summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7
AgeCommit message (Collapse)Author
2012-07-07OMAP5: ADD chip detection for OMAP5432 SOCLokesh Vutla
This patch adds chip detection for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07ARM: OMAP5: Align memory used for testing to the power of 2SRICHARAN R
get_ram_size checks the given memory range for valid ram, but expects the size of memory to be aligned to the power of 2. In case of OMAP5 evm board the memory available is 2GB - 16MB(used for TRAP section) = 2032MB. So always ensure that the size of memory used for testing is aligned to the power of 2. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07ARM: OMAP5: dmm: Create a tiler trap section.SRICHARAN R
The unmapped entries in tiler space are set with values 0xFF. So creating a DMM section of size 16MB at 0xFF000000 with ADDRSPACE set to 0x2. This way all the unmapped entry accesses to tiler will be trapped by the EMIF and a error response is sent to the L3 interconnect. L3 errors are inturn reported to MPU. Note that here the tiler trap section is overlapping with the actual ddr physical space and we lose 16MB out of the total 2GB. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07ARM: OMAP4+: dmm: Take care of overlapping dmm and trap sections.SRICHARAN R
The DMM sections can be overlapping with each other, with sections 3 to 0 having the highest to lowest priority in that order. There could also be a section that is used trap the unmapped Tiler entries and this trap section could be overlapping with the actual sdram area. So take care of the above scenarios while calculating the size of the actual ram. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07am33xx: Do not call init_timer twiceTom Rini
We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07arm: Tegra: Use ODMDATA from BCT in IRAMTom Warren
Walk the BIT and BCT to find the ODMDATA word in the CustomerData field and put it into Scratch20 reg for use by kernel, etc. Built all Tegra builds OK; Booted on Seaboard and saw ODMDATA in PMC scratch20 was the same as the value in my burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities will have to specify the odmdata (nvflash --odmdata n) on the command line or via a cfg file, or built in to their BCT. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2012-07-07tegra: override compiler flags for low level init codeamartin@nvidia.com
Override -march setting for tegra to -march=armv4t for files that are necessary for low level init on tegra. The recent change to use -march=armv7-a for armv7 caused a regression on tegra because tegra starts boot on a arm7tdmi processor before transferring control to the cortex-a9. While still executing on the arm7tdmi there are calls to getenv_ulong() and memset() that cause an illegal instruction exception if compiled for armv7. Signed-off-by: Allen Martin <amartin@nvidia.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: Correct PLL access in ap20.c and clock.cSimon Glass
Correct this warning seen by Albert: ap20.c:44:18: warning: array subscript is above array bounds There is a subtle bug here which currently causes no errors, but might in future if people use PCI or the 32KHz clock. So take the opportunity to correct the logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: add SDMMC1 on SDIO1 funcmux entryStephen Warren
This will be used on TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: add SDIO1 funcmux entry for UARTALucas Stach
This is based on top of: tegra: add alternate UART1 funcmux entry tegra: add UART1 on GPU funcmux entry v2: remove enum change Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> CC: Marek Vasut <marex@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: add UART1 on GPU funcmux entryStephen Warren
TrimSlice uses UART1 on the GPU pingroup. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: add alternate UART1 funcmux entryStephen Warren
(In at least some configurations) Whistler uses UART1 on pingroups UAA, UAB. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xxMatt Porter
In warm reset conditions on OMAP36xx/AM/DM37xx the rom code incorrectly sets the DPLL4 clock input divider to /6.5 which is an invalid value unless the input clock is 13MHz. When a JTAG emulator is attached, a warm reset is necessary after the emulator gains control of the process. This results in a loss of serial output due to the invalid DPLL4 settings. This patch fixes the issue by resetting the DPLL4 clock input divider to /1 when the input clock is not 13MHz. AM/DM37x TRM section 3.5.3.3.3.2.1 specifies that the /6.5 setting is only used when the input clock is 13MHz. Signed-off-by: Matt Porter <mporter@ti.com>
2012-05-15omap4: do not enable auxiliary coresTero Kristo
Booting up these cores (dsp / ivahd / cortex-m3) is bad without firmware running on them, and they will hang preventing any kind of sleep transitions later on with the kernel. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: R Sricharan <r.sricharan@ti.com>
2012-05-15omap4: do not enable fs-usb moduleTero Kristo
If this is done in the bootloader, the FS-USB will later be stuck into intransition state, which will prevent the device from entering idle. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2012-05-15tegra2: trivially enable 13 mhz crystal frequencyLucas Stach
This is needed for upcoming Toradex Colibri T20 upstream support. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add keyboard support to funcmuxSimon Glass
Add funcmux support for the default keyboard mapping. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Setup PMC scratch info from ap20 setupYen Lin
Save SDRAM parameters into the warmboot scratch registers Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Yen Lin <yelin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add warmboot implementationYen Lin
Add code to set up the warm boot area in the Tegra CPU ready for a resume after suspend. Signed-off-by: Yen Lin <yelin@nvidia.com> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add PMU to manage power suppliesJimmy Zhang
Power supplies must be adjusted in line with clock frequency. This code provides a simple routine to set the voltage to allow operation at maximum frequency. - Split PMU code into separate TPS6586X driver Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add EMC support for optimal memory timingsJimmy Zhang
Add support for setting up the memory controller parameters. Boards can set up an appropriate table in the device tree. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add tegra_get_chip_type() to detect SKUSimon Glass
We want to know which type of chip we are running on - the Tegra family has several SKUs. This can be determined by reading a fuse register, so add this function to ap20. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add crypto library for warmboot codeYen Lin
Provides an interface to aes.c for the warmboot code. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Yen Lin <yelin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Add functions to access low-level Osc/PLL detailsSimon Glass
Add clock_ll_read_pll() to read PLL parameters and clock_get_osc_bypass() to find out if the Oscillator is bypassed. These are needed by warmboot. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15tegra: Move ap20.h header into arch locationSimon Glass
We want to include this from board code, so move the header into an easily-accessible location. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15Add abs() macro to return absolute valueSimon Glass
This macro is generally useful to make it available in common. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15i.MX6: add enable_sata_clock()Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15i.MX6: Add ANATOP regulator initDirk Behme
Init the core regulator voltage to 1.2V. This is required for the correct functioning of the GPU and when the ARM LDO is set to 1.225V. This is a workaround to fix some memory clock jitter. Note: This should be but can't be done in the DCD. The bootloader prevents access to the ANATOP registers. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Chen <b02280@freescale.com> CC: Jason Liu <r64343@freescale.com> CC: Ranjani Vaidyanathan <ra5478@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <festevam@gmail.com>
2012-05-15mx53loco: Allow to print CPU information at a later stageFabio Estevam
Print CPU information within board_late_init(). This is in preparation for adding 1GHz support, which requires programming a PMIC via I2C. As I2C is only available after relocation, print the CPU information later at board_late_init(), so that the CPU frequency can be printed correctly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15mx5: Add clock config interfaceFabio Estevam
mx5: Add clock config interface Add clock config interface support, so that we can configure CPU or DDR clock in the later init Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15imx-common: Factor out get_ahb_clk()Fabio Estevam
get_ahb_clk() is a common function between mx5 and mx6. Place it into imx-common directory. Cc: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX53: add function to set SATA clock to internalStefano Babic
The MX53 SATA interface can use an internal clock (USB PHY1) instead of an external clock. This is an undocumented feature, but used on most Freescale's evaluation boards, such as MX53-loco. As stated by Freescale's support: Fuses (but not pins) may be used to configure SATA clocks. Particularly the i.MX53 Fuse_Map contains the next information about configuring SATA clocks : SATA_ALT_REF_CLK[1:0] (offset 0x180C) '00' - 100MHz (External) '01' - 50MHz (External) '10' - 120MHz, internal (USB PHY) '11' - Reserved Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX5: Add definitions for SATA controllerStefano Babic
Add base address and MXC_SATA_CLK to return the clock used for the SATA controller. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15EXYNOS: add LCD and MIPI DSI clock interface.Donghwa Lee
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: definitions of system resgister and power management registers.Donghwa Lee
This is definitions of system registers and power mananagement registers for EXYNOS SoC. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15omap3: Introduce weak misc_init_rTom Rini
Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15omap4+: Remove CONFIG_ARCH_CPU_INITTom Rini
OMAP4/5 had an empty arch_cpu_init() so drop that along with CONFIG_ARCH_CPU_INIT Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15armv7: Use -march=armv7-a and thereby enable Thumb-2Aneesh V
Enable -march=armv7-a for armv7 platforms if the tool-chain supports it. This in turn results in Thumb-2 code generated for these platforms if CONFIG_SYS_THUMB_BUILD is enabled. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15armv7: add appropriate headers for assembly functionsAneesh V
Use ENTRY and ENDPROC with assembly functions to ensure necessary assembler directives for all functions. Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15OMAP5: reset: Use cold reset in case of 5430ES1.0SRICHARAN R
Warm reset is not functional in case of omap5430ES1.0. So override the weak reset_cpu function to use cold reset instead. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP3+: reset: Create a common reset layer.SRICHARAN R
The reset.S has the function to do a warm reset on OMAP based socs. Moving this to a reset.c file so that this acts a common layer to add any reset related functionality for the future. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15arm: omap5: correct boot device mode7 for eMMCBalaji T K
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP5: ddr: Change the ddr device name.SRICHARAN R
The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and not a ELPIDA part. So change this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: device: Add support to get the device type.SRICHARAN R
Add support to identify the device as GP/EMU/HS. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the sysctrl structure commonSRICHARAN R
Make the sysctrl structure common, so that it can be used in generic functions across socs. Also change the base address of the system control module, to include all the registers and not simply the io regs. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the silicon revision variable common.SRICHARAN R
The different silicon revision variable names was defined for OMAP4 and OMAP5 socs. Making the variable common so that some code can be made generic. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: hwinit: Add the missing break statementSRICHARAN R
The break statement is missing in init_omap_revision function, resulting in a wrong revision identification. So fixing this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: palmas: Configure nominal opp vdd valuesSRICHARAN R
The nominal opp vdd values as recommended for ES1.0 silicon is set for mpu, core, mm domains using palmas. Also used the right sequence to enable the vcores as per a previous patch from Nishant Menon, which can be dropped now. http://lists.denx.de/pipermail/u-boot/2012-March/119151.html Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.SRICHARAN R
The OMAP5 silicon has new DDR PHY design, which includes a external PHY as well. So configuring the ext PHY parameters here. Also the EMIF timimg registers and a couple of DDR mode registers needs to be updated based on the testing from the actual silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: io: Configure the io settings for omap5430 sevm board.SRICHARAN R
The control module provides options to set various signal integrity parameters like the output impedance, slew rate, load capacitance for different pad groups. Configure these as required for the omap5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
generated by cgit (git 2.34.1) at 2025-01-08 16:03:56 +0000