summaryrefslogtreecommitdiff
path: root/arch/arm/Kconfig
AgeCommit message (Collapse)Author
2019-04-12am335x, guardian: Add support for the bosch guardian boardSjoerd Simons
Add support for the Bosch Guardian board. CPU : AM335X-GP rev 2.1 Model: Bosch AM335x Guardian I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-08arm: sunxi: Enable DM_MMC on required SoCsJagan Teki
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular target making invalid reading to the disk drive. Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40 would eventually end-up with scsi disk read failures like [1] So, enable DM_MMC in all places of respective SoC's instead of enabling them globally to Allwinner platform. Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40. [1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-03-03configs: fsl: move DDR specific defines to KconfigRajesh Bhagat
Moves below DDR specific defines to Kconfig: CONFIG_FSL_DDR_BIST CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE CONFIG_FSL_DDR_INTERACTIVE CONFIG_FSL_DDR_SYNC_REFRESH Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: ls1043a: move SCSI_AHCI and SCSI to arm/KconfigPeng Ma
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface support. this changed is to fixed the ls1043ardb compile warning as fallows: ===================== WARNING ====================== This board does not use CONFIG_DM_SCSI. Please update the storage controller to use CONFIG_DM_SCSI before the v2019.07 release. Failure to update by the deadline may result in board removal.See doc/driver-model/MIGRATION.txt for more info. ==================================================== Signed-off-by: Peng Ma <peng.ma@nxp.com> [PK: reword the patch subject] Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19lx2160aqds : Add support for LX2160AQDS platformPankaj Bansal
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [PK: Sqaush patch for "secure boot defconfig" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160ardb : Add support for LX2160ARDB platformPriyanka Jain
LX2160ARDB is an evaluation board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> [PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han and re-arrange defconfig] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-09bcm963158: add initial supportPhilippe Reynes
This add the initial support of the broadcom reference board bcm963158 with a bcm63158 SoC. This board has 1 GB of ram, 512 MB of flash (nand), 2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN). Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09bcm63158: add initial supportPhilippe Reynes
This add the initial support of the broadcom bcm63158 SoC family, only the cpu, dram and uart are supported. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-01-30arm: sunxi: Enable DM_MMCJagan Teki
Enable DM_MMC for all Allwinner SoCs, this will eventually enable BLK. Also removed DM_MMC enablement in few parts of sunxi configurations. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2019-01-24Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-01-24arm64: zynqmp: Move SoC sources to mach-zynqmpMichal Simek
Similar changes was done for Zynq in past and this patch just follow this pattern to separate cpu code from SoC code. Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/* And also fix references to these files. Based on "ARM: zynq: move SoC sources to mach-zynq" (sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup proper SPI dependencyMichal Simek
Select DM_SPI/DM_SPI_FLASH for the whole SoC. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24ARM: zynqmp_r5: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: zynqmp: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-24arm64: versal: Setup DM_ETH/MMC if NET/MMC is enabledMichal Simek
Setup proper ETH/MMC dependency for the whole platform. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-01-18arm: sunxi: Enable CLK, RESETJagan Teki
CLK and DM_RESET drivers are now available for all of the Allwinner platforms, so enable them in arch/arm/Kconfig Enabling CLK will select DM_RESET by default. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-09sunxi: drop default SPL_LIBDISK_SUPPORT enablementAndre Przywara
There is no code for using partition labels in the Allwinner SPL port. Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was meant to guard partition code for the SPL. Remove the "imply" line in the Kconfig to make this obvious and avoid unneeded code inclusions, helping to keep the H6 SPL code small. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-06Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini
2019-01-01imx: rename mx8m,MX8M to imx8m,IMX8MPeng Fan
Rename mx8m,MX8M to imx8m,IMX8M Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jon Nettleton <jon@solid-run.com>
2018-12-26exynos: imply SYS_THUMB_BUILDGuillaume GARDET
This patch allows smaller binaries. This is needed for and has been tested on Arndale board, as u-boot.bin is now bigger than the 512K load limit, with GCC8, without thumb mode. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-12-10Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2018-12-07arm: socfpga: imply SPL options instead of selectSimon Goldschmidt
For a small SPL, it should be possible to build without SPI(-flash) drivers or wihout MMC drivers. For this to work, we have to change from 'select'ing options to 'imply'ing them. With this change, I can have SPL trimmed to my hard-wired starting method (SPI-NOR or MMC) while still including all drivers in U-Boot. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-12-07usb: introduce a separate config option for DM USB deviceJean-Jacques Hiblot
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not for device. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-12-04ARM: rmobile: Set environment variable containing CPU typeMarek Vasut
Set environment variable 'platform' containing the CPU type. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2019.01 microblaze: - Use default functions for memory decoding - Showing model from DT zynq: - Fix spi flash DTs - Fix zynq_help_text with CONFIG_SYS_LONGHELP - Tune cse/mini configurations - Enabling cse/mini testing with current targets zynqmp: - Enable gzip SPL support - Fix chip detection logic - Tune mini configurations - DT fixes(spi-flash, models, clocks, etc) - Add support for OF_SEPARATE configurations - Enabling mini testing with current targets - Add mini mtest configuration - Some minor config setting nand: - arasan: Add subpage configuration net: - gem: Add 64bit DMA support
2018-11-28arm: MediaTek: add basic support for MT7629 boardsRyder Lee
This adds a general board file based on MT7629 SoCs from MediaTek. Apart from the generic parts (cpu) we add some low level init codes and initialize the early clocks. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-26arm64: zynqmp: Enable SPL_SEPARATE_BSS by defaultMichal Simek
BSS section was all the time separated for SPL but this symbol wasn't enabled. It is necessary to have it enabled for OF_SEPARATE configuration where DTB is appended to u-boot with DTB. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-16bcm6858: add initial supportPhilippe Reynes
This add the initial support of the broadcom bcm6858 SoC family, only the cpu, dram and uart are supported. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-11-16Merge tag 'pull-14nov18' of git://git.denx.de/u-boot-dmTom Rini
- virtio implementation and supporting patches - DM_FLAG_PRE_RELOC fixes - regmap improvements - minor buildman and sandbox things
2018-11-14Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2018-11-14arm: qemu: Add a Kconfig in the board directoryBin Meng
This adds a Kconfig file in the board directory, so that some board-specific options can be specified there. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-13sunxi: Imply fitImage supportMarek Vasut
Enable modern fitImage format on sunxi. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Tom Rini <trini@konsulko.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-31arm: socfpga: imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITIONSimon Goldschmidt
Using imply for SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION instead of select ensures we can build without partition support (used to build a network boot only version of SPL and U-Boot). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-10-25Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imxTom Rini
Merged imx8 architecture, fix build for imx8 + warnings
2018-10-22imx: add Kconfig entry for i.MX8QXPPeng Fan
Add Kconfig entry for i.MX8QXP Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2018-10-19arm: lpc32xx: add CONFIG_ARCH_LPC32XX build optionVladimir Zapolskiy
The explicit arch specific build symbol allows to group supported boards, generalize common config options and it will serve as a dependency for platform only drivers. Two related board defconfigs are resynced after the change. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2018-10-16arm64: zynqmp: Enable MP by default via KconfigMichal Simek
Simplify defconfig for ZynqMP but keep option not to enable it for mini targets. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16arm64: versal: Add support for new Xilinx Versal ACAPsMichal Simek
Xilinx is introducing Versal, an adaptive compute acceleration platform (ACAP), built on 7nm FinFET process technology. Versal ACAPs combine Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent Engines with leading-edge memory and interfacing technologies to deliver powerful heterogeneous acceleration for any application. The Versal AI Core series has five devices, offering 128 to 400 AI Engines. The series includes dual-core Arm Cortex™-A72 application processors, dual-core Arm Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more than 1,900 DSP engines optimized for high-precision floating point with low latency. The patch is adding necessary infrastructure in place without enabling platform which is done in separate patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-27Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.11 - Handle BOARD_LATE_INIT via Kconfig SPL: - Enable GZIP for all partitions types(not only for kernel) ZynqMP: - Rearrange pmufw version handling - Support newer PMUFW with improved fpga load sequence Zynq: - Cleanup config file - Simplify zybo config by enabling option via Kconfig net: - Fix gems max-speed property reading - Enable support for fixed-link phys
2018-09-26arm64: zynqmp: Handle CONFIG_BOARD_LATE_INIT via KconfigMichal Simek
Disable BOARD_LATE_INIT via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-23arm: qemu-arm: enable RTC (PL031) by defaultAKASHI Takahiro
Virtual machine provided by qemu-arm has a ARM PL031 Real Time Clock device. With this patch, the driver is enabled by default. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-09-11arm: K3: Add initial support for TI's K3 generation of SoCsLokesh Vutla
Add support for Texas Instruments' K3 Generation Processor families. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-10arm: stm32: Remove redundant thumb build selectionVikas Manocha
All armv7m arch builds are thumb & SYS_THUMB_BUILD is already selected by CPU_ARMV7M. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-08-26cmd: ubi: change 'default y' for SUNXI to 'imply' in KconfigMasahiro Yamada
It is not preferred to put SUNXI-specific code in the common place. Change it to 'imply' property of ARCH_SUNXI. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-08-13ARM: socfpga: Remove adhoc ethernet reset and configurationMarek Vasut
Remove ad-hoc ethernet syscon registers configuration and reset support. Reset is now handled by the reset framework and the syscon registers are set in the dwmac_socfpga.c driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-06mvebu: consolidate SPL boot device config symbolsBaruch Siach
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of board specific symbols. This commit enables the boot device selection menu to all mvebu platforms, but it is only effective on Turris Omnia and gdsys Controlcenter DC platforms. A following commit will enable boot selection for other platforms. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2018-07-30dm: Change CMD_DM enablingMichal Simek
CMD_DM is used for debug purpose and it shouldn't be enabled by default via Kconfig. Unfortunately this is in the tree for quite a long time that's why solution is to use imply DM for all targets which are enabling DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-30Kconfig: Sort bool, default, select and imply optionsMichal Simek
Fix Kconfig bool, default, select and imply options to be alphabetically sorted. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-07-30Kconfig: Replace spaces with tabs and missing newlineMichal Simek
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig entry should be separated by newline. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
generated by cgit (git 2.34.1) at 2024-12-26 09:28:04 +0000