| Age | Commit message (Collapse) | Author |
|---|
|
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
SGX clocks should be enabled only for OMAP5 ES1.0.
So this can be removed.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.
Add .prm_rsttime address init to the ES1.0 struct.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
|
|
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
|
|
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:
* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
performance at the cost of power. Used to operate safely at high
OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
save power. Used to save power at lower OPPs.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
|
|
Conflicts:
drivers/serial/Makefile
|
|
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Only called in this file, mark as static.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
|
|
Conflicts:
drivers/mtd/nand/mxc_nand_spl.c
include/configs/m28evk.h
|
|
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Currently save_boot_params saves the boot parameters passed
from romcode. But this is not stored in a writable location
consistently. So the current code would not work for a
'XIP' boot. Change this by saving the boot parameters in
'gd' which is always writable. Also add a 'C' function
instead of an assembly code that is more readable.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
|
|
These defines are same across OMAP4/5. So move them to
omap_common.h. This is required for the patches that
follow.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
|
|
The arm_freq and ddr_freq variables are unused, so remove. Fixup
whitespace slightly while in here.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
|
|
USB TLL clocks do not support 'explicit_en', only 'hw_auto'
control (R. Sricharan). cm_l3init_hsusbtll_clkctrl has to be
moved to the clk_modules_hw_auto_essential[] array in order
to make the clock work.
This fix is needed (but not sufficient) for USB EHCI operation
in U-Boot.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
|
|
EMIF supports a global warm reset mode, during which the
EMIF keeps the SDRAM content. But if leveling is enabled
at the time of warm reset for DDR3, the following steps
needs to be done after warm reset:
1) Keep EMIF in self refresh mode.
2) Reset PHY to bring back the PHY to a known state.
3) Start Levelling procedure.
Doing the same.
And also enabling DLL lock and code output after warm reset.
Tested on OMAP5432 ES2.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
I2C4 and I2C5 are utilized on all known OMAP5 hardware platforms.
The i2c5 clock was however not enabled; do this here.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
|
|
Enables required PLLs and clocks for CPSW on TI814x.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Augment the MX5 clock code with function to enable and configure
NFC clock. This is necessary to get NFC working on MX5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
|
|
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Move baseaddr to hardware.h to be shared between
configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Rework the __udelay function of U-Boot Zynq Arch to handle
delay < 1000 usec
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Add an mxc_ocotp driver for i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
IIM:
- Homogenize prg_p naming (the reference manuals are not always self-consistent
for that).
- Add missing SCSx and bank registers.
- Fix the number of banks on i.MX53.
OCOTP:
- Rename iim to ocotp in order to avoid confusion.
- Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
reference manual.
- Merge the existing spinoff gp1 fuse definition on i.MX6.
- Fix the number of banks on i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
When booting a FSL kernel based on 2.6.35 it is necessary to pass the revision
tag to the kernel.
Place a common weak function into soc.c for such purpose.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx6 solo-lite is another member of the mx6 series.
For more information about mx6 solo-lite, please visit:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX6SL&nodeId=018rH3ZrDRB24A
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
The current code is causing errors like this on my toolchains:
/usr/x86_64-pc-linux-gnu/armv7a-cros-linux-gnueabi/binutils-bin/2.22/
ld.bfd.real: failed to merge target specific data of file /usr/lib/gcc/
armv7a-cros-linux-gnueabi/4.7.x-google/libgcc.a(_divdi3.o)
Use do_div() to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
A start vector fix was added by AneeshV for OMAP4 (commit 0d479b53),
and caused the old monilithic Tegra builds to hang due to an undefined
instruction trap. Previously, the code needed to run on both the
AVP (ARM7TDI) and A9, and the AVP doesn't have a CP15 register.
I corrected this in commit 6d6c0bae w/#ifndef CONFIG_TEGRA, but
now that we use SPL, and boot the AVP w/o any ARMv7 code, I can
revert my change, and make Aneesh's change apply to Tegra.
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The KVM and Xen hypervisors for the Cortex-A15 virtualization
implementation need to be entered in HYP mode. Should the primary
board firmware already enter HYP mode (Calxeda firmware does that),
we should not deliberately drop back to SVC mode.
Since U-boot does not use the MMU, running in HYP mode is just fine.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
|
|
When swi instruction is executed, it is expected to get message
"software interrupt" in console and dump registers and reboot, as
do_software_interrupt() in arch/arm/lib/interrupts.c.
But, actually it causes data abort accessing wrong address in get_bad_stack_swi
macro in arch/arm/cpu/v7/start.S.
This patch fixes this problem.
The same mistake in arch/arm/cpu/{arm1136,arm1176,pxa}/start.S.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
|
|
The processor is hopefully running with M(ega)Hz and not with m(illi)Hz.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
|
|
|
|
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL'
(i.e. imx header + u-boot-spl.bin) make targets for all imx processors
supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations
were missing.
At the same time, fix the build of SPL targets not supporting the imx header on
arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if
CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without
an imx header.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.
This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
