summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm926ejs
AgeCommit message (Collapse)Author
2011-08-03AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/masterXu, Hong
Rework for AT91SAM9RL SoC, makes it build again. Based on the work for AT91SAM9260-EK. V4: US->USART, cosmetics Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03AT91: change common at91sam9261 files to compile with new schemeAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)Reinhard Meyer
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-07-26Timer: Remove reset_timer_masked()Graeme Russ
In some circumstances, reset_timer_masked() was called be timer_init() in order to perform architecture specific timer initialisation. In such cases, the required code in reset_timer_masked() has been moved into timer_init()
2011-07-26Timer: Remove reset_timer() for non-Nios2 archesGraeme Russ
2011-07-26Timer: Remove set_timer completelyGraeme Russ
2011-07-26replace CONFIG_PRELOADER with CONFIG_SPL_BUILDAneesh V
replace all occurences of CONFIG_PRELOADER with CONFIG_SPL_BUILD Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-17Remove volatile qualifier in get_ram_size() callsAlbert ARIBAUD
Checkpatch.pl complains about the volatile qualifier in calls to get_ram_size(). Remove this qualifier in the prototype and in the calls where it is useless, and leave it only in the function body where it is needed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-14MX27: Update to autogenerated asm-offsets.hStefano Babic
On i.MX27, the asm-offsets.h file is not yet generated as it should be. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Matthias Weisser <weisserm@arcor.de>
2011-07-14imx: Add auto generation of asm-offsets.h for imx25Matthias Weisser
Offsets to registers may be needed in asm code. This patch adds automated generation of these offsets form C structures. Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-07-14imx: Use correct imx25 reset.cMatthias Weisser
imx25 used the wrong reset.c from imx27 Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-07-14imx: Add get_tbclk() function for imx25Matthias Weisser
Need this function for autoboot keyd Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-07-14mx27: Make the UART port number explicitFabio Estevam
mx27_uart_init_pins does the IOMUX setting for UART1 port. Change the function name to make the UART port number explicit. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-04arm920t/at91: add clock.cAndreas Bießmann
This patch adds an copy of arm926ejs/at91/clock.c to arm920t/at91. The arm926ejs specialities are removed from arm920t version and vice versa. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-06-21arm926ejs/at91/lowlevel_init.S: fix definesEric Benard
atmel rework changed define names which broke this file Signed-off-by: Eric Bénard <eric@eukrea.com>
2011-05-18at91: fixed at91sam9263 system fileDaniel Gorsulowski
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2011-05-18AT91: fix timer.c - remove reset_timer()Reinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18AT91: change includes from asm/arch/io.h to asm/io.hReinhard Meyer
and remove the now unused asm/arch-at91/io.h Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18AT91: fix related at91 system/driver filesReinhard Meyer
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-04-27Replace obsolete e-mail addressAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-04-27Orion5x: Correct DRAM bank detectionRogan Dawes
2011-04-27I2C: add i2c support for Armada100 platformLei Wen
Add i2c support to aspenite board with Armada100 soc. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27I2C: add i2c support for Pantheon platformLei Wen
Add i2c support to dkb board with pantheon soc. Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27mx25: Make the UART port number explicit in its setup functionFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-03-27arm: fix incorrect monitor protection region in FLASHPo-Yu Chuang
Monitor protection region in FLASH did not cover .rel.dyn and .dynsym sections, because it uses __bss_start to compute monitor_flash_len. Use _end instead. Add _end to linker scripts for end of u-boot image Add _end_ofs to all the start.S. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27rename _end to __bss_end__Po-Yu Chuang
Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-02-21ARM: Add Support for Marvell Pantheon Familiy SoCsLei Wen
Pantheon Family processors are highly integrated SoCs based on Sheeva_88SV331x-v5 PJ1 cpu core. Ref: http://www.marvell.com/products/processors/communications/marvell_pantheon_910_920_pb.pdf SoC versions Supported: 1) PANTHEON920 (TD) 2) PANTHEON910 (TTC) Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21arm relocation: Fix calculation of board_init_rAlexander Stein
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
2011-02-02arm926ejs: timer: Replace bss variable by gdrHeiko Schocher
Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc bss values in the arm926ejs timers implementation. The usage of bss values in drivers before initialisation of bss is forbidden. In that special case some data in .rel.dyn gets corrupted. This patch is similiar to the patch Dirk Behme posted for the armv7/omap-common/timer.c and added suggestions from Reinhard Meyer. Tested on the arm926ejs mx27 based magnesium board Tested on the arm926ejs kirkwood based suen3 board Signed-off-by: Heiko Schocher <hs@denx.de> cc: Albert ARIBAUD <albert.aribaud@free.fr> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Stefano Babic <sbabic@denx.de> cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-02-02ARM: */start.S: code cleanupLiu Hui-R64343
Remove the useless code from start.S Signed-off-by: Jason Liu <r64343@freescale.com> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-02-02DaVinci: Remove incorrect CONFIG optionSandeep Paulraj
The option CONFIG_SOC_DM6447 seems to have ended up in the code by mistake. It is not used anywhere and there is no chip called DM6447. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02DaVinci DM6467: Fix Build ErrorSandeep Paulraj
This commit fixes build errors on the DM6467 port. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02DaVinci DM6467: Added ET1011C (LSI) PHY supportSandeep Paulraj
Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling ET1011C gigabit phy. which overrides get_link_speed function from default implementation. This enables output of 125 MHz reference clock on SYS_CLK pin. Signed-off-by: Prakash PM <prakash.pm@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-01-09miiphy: convert to linux/mii.hMike Frysinger
The include/miiphy.h header duplicates a lot of things from linux/mii.h. So punt all the things that overlap to keep the API simple and to make merging between U-Boot and Linux simpler. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-12-16arm: Add Support for Marvell ARMADA 100 Familiy SoCsPrafulla Wadaskar
ARMADA 100 Family processors are highly integrated SoCs based on Sheeva_88SV331x-v5 PJ1 cpu core. Ref: http://www.marvell.com/products/processors/applications/armada_100 SoC versions Supported: 1) ARMADA168/88AP168 (Aspen P) 2) ARMADA166/88AP166 (Aspen M) 3) ARMADA162/88AP162 (Aspen L) Contributors: Eric Miao <eric.y.miao@gmail.com> Lei Wen <leiwen@marvell.com> Mahavir Jain <mjain@marvell.com> Signed-off-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-13ARM: */start.S: use canonical asm syntaxWolfgang Denk
Make code build with older tool chains. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-11davinci: Rewrite timer.c to use tbl/tbu emulation variables in gdNick Thompson
This change allows the davinci timer functions to be used before relocation since it avoids using static variables prior to BSS being made available. The code is based on that used in the at91 timers, modified to use a davinci specific hardware timer. It also maintains reset_timer() to allow deprecated timer usage to continue to work (for example, in nand_base.c) Signed-off-by: Nick Thompson <nick.thompson@ge.com> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Tested-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk
2010-12-09arm: fixloop(): do not use r8 for relocationAndreas Bießmann
r8 is used for global_data and should therefore be left alone! For C code the compiler flag --fixed-r8 does the job, but in assembler we need to be aware of that fact. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: relocate_code(): do not set register uselessAndreas Bießmann
In case we are still at relocation target address before relocation we do not need to load the registers needed for relocation. We should instead skip the whole relocation part and jump over to clear_bss immediately. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: copy_loop(): use scratch registerAndreas Bießmann
This patch uses r1 as scratch register for copy_loop(). Therefore we do not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the destination address of relocation). Therefore r7 can be used later on for other purposes. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-08arm: add 8-byte alignment for ABI compliance before board_init_fHeiko Schocher
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch> Tested on following boards: arm1136: qong armv7: omap3_beagle arm926ejs: magnesium, tx25 Signed-off-by: Heiko Schocher <hs@denx.de> cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch> cc: Albert ARIBAUD <albert.aribaud@free.fr>
2010-12-07AT91: fix EMAC gpio init in at91sam9260_devices.cReinhard Meyer
The AT91SAM9G20 BOOT ROM apparently initializes PA23 and PA24 to multi drive (open drain). Revert this, if those pins are going to be used for MII. Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-11-21imx: Get fec mac address from fuseLiu Hui-R64343
The patch is to support getting FEC MAC address from fuse bank. Signed-off-by: Jason Liu <r64343@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de>
2010-11-17Switch from archive libraries to partial linkingSebastien Carlier
Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17ARM: fix linker file for newer ld supportAlbert Aribaud
older ld emitted all ELF relocations in input sections named .rel.dyn, whereas newer ld uses names of the form .rel*. The linker script only collected .rel.dyn input sections. Rewrite to collect all .rel* input sections. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-29Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk
Conflicts: include/configs/km_arm.h Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-29Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk
2010-10-29Drop support for CONFIG_SKIP_RELOCATE_UBOOTWolfgang Denk
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29Drop support for CONFIG_SYS_ARM_WITHOUT_RELOCWolfgang Denk
When this define was introduced, the idea was to provide a soft migration path for ARM boards to get adapted to the new relocation support. However, other recent changes led to a different implementation (ELF relocation), where this no longer works. By now CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it actually hurts because it obfuscates the actual code by sprinkling it with lots of dead and non-working debris. So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
generated by cgit (git 2.34.1) at 2025-01-14 22:56:52 +0000