summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm926ejs/mxs/spl_boot.c
AgeCommit message (Collapse)Author
2020-05-18common: Drop log.h from common headerSimon Glass
Move this header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18common: Drop init.h from common headerSimon Glass
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-07ARM: mxs: spl_boot.c: make early_delay more robustRasmus Villemoes
It's true that booting normally doesn't take long enough for the register to roll (which actually happens in a little over an hour, not just a few seconds). However, the counter starts at power-on, and if the board is held in reset to be booted over USB, one actually risks hitting wrap-around during boot, which can both result in too short delays (if the "st += delay" calculation makes st small) and theoretically also unbound delays (if st ends up being UINT_MAX and one just misses sampling digctl_microseconds at that point). It doesn't take more code to DTRT, and once bitten, twice shy. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2019-12-02common: Move serial functions out of common.hSimon Glass
These functions belong in serial.h so move them over. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27ARM: mxs: support full SPL frameworkMans Rullgard
This allows using the full SPL framework on mxs devices. In this mode, the u-boot.sb image loaded by the boot ROM contains only the SPL which then loads U-Boot proper or a kernel in falcon mode. Signed-off-by: Mans Rullgard <mans@mansr.com>
2018-04-27ARM: mxs: move spl dataMans Rullgard
With full SPL enabled, the loaded image overwrites the mxs_spl_data location. Moving it a slightly lower address fixes this. Signed-off-by: Mans Rullgard <mans@mansr.com>
2016-12-19ARM: mxs: Remove unused variable warningMarek Vasut
Shuffle the macros around a little to remove the following warning when building for i.MX28: arch/arm/cpu/arm926ejs/mxs/spl_boot.c:44:26: warning: ‘iomux_boot’ defined but not used [-Wunused-const-variable=] static const iomux_cfg_t iomux_boot[] = { ^~~~~~~~~~ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Stefano Babic <sbabic@denx.de>
2015-04-22ARM: mxs: Get boot mode from OCRAMJörg Krause
Reading the boot mode pins after power-up does not necessarily represent the boot mode used by the ROM loader. For example the state of a pin may have changed because a recovery switch which was pressed to enter USB mode is already released after plugging in USB. The ROM loader stores the value a fixed address in OCRAM. Use this value instead of reading the boot map pins. The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the MX28EVK: http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch Leave the boot mode detection for the i.MX23 untouched. Someone has to test whether the i.MX ROM loader does also store the boot mode in OCRAM and if the address match. This patch superseeds my incorrect patch: ARM: mxs: get boot mode from OTP http://patchwork.ozlabs.org/patch/454930/ Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks> Cc: Stefano Babic <sbabic@denx.de>
2015-02-10arm: mxs: Add 'Wait for JTAG user' if booted in JTAG modeGraeme Russ
When booting in JTAG mode, there is no way to use soft break-points, and no way of knowing when SPL has finished executing (so the user can issue a 'halt' command to load u-boot.bin for example) Add a debug output and simple loop to stop execution at the completion of the SPL initialisation as a pseudo break-point when booting in JTAG mode Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10arm: mxs: Add debug outputs and comments to mxs SPL source filesGraeme Russ
It is difficult to track down fail to boot issues in the mxs SPL. Implement the following to make it easier: - Add debug outputs to allow tracing of SPL progress in order to track where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must be defined to enable debug output in SPL - Add TODO comments where it is not clear if the code is doing what it is meant to be doing, even tough the board boots properly (these comments refer to existing code, not to any code added by this patch) Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2014-11-07cppcheck cleanup: fix nullPointer errorsWolfgang Denk
There are a number of places where U-Boot intentionally and legally accesses physical address 0x0000, for example when installing exception vectors on systems where these are located in low memory. Add "cppcheck-suppress nullPointer" comments to silence cppcheck where this is intentional and legal. Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-04-02mxs: fix warning in SPL with console supportStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-01arm: mxs: Add serial console support into SPLMarek Vasut
Add support for serial console into the i.MX23/i.MX28 SPL. A full, uncrippled serial console support comes very helpful when debugging various spectacular hardware bringup issues early in the process. Because we do not use SPL framework, but have our own minimalistic SPL, which is compatible with the i.MX23/i.MX28 BootROM, we do not use preloader_console_init(), but instead use a similar function to start the console. Nonetheless, to avoid blowing up the size of the SPL binary, this support is enabled only if CONFIG_SPL_SERIAL_SUPPORT is defined, which is disabled by default. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-04-01arm: mxs: Properly set GD pointer in SPLMarek Vasut
Set the GD pointer in the SPL to a defined symbol so various functions from U-Boot can be used without adverse side effects. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-03-31arm: mxs: Adjust the load address of U-Boot and SPL for HABMarek Vasut
When using HAB, there are additional special requirements on the placement of U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the U-Boot binary a little further from the begining of the DRAM, so the HAB CST and IVT can be placed in front of the U-Boot binary. This is necessary, since both the U-Boot and the IVT must be contained in single CST signature. To make things worse, the IVT must be concatenated with one more entry at it's end, that is the length of the entire CST signature, IVT and U-Boot binary in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can easily align them all and then produce the length field as needed. As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus we place the IVT at 0x8000 offset, CST right past IVT and claim the size is correct. The HAB library accepts this setup. Finally, to make sure the vectoring in SPL still works even after moving the SPL from 0x0 to 0x1000, we add a small function which copies the vectoring code and tables to 0x0. This is fine, since the vectoring code is position independent. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2013-09-10ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut
Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01lib: consolidate hang()Andreas Bießmann
Delete all occurrences of hang() and provide a generic function. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> [trini: Modify check around puts() in hang.c slightly] Signed-off-by: Tom Rini <trini@ti.com>
2013-01-21mx23: SPL: Add boot mode supportOtavio Salvador
This adds the boot mode support for i.MX23 processors. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-12-04mxs: Staticize SPL functionsMarek Vasut
The MXS SPL didn't mark local functions "static". Fix it. This also makes the SPL smaller by roughly 300 bytes. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15serial: mxs: spl: Remove empty serial_* functions from SPL codeMarek Vasut
Remove the empty bodies from serial_* functions from MXS SPL code. These empty implementations are now in common/serial.c instead so declaring them also in the SPL code would cause a colision once serial multi is enabled unconditionally. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
2012-09-04MX28: Fixup the ad-hoc use of DIGCTL_MICROSECONDSMarek Vasut
Use proper struct-based access for this register in the SPL code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mxs: Convert sys_proto.h prefixes to 'mxs'Otavio Salvador
The sys_proto.h functions (except the boot modes) are compatible with i.MX233 and i.MX28 so we use 'mxs' prefix for its methods. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: Remove not required explicit iomux-mx28.h includeOtavio Salvador
The iomux header is included on sys_proto.h so to avoid SoC specific header inclusion. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-09-01mxs: Reowork SPL to use 'mxs' prefix for methodsOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: reorganize source directory for easy sharing of code in i.MXS SoCsOtavio Salvador
Most code can be shared between i.MX23 and i.MX28 as both are from i.MXS family; this source directory structure makes easy to share code among them. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>