summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm926ejs/start.S
AgeCommit message (Collapse)Author
2012-02-12arm, arm926ejs: Enable icache only if CONFIG_SYS_ICACHE_OFF is not definedChristian Riesch
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Add option CONFIG_SYS_EXCEPTION_VECTORS_HIGHChristian Riesch
The V bit of the c1 register of CP15 should not be cleared on DA850 SoCs since they have no valid memory at 0x00000000. This patch introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH that allows setting the correct value for the V bit. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Flush the data cache before disabling itSughosh Ganu
The current implementation invalidates the data cache before turning it off and causes problems on the hawkboard. See the discussion in http://lists.denx.de/pipermail/u-boot/2012-January/115212.html According to the ARM926EJ-S Technical Reference Manual, the cache should be flushed instead. Also fix the comments to match code. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Rebased and corrected commit message. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2012-02-12arm, arm926ejs: Do cpu critical inits only for boards that require itChristian Riesch
This patch reverts commit ca4b55800ed74207c35271bf7335a092d4955416 "arm, arm926ejs: always do cpu critical inits" since it impacts all arm926ejs based configurations and caused problems, e.g., with the hawkboard. Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines from the board configurations that need low level initialization. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2011-12-06arm, arm926ejs: always do cpu critical initsHeiko Schocher
always do the cpu critical inits in cpu_init_crit, and only jump to lowlevel_init, if CONFIG_SKIP_LOWLEVEL_INIT is not defined. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Wolfgang Denk <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at>
2011-12-06arm, arm926ejs: Fix clear bss loop for zero length bssChristian Riesch
This patch fixes the clear bss loop for bss sections that have zero length, i.e., where __bss_start == __bss_end__. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-11-03arm, davinci: add support for new spl frameworkHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03arm, arm926: fix missing symbols in NAND_SPL modeHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add NOR Boot Configuration WordHeiko Schocher
to add the "NOR Boot Configuration Word" on AM18xx based boards, define CONFIG_SYS_DV_NOR_BOOT_CFG. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13led: remove camel casing of led identifiers globallyJason Kridner
Result of running the following command to address Wolfgang's comment about camel case: for file in `find . | grep '\.[chS]$'`; do perl -i -pe 's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done Discussion: http://patchwork.ozlabs.org/patch/84988/ Signed-off-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-04Convert ISO-8859 files to UTF-8Albert ARIBAUD
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source tree, which could cause issues with the patchwork review system. This commit converts all ISO-8859 files to UTF-8. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-26replace CONFIG_PRELOADER with CONFIG_SPL_BUILDAneesh V
replace all occurences of CONFIG_PRELOADER with CONFIG_SPL_BUILD Signed-off-by: Aneesh V <aneesh@ti.com>
2011-04-27Replace obsolete e-mail addressAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-03-27arm: fix incorrect monitor protection region in FLASHPo-Yu Chuang
Monitor protection region in FLASH did not cover .rel.dyn and .dynsym sections, because it uses __bss_start to compute monitor_flash_len. Use _end instead. Add _end to linker scripts for end of u-boot image Add _end_ofs to all the start.S. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27rename _end to __bss_end__Po-Yu Chuang
Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-02-21arm relocation: Fix calculation of board_init_rAlexander Stein
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
2011-02-02ARM: */start.S: code cleanupLiu Hui-R64343
Remove the useless code from start.S Signed-off-by: Jason Liu <r64343@freescale.com> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-13ARM: */start.S: use canonical asm syntaxWolfgang Denk
Make code build with older tool chains. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-09arm: fixloop(): do not use r8 for relocationAndreas Bießmann
r8 is used for global_data and should therefore be left alone! For C code the compiler flag --fixed-r8 does the job, but in assembler we need to be aware of that fact. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: relocate_code(): do not set register uselessAndreas Bießmann
In case we are still at relocation target address before relocation we do not need to load the registers needed for relocation. We should instead skip the whole relocation part and jump over to clear_bss immediately. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: copy_loop(): use scratch registerAndreas Bießmann
This patch uses r1 as scratch register for copy_loop(). Therefore we do not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the destination address of relocation). Therefore r7 can be used later on for other purposes. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-08arm: add 8-byte alignment for ABI compliance before board_init_fHeiko Schocher
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch> Tested on following boards: arm1136: qong armv7: omap3_beagle arm926ejs: magnesium, tx25 Signed-off-by: Heiko Schocher <hs@denx.de> cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch> cc: Albert ARIBAUD <albert.aribaud@free.fr>
2010-10-29Drop support for CONFIG_SKIP_RELOCATE_UBOOTWolfgang Denk
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29Drop support for CONFIG_SYS_ARM_WITHOUT_RELOCWolfgang Denk
When this define was introduced, the idea was to provide a soft migration path for ARM boards to get adapted to the new relocation support. However, other recent changes led to a different implementation (ELF relocation), where this no longer works. By now CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it actually hurts because it obfuscates the actual code by sprinkling it with lots of dead and non-working debris. So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-26ARM: fix address setup in start.SDarius Augulis
Fix address setup bug for ARM. This bug stops u-boot booting if CONFIG_SKIP_RELOCATE_UBOOT is defined. Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
2010-10-26Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated valueWolfgang Denk
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26ARM: Use consistent assembler syntaxGray Remlin
Signed-off-by: Gray Remlin <g_remlin@rocketmail.com> Acked-by: Heiko Schocher <hs@denx.de>
2010-10-19Merge branch 'elf_reloc'Wolfgang Denk
Conflicts: arch/arm/include/asm/config.h board/LaCie/edminiv2/config.mk board/karo/tx25/config.mk board/logicpd/imx27lite/config.mk doc/README.arm-relocation Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk
The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-13arm926ejs, tx25: add support for ELF relocationsHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-10-13arm: implement ELF relocationsAlbert Aribaud
ELF relocation tables generated with linker option -pie can be used to fixup code and data in a single loop at relocation, removing the need for manual fixups anywhere else in the code. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-11arm: bugfix: replace ble with blo in start.S filesAlbert Aribaud
Generalized misuse of ble within relocation and bss initialization loops caused one iteration too many. Instead of ble ('branch if lower or equal'), use blo ('branch if lower'). While we're at it, fix all 'addreee' typos. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-09-19ARM: implement relocation for ARM926Heiko Schocher
Change the implementation for arm926 to relocate the code to an arbitrary address in RAM. Adapt the TX25 (i.MX25), magnesium board to test the changes. On the tx25 board TEXT_BASE is set to the final relocation address to prevent one more copying of u-boot code when relocating. More info see: doc/README.arm-relocation da850 board: Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca>
2010-06-22ARM: Align stack to 8 bytesVitaly Kuzmichev
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted in Procedure Call Standard for the ARM Architecture: http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html Unaligned SP also causes the problem with variable-length arrays allocation when VLA address becomes less than stack pointer during aligning of this address, so the next 'push' in the stack overwrites first 4 bytes of VLA. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-04-13arm: Move cpu/$CPU to arch/arm/cpu/$CPUPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
generated by cgit (git 2.34.1) at 2024-12-28 11:50:03 +0000