| Age | Commit message (Collapse) | Author |
|---|
|
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.
This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.
Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.
Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.
For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
We do not use irqs in u-boot so remove the unused irq field, and all the
#ifdef-ery around the irq initialization.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.
Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.
For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.
In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
