summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7
AgeCommit message (Collapse)Author
2014-07-01Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-07-01Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-30Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-25Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-25Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-19OMAP: disable gpmc timeout safely for reenablingStefano Babic
gpmc timeout is disabled and the reset counter is set to 0. However, if later a driver activates the timeout setting the reset to a valid value, the old reset value with zero is still valid for the first access. In fact, the timeout block loads the reset counter after a successful access. Found on a am335x board with a FPGA connected to the GPMC bus together with the NAND. When the FPGA driver in kernel activates the timeout, the system hangs at the first access by the NAND driver. Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-19omap3: board: trivial: add void for no argsJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-19cpu: armv7: am33x: ddr: write emif ref_ctrl_shadow registerFelipe Balbi
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19ARM: keystone: aemif: move aemif driver to drivers/memory/ti-aemif.cKhoronzhuk, Ivan
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-06-19mtd: nand: davinci: add header file for driver definitionsKhoronzhuk, Ivan
The definitions inside emif_defs.h concern davinci nand driver and should be in it's header. So create header file for davinci nand driver and move definitions from emif_defs.h and nand_defs.h to it. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> [trini: Fixup more davinci breakage] Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19omap: Don't enable GPMC CS0 with nothing attachedAsh Charles
If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set for GPMC on chip select #0---size is 0. In this case, the GPMC configuration should be reset but not enabled. Enabling causes the Gumstix DuoVero board to hang when entering Linux. Signed-off-by: Ash Charles <ashcharles@gmail.com> [trini: Switch to testing base as GPMC_SIZE_256M is 0x0] Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19tegra20: display: fix checking of return valueJeroen Hofstee
The calling code seems a bit in doubt about the return value of fdtdec_lookup_phandle. Since it returns a negative value on error (and fdt_node_offset_by_phandle as well), check for that. cc: Wei Ni <wni@nvidia.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-06-17imx: correct HAB status for new chip TOStefano Babic
According to: http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0 ENGR00287268 mx6: fix the secure boot issue on the new tapout chip commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b newer i.MX6 silicon revisions have an updated ROM and HAB API table. Please see also: i.MX Applications Processors Documentation Engineering Bulletins EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison With this change the secure boot status is correctly displayed Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-17arm: zynq: fix a bug in Zynq linker scriptMasahiro Yamada
Commit 41623c91 moved exception handlers to ".vectores" section but it missed to adjust Zynq linker script. Zynq boards hang up after relocation because "_start" symbol does not point to the correct address and gd->relocaddr gets insane. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Tested-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-06-14ARMv7: at91: enable ICache and DCache.Wu, Josh
For at91 armv7 SoC (SAMA5D3x), only LCD and macb used DMA. Now as the lcd and macb driver already support dcache. So we can enable dcache now. Also we can enable icache without any problem. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-06-11cosmetic: Whitespace fixVasili Galka
Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-06-11am33xx/omap: Allow cache enable for all Sitara/OMAPSimon Glass
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined. This speeds up the Beaglebone Black boot considerable. (Tested only on Beaglebone Black with SD card boot) Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-06arm:am33xx: Add a scale_vcores() hookTom Rini
Similar to OMAP4/5 we need to scale the voltage up prior to changing the clock frequencies up higher. Add a similar hook to start with. Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06ARM: AM43xx: Fix UART clocks enablingLokesh Vutla
After enabling a module, SW has to wait on IDLEST bit until it is Fully functional. This wait is missing for UART module and there is a immediate access of UART registers after this. So there is a chance of hang on this module( This can happen when we are running from MPU SRAM). So waiting for IDLEST bit. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-06-06keystone: init: enable UART1 to be able use it from kernelMurali Karicheri
Currently PWREMU_MGMT is not configured in the Linux generic UART driver as this register seems to be specific TI UART IP. So this needs to be enabled in u-boot to use UART1 from kernel space. Acked-By: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-06-06arm:am33xx: Rework s_init and add board_early_init_fTom Rini
With the changes to the i2c framework (and adopting the omap24xx_i2c driver to them) we can no longer call i2c functions prior to gd having been set and cleared. When SPL booting, this is handled by setting gd to point to SRAM in s_init. However in the cases where we are loaded directly by ROM (memory mapped NOR or QSPI) we need to make use of the normal hooks to slightly delay these calls. Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06arm:am33xx: Make dram_init call sdram_init() in some contextsTom Rini
We have two contexts for booting these platforms. One is SPL which is roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main, board_init_f from SPL, ... then U-Boot loads. The other is a memory-mapped XIP case (NOR or QSPI) where we do not run an SPL. In this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init, _main, regular board_init_f. In the first case s_init will set a valid gd and then be able to call sdram_init which in many cases will need i2c (which needs a valid gd for gd->cur_i2c_bus). In this second case we must (and are able to and should) defer sdram_init() into dram_init() called by board_init_f as gd will have been set in _main and cleared in board_init_f. Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06am43xx_evm: Add qspiboot targetSourav Poddar
The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot target that utilizes QSPI for env and so forth as an example of best practices. As QSPI is booted from directly we need to chang CONFIG_SYS_TEXT_BASE. Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices we need to handle that elsewhere, once NAND support is also added. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and ↵pekon gupta
GPMC_NAND_ECC_LP_x16_LAYOUT OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros to configure GPMC controller for x7 or x8 bit device connected to its interface. Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above macros can be completely removed. Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06mx6: add mmdc configuration for MX6Q/MX6DLTim Harvey
- add function for configuring iomux based on board-specific regs - add function for configuring mmdc based on board-specific and chip-specific data Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-02Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-31Exynos: Make sure ps_hold gets set in the SPLDoug Anderson
Setting ps_hold ought to be one of the first things we do when we first boot up. If we wait until the main u-boot runs we won't set it in time and the PMIC may power us back off. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-28exynos: Enable PSHOLD in SPLSimon Glass
There is quite a tight deadline in enabling PSHOLD, less than a second. In some cases (e.g. with USB download), U-Boot takes longer than that to load, so the board powers off before U-Boot starts. Add a call in SPL to enable PSHOLD. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-27arm:at91: enable ROM loadable atmel imageAndreas Bießmann
For sama5d3xek we need to modify the SPL image for correct detection by ROM code. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Tested-by: Bo Shen <voice.shen@atmel.com>
2014-05-25sunxi: non-FEL SPL boot support for sun7iIan Campbell
Add support for booting from an MMC card. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25sunxi: add gmac Ethernet supportIan Campbell
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i) processors. Enable for the Cubietruck. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25sunxi: add sun7i cpu, board and start of day supportIan Campbell
This patch adds generic board, start of day and basic build system support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luc Verhaegen <libv@skynet.be> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Patrick Wood <patrickhwood@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25sunxi: add sun7i dram setup supportIan Campbell
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25sunxi: add sun7i pinmux and gpio supportIan Campbell
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ma Haijun <mahaijuns@gmail.com> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25sunxi: add sun7i clocks and timer support.Ian Campbell
This patch adds the basic clocks and timer support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Some of the code here is common to multiple sunxi subarchtectures, hence files are named sun4i which is the earliest similar variant. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-05-24Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-23am33xx: report silicon revision instead of codeSergey Alyoshin
As revision code 1 is for silicon revision 2.0, it is easily confused with silicon revision 1.0. Device type report also reworked in same style. Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
2014-05-23ARM: OMAP: Fix omap_sdram_size calculationLokesh Vutla
Last section of DMM is used for trapping tiler unmapped sections. Corresponding trap_size should be deducted from total SDRAM size only if trap section is overlapping with available SDRAM based on DMM sections. Fixing the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_contextTom Rini
The omap_hw_init_context function (and assorted helpers) is the same for all OMAP-derived parts as when CHSETTINGS are used, that's the same and our DDR base is also always the same. In order to make this common we simply need to update the names of the define for DDR address space which is also common. Cc: Sricharan R. <r.sricharan@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23ARM: DRA7xx: ctrl: Fix efuse register addressesLokesh Vutla
Efuse register addresses are wrongly programmed. Fixing the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-23ARM: DRA72x: Update EMIF dataLokesh Vutla
DRA72 has 1GB connected to EMIF1 only. Updating the details. And also enable WA for BUG0039 only if corresponding EMIF is present. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-23ARM: DRA72x: clocks: Update the hwdataLokesh Vutla
Adding the prcm, dplls, control module hooks for DRA72x. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-23ARM: DRA72x: volt: Update the pmic offsetsKeerthy
TPS65917 is used in DRA722 evm. Update the address offsets accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-23ARM: DRA72x: Add Silicon ID supportLokesh Vutla
Add silicon ID code for DRA722 silicon. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-23ARM: omap: merge GPMC initialization code for all platformpekon gupta
GPMC controller on TI's OMAP SoC is general purpose controller to interface with different types of external devices like; - parallel NOR flash - parallel NAND flash - OneNand flash - SDR RAM - Ethernet Devices like LAN9220 Though GPMC configurations may be different for each platform depending on clock-frequency and external device interfacing with controller. But initialization sequence remains common across all platfoms. Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c files into single omap-common/mem-common.c However, actual platforms specific register config values are still sourced from corresponding platform specific headers like; AM33xx: arch/arm/include/asm/arch-am33xx/mem.h OMAP3: arch/arm/include/asm/arch-omap3/mem.h OMAP4: arch/arm/include/asm/arch-omap4/mem.h OMAP4: arch/arm/include/asm/arch-omap5/mem.h Also, CONFIG_xx passed by board-profile decide config for which set of macros need to be used for initialization CONFIG_NAND: initialize GPMC for NAND device CONFIG_NOR: initialize GPMC for NOR device CONFIG_ONENAND: initialize GPMC for ONENAND device Signed-off-by: Pekon Gupta <pekon@ti.com> [trini: define GPMC_SIZE_256M for omap3] Signed-off-by: Tom Rini <trini@ti.com>
2014-05-23Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-23Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-21arm: rmobile: r8a7791: Fix MOD_SEL3 function table about FN_SEL_IEBNobuhiro Iwamatsu
FN_SEL_IEB is assigned 2bit, and 2bit can represent 4 patterns. However FN_SEL_IEB but we only use 3. It adds empty patterns as 0. Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-16Merge remote-tracking branch 'u-boot-sh/rmobile'Albert ARIBAUD
Conflicts: boards.cfg Trivial conflict, maintainer change plus board addition
2014-05-16ARM: exynos: clock: modify the set_mmc_clk for exynos4Jaehoon Chung
Modified the mmc_set_clock for eynos4. The goal of this patch is that fsys-div register should be reset. And retore the div-value, not using the value of lowlevel_init. (For using SDMMC4, this patch is needs) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit (git 2.34.1) at 2024-12-29 19:43:04 +0000