based on the AMCC 460GT SoC chip. This board is a dual processor board with each processor providing independent resources for Rapid IO, Gigabit Ethernet, and serial communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH, UART, EEPROM and temperature sensor, along with a shared debug port. The two 460GT's will communicate with each other via shared memory, Gigabit Ethernet and x1 PCI-Express. Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Victor Gallardo <vgallardo@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-25 10:00:48 +0000