| Age | Commit message (Collapse) | Author |
|---|
|
Replace the custom bit manipulation function sr32() by standard I/O
accessors. A major motivation for this cleanup was the fact, that a
number of calls of that function resulted in 32 bit wide shift
operations on u32 data, which according to the C-ISO/IEC-9899-Standard
provokes undefined behaviour:
6.5.7 Bitwise shift operators
...
If the value of the right operand is negative or is greater
than or equal to the width of the promoted left operand, the
behavior is undefined.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in
that file to prepare complete removal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Conflicts:
arch/arm/cpu/armv7/config.mk
board/ti/am43xx/mux.c
include/configs/am43xx_evm.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
|
|
Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard
Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds
|
|
This patch change the per_clocks_enable() function used in OMAP3
code to enable peripherals clocks. Only required clock should be
activated. So if the board use the uart(x) as a console we need
to activate it. The Board's config should include define to enable
every subsystem that the board use. For a complete list
of affected peripherals, registers CM_FCLKEN_PER and CM_ICLKEN_PER
should be checked.
Right now the bootloader can enable and disable clocks for:
uart(x) using CONFIG_SYS_NS16550
gpio bank (x) using CONFIG_OMAP3_GPIO_X with X = { 2, 3, 4, 5, 6 }
i2c bus using CONFIG_DRIVER_OMAP34XX_I2C.
Not required gptimer(x) and mcbsp(x) for booting are disabled by default and
are not supported by any define.
Their activation need to included in the per_clocks_enable if the
peripheral is included. Not booting board should enable the peripheral
clock connected to their driver
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.
Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.
Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.
Also fix checkpatch warning about alignment.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The processor is hopefully running with M(ega)Hz and not with m(illi)Hz.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
|
|
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
|
|
In order to use SPL boot from OneNAND we should initialize the gpmc.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
|
|
Add check for write protection in omap mmc driver.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Implement driver check for card detection.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
|
|
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
|
|
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
|
|
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954
removed the need for these definitions but missed to remove them.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
|
|
AM35XX specific functions for integrated USB PHY/MUSB IP.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
|
|
When CONFIG_SYS_L2CACHE_OFF is defined we end up with a few warnings
currently. Re-order functions so that we don't have that anymore.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The restore sequence in lowlevel_init was in the wrong order,
causing lr to lose its original value and be set equal to ip
instead. Also, its use of the stack clashes with that of
s_init, so move the s_init call after the restore and turn
it into a tail-optimized branch.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
|
|
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>. Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This detection code doesn't (and can't) do anything currently, so
remove.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
In warm reset conditions on OMAP36xx/AM/DM37xx the rom code
incorrectly sets the DPLL4 clock input divider to /6.5 which
is an invalid value unless the input clock is 13MHz. When a JTAG
emulator is attached, a warm reset is necessary after the emulator
gains control of the process. This results in a loss of serial
output due to the invalid DPLL4 settings.
This patch fixes the issue by resetting the DPLL4 clock input
divider to /1 when the input clock is not 13MHz. AM/DM37x TRM
section 3.5.3.3.3.2.1 specifies that the /6.5 setting is only
used when the input clock is 13MHz.
Signed-off-by: Matt Porter <mporter@ti.com>
|
|
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
We need to setup CS0 and CS1 not CS0 and CS0 again.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Call i2c initialization in spl_board_init only if I2C
is configured for the board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
|
|
Mainline kernel for OMAP3 doesn't enable L2 cache
It expects L2$ to be enabled by ROM-code/bootloader.
Leaving L2$ enabled can be troublesome in cases where
the L2 cache is not under CP15 control, such as in
Cortex-A9. This problem is explained in detail in
the commit dc7100f4080952798413fb63bb4134b22c57623a
However, this problem doesn't apply to Cortex-A8
because L2$ in Cortex-A8 is under CP15 control and
hence the generic armv7 maintenance opertions work
for it.
As such we can make an exception for OMAP3 and
leave the L2$ enabled when we jump to kernel. This
is done by removing the strongly-linked implementation
of v7_outer_cache_disable() and allowing it to fall
back to the weakly linked implementation that doesn't
do anything.
Signed-off-by: Aneesh V <aneesh@ti.com>
|
|
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
|
|
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
|
|
The function get_sdr_cs_offset reads the CS_CFG register in the SDRC
to determine where CS1 is mapped to. make_cs1_contiguous() will set
CS1 to follow after CS0. The CS_CFG register has values in bits 9:8
and 3:0 but we had erroneously been testing 5:4 and 3:0 resulting in
incorrect offsets on platforms with less than 128MB as 3:0 describe
128MB hunks and 9:8 describe 32MB offsets after the 128MB hunk.
Tested-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Wrap the function save_boot_params with CONFIG_SPL_BUILD. This will
allow non-SPL boards to define their own save_boot_params functions
in U-Boot itself.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
|
|
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
|
|
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this function
weak.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
