summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm926ejs
AgeCommit message (Collapse)Author
2012-12-11mxs: i2c: Implement algorithm to set up arbitrary i2c speedMarek Vasut
This algorithm computes the values of TIMING{0,1,2} registers for the MX28 I2C block. This algorithm was derived by using a scope, but the result seems correct. The resulting values programmed into the registers do not correlate with the contents in datasheet. When using the values from the datasheet, the I2C clock were completely wrong. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2012-12-10davinci: fixed cpu resetDavide Bonfanti
The reset procedure works on watchdog timer while before it was modifying TIMER_1 registers. Tested on DM365. Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
2012-12-09at91sam9x5: enable USB support for 9x5ek board.Richard Genoud
Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-12-07mxs: SPL: Generalize memory initializationOtavio Salvador
Use a generic 'dram_vals[]' array that has the full initialization sequence and rename the initialization method so it doesn't has a frequency on its name. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-12-04mxs: Staticize SPL functionsMarek Vasut
The MXS SPL didn't mark local functions "static". Fix it. This also makes the SPL smaller by roughly 300 bytes. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04mxs: Properly setup VDDD in power supply setup codeMarek Vasut
The memory setup code adjusted the VDDD voltage. Remove this adjustment and configure the VDDD voltage correctly in the power supply setup code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04mxs: Implement common function to setup VDDxMarek Vasut
Implement common function to setup the VDDIO, VDDD and VDDA voltage. Right now, there are two almost identical functions to setup VDDIO and VDDD, which is prone to breakage. Pull out the differences into constant structure and pass them as an argument to the common function. Moreover, the function has almost identical loops for setting higher and lower VDDx voltage. Merge these two loops. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26Merge remote-tracking branch 'u-boot-atmel/master'Albert ARIBAUD
2012-10-22common: Discard the __u_boot_cmd sectionMarek Vasut
The command declaration now uses the new LG-array method to generate list of commands. Thus the __u_boot_cmd section is now superseded and redundant and therefore can be removed. Also, remove externed symbols associated with this section from include/command.h . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-22common: Add .u_boot_list into all linker filesMarek Vasut
Add section for the linker-generated lists into all possible linker files, so that everyone can easily use these lists. This is mostly a mechanical adjustment. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-17ARM: at91sam9x5: enable MCI0 support for 9x5ek board.Wu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-10-15mx25: Fix eSDHC supportBenoît Thébaudeau
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do with mxcmmc. Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx25: Define cpu_eth_init() only if neededBenoît Thébaudeau
The FEC is the only SoC Ethernet support available on i.MX25, so define cpu_eth_init() only for it instead of returning a misleading success code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up clocks APIBenoît Thébaudeau
Use the standard mxc_get_clock() instead of exporting internal functions and using literal constant values. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25 clocks: Fix MXC_FEC_CLKBenoît Thébaudeau
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock. Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG clock, so remove the duplicated code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Define more standard clocksBenoît Thébaudeau
Define AHB, IPG and CSPI clocks. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up clock calculationsBenoît Thébaudeau
Avoid possible overflow in clock calculations, and do not waste calls to lldiv() to divide simple ulongs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Fix decode_pllBenoît Thébaudeau
The MFN bit-field of the PLL registers represents a signed value. See the reference manual. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: add CPU revision 1.2Eric Benard
tested on a MCIMX257CJM4A which now reports : CPU: Freescale i.MX25 rev1.2 at 399 MHz Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15serial: mxs: spl: Remove empty serial_* functions from SPL codeMarek Vasut
Remove the empty bodies from serial_* functions from MXS SPL code. These empty implementations are now in common/serial.c instead so declaring them also in the SPL code would cause a colision once serial multi is enabled unconditionally. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15ARM: prevent misaligned array initsAlbert ARIBAUD
Under option -munaligned-access, gcc can perform local char or 16-bit array initializations using misaligned native accesses which will throw a data abort exception. Fix files where these array initializations were unneeded, and for files known to contain such initializations, enforce gcc option -mno-unaligned-access. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> [trini: Switch to usign call cc-option for -mno-unaligned-access as Albert had done previously as that's really correct] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-04arm: Fixed the offset for the no relocation.Zhong Hongbo
When the u-boot address of destination equal to __start, no relocation. relocation offset(r9) = 0. Signed-off-by: Zhong Hongbo <bocui107@gmail.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-10-03kirkwood: implement kw_sdram_size_adjustGerlando Falauto
Size of the SDRAM chips might differ between any two (otherwise identical) instances of the same board. So add a function kw_sdram_size_adjust() which reads out the current ram size for a given bank, and adjusts the Kirkwood's SDRAM window size register accordingly. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2012-10-03kirkwood: implement kw_sdram_bs_set()Gerlando Falauto
Some boards might be equipped with different SDRAM configurations. When that is the case, CPU CS Window Size Register (CS[0]n Size) should be set to the biggest value through board.cfg file; then its value can be fixed at runtime according to the detected SDRAM size. Therefore, implement kw_sdram_bs_set(). Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Marek Vasut <marex@denx.de> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2012-10-03kirkwood: use c-struct for access to SDRAM addr decode registersHolger Brunck
Remove the defines and do this with a C-struct. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Marek Vasut <marex@denx.de> Acked-By: Prafulla Wadaskar <Prafulla@marvell.com>
2012-09-27ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORKTom Rini
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs. - Remove duplicated code. - Add spl_boot_device() that returns the statically chosen boot device. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-06mx25: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX25 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Matthias Weisser <weisserm@arcor.de>
2012-09-04MX28: Fixup the ad-hoc use of DIGCTL_MICROSECONDSMarek Vasut
Use proper struct-based access for this register in the SPL code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-03edminiv2: orion5x: fix GPIO inits and valuesAlbert ARIBAUD
Orion5x did not actually write GPIO output values or input polarities, and ED Mini V2 had bad or missing values for GPIO settings. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-01atmel: at91sam9x5: fix name error for spiBo Shen
Fix the name error Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01mxs: Convert timeout parameter to 'unsigned int'fabio.estevam@freescale.com
For representing a timeout value, it makes more sense to pass it as 'unsigned int'. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01gpio: add gpio api support to mx27 (v4)trem
The gpio api has been tested on an armadeus apf27. Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mxs: Rename 'mx28_dram_init' to 'mxs_dram_init'Otavio Salvador
The DRAM initialization, after SPL has complete, is exactly the same for all mxs SoCs so we should name it accordinly. The following boards has been changed: * apx4devkit * m28evk * mx28evk * sc_sps_1 Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
2012-09-01mxs: Only build internal Ethernet controller for i.MX28Otavio Salvador
The internal Ethernet controller is only available on i.MX28 processors so it needs to use CONFIG_MX28 guardian to avoid having this code called in others. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-09-01MX28: config: Allow different target generation in elftosb callOtavio Salvador
The elftosb call needs to use a target param specific for i.MX28. This patch allow for later addition of i.MX233. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-09-01mx25: Enable dcacheBenoît Thébaudeau
Now that the main i.MX features work fine with dcache enabled, enabled it by default if CONFIG_SYS_DCACHE_OFF is not defined. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01MX28: Shuffle around the power management codeMarek Vasut
Move some function calls to a more appropriate place, so they're called only when needed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01MX28: Drop the cp15 reconfiguration from SPLMarek Vasut
The SPL doesn't need the CP15 reconfiguration, as that's what the BootROM does for us already. Moreover, when the CP15 is reconfigured and the code returns control to BootROM, the USB boot works no more. Remove the code and allow [1] to work properly as well. [1] http://git.bfuser.eu/?p=marex/mxsldr.git;a=summary Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mxs: Convert sys_proto.h prefixes to 'mxs'Otavio Salvador
The sys_proto.h functions (except the boot modes) are compatible with i.MX233 and i.MX28 so we use 'mxs' prefix for its methods. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: Remove not required include of iomux-mx28.hOtavio Salvador
The iomux-mx28.h include is not required on spl_mem_init.c so it has been droped. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: Remove not required explicit iomux-mx28.h includeOtavio Salvador
The iomux header is included on sys_proto.h so to avoid SoC specific header inclusion. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-09-01davinci, c6x: Always use C version of reset codeTom Rini
We can safely use the same reset code written in C for both Davinci and C6X platforms. In addition the C version of the code is marginally smaller on Davinci. Tested-by: Matt Porter <mporter@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01da8xx/hawkboard: Add support for ohci host controllerSughosh Ganu
Also enable the ohci port on hawkboard. These additions result in an increased u-boot size -- adjust the same accordingly in the board's config. Move the usb header for da8xx platforms under arch-davinci. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-09-01i.MX28: bug fixes in PMU configuration codeStathis Voukelatos
Signed-off-by: Stathis Voukelatos <stathis.voukelatos@linn.co.uk> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com>
2012-09-01MX28: Move the u-boot.bd info CPUDIR/SOCDIRMarek Vasut
This gets us rid of duplication of the same file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mxs: rename mx28.c to mxs.c as it is common to i.MX233 and i.MX28 SoCsOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: Clarify why we poweroff in case of brownout in 5v conflictOtavio Salvador
If VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes unreliable but this wasn't clear on code so a comment has been added to clarify it. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: Reowork SPL to use 'mxs' prefix for methodsOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: prefix register structs with 'mxs' prefixOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01mxs: prefix register acessor macros with 'mxs' prefixOtavio Salvador
As the register accessing mode is the same for all i.MXS SoCs we ought to use 'mxs' prefix intead of 'mx28'. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit (git 2.34.1) at 2025-01-08 05:15:43 +0000