summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
AgeCommit message (Collapse)Author
2011-09-04omap3:clock: check cpu_family before enabling clks for IVA & CAMVaibhav Hiremath
In case of AM3517 and AM3505 (which is OMAP3 varients), IVA2 and ISP-CAMERA modules have been removed. So add check for cpu_family before enabling clocks for these modules, else this impacts subsequent power consumption and system suspend/resume functionality. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04omap3:clock: configure GFX clock to 200MHz for AM/DM37xVaibhav Hiremath
AM/DM37x is another OMAP3 variant, where the GFX clock has been boosted to 192MHz/200MHz. So fix the GFX_DIV value for this change. HW Errata: Due to dependency of TV out clock of 54MHz, it is not possible to configure GFX to 192MHz. So as per HW errats, the recommended GFX clock is 200MHz (=CORE_CLK/2). Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04armv7: cache: remove flush on un-aligned invalidateAneesh V
Remove the flush of boundary cache-lines done as part of invalidate on a non cache-line boundary aligned buffer Also, print a warning when this situation is recognized. Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04armv7: stronger barrier for cache-maintenance operationsAneesh V
set-way operations need a DSB after them to ensure the operation is complete. DMB may not be enough. Use DSB after all operations instead of DMB. Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04omap: enable caches at system start-upAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04Tegra2: Use clock and pinmux functions to simplify codeSimon Glass
Signed-off-by: Simon Glass <sjg@chromium.org>
2011-09-04Tegra2: Add additional pin multiplexing featuresSimon Glass
This adds an enum for each pin and some functions for changing the pin muxing setup. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-09-04Tegra2: Add more clock supportSimon Glass
This adds functions to enable/disable clocks and reset to on-chip peripherals. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-09-04Tegra2: Add microsecond timer functionSimon Glass
These functions provide access to the high resolution microsecond timer and tidy up a global variable in the code. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-09-04MX: MX35 / MX5: uniform clock command with powerpcStefano Babic
There was already a command to show the processor clocks for PowerPC (clocks). For i.MX, the "clockinfo" command was introduce. The patch sets the same command name used on PowerPC. A nasty and not needed newline is also dropped in the help for the command. Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-09-04ARM: MX51: PLL errata workaroundDavid Jander
This is a port of the official PLL errata workaround from Freescale to mainline u-boot. The PLL's in the i.MX51 processor can go out of lock due to a metastable condition in an analog flip-flop when used at high frequencies. This workaround implements an undocumented feature in the PLL (dither mode), which causes the effect of this failure to be much lower (in terms of frequency deviation), avoiding system failure, or at least decreasing the likelihood of system failure. Signed-off-by: David Jander <david@protonic.nl>
2011-09-04omap: fix gpio related build breaksAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2011-09-03integrator: convert to new build systemLinus Walleij
This deletes the integrator split_by_variant.sh script and defines a number of unique board types for the core modules that are meaningful to support for the Integrator AP/CP, i.e. the ones that did not just say "unsupported core module" in split_by_variant.sh. If more core modules need to be supported they are easy to add. We delete all the old cruft in Makefile and MAKEALL that was working around the old way of building boards. We create a unique config file per board to satisfy the build system, but they are just oneliners that include the existing integratorap.h and integratorcp.h configs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-09-03atmel: update at91sam9m10g45 SoC support to new styleThomas Petazzoni
Based on earlier work by Alex Waterman <awaterman@dawning.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2011-08-04Convert ISO-8859 files to UTF-8Albert ARIBAUD
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source tree, which could cause issues with the patchwork review system. This commit converts all ISO-8859 files to UTF-8. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-08-04arm: auto gen asm-offsets.h for mb86r0xMatthias Weisser
auto gen asm-offsets.h for mb86r0x Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-08-03AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/masterXu, Hong
Rework for AT91SAM9263 SoC, makes it build again. Based on the work for AT91SAM9260-EK. Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
2011-08-03AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/masterXu, Hong
Rework for AT91SAM9RL SoC, makes it build again. Based on the work for AT91SAM9260-EK. V4: US->USART, cosmetics Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03AT91: change common at91sam9261 files to compile with new schemeAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at> Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)Reinhard Meyer
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USARTAndreas Bießmann
The CONFIG_AT91RM9200_USART is an remnant of 18ed5e9550810e2fc5bf2c757aee47774609651c which deleted the at91rm9200_usart driver. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-08-03a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warningAndreas Bießmann
The CONFIG_AT91_LEGACY warning became obsolete due to complete removal of at91rm9200 arch code in arm920t. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-08-03ARM: remove obsolete at91rm9200Andreas Bießmann
The big "ARM: remove broken boards" series deletes all boards using obsolete arm920t/at91rm9200 arch code. Therefore we can safely remove this code now. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-08-03omap4: clock init support for omap4460Aneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: support TPS programmingAneesh V
TPS62361 is the new power supply used in OMAP4460 that supplies vdd_mpu. VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies vdd_iva. VCORE3 is not used in OMAP4460. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap: reuse omap3 gpio support in omap4Aneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: sdram init changes for omap4460Aneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: add omap4460 revision detectionAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03mkimage: Add OMAP boot image supportJohn Rigby
- Add mkimage support for OMAP boot image - Add support for OMAP boot image(MLO) generation in the new SPL framework Signed-off-by: John Rigby <john.rigby@linaro.org> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap: add MMC and FAT support to SPLAneesh V
- Add MMC raw and FAT mode boot support for OMAP - Provide a means by which parameters passed by ROM-code can be saved in u-boot. - Save boot mode related information passed by OMAP4 ROM-code and use it to determine where to load the u-boot from - Assumes that the image has a mkimage header. Gets the payload size and load address from this header. If the header is not detected assume u-boot.bin as payload Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap: add basic SPL supportAneesh V
- Provide alternate implementations of board_init_f() board_init_r() for OMAP spl. - Provide linker script - Initialize global data - Add serial console support - Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move it to board config header from config.mk Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03armv7: start.S: fixes and enhancements for SPLAneesh V
- Allow SPL to have .bss disjoint from rest of the image - Allow for .bss setup in CONFIG_SPL_BUILD case too. - Take care of the special case where relocation offset = 0. - Compile out exception handling code and install a simpler vector Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: automatic sdram detectionAneesh V
Identify SDRAM devices connected to EMIF automatically: LPDDR2 devices have some Mode Registers that provide details about the device such as the type, density, bus width etc. EMIF has the capability to read these registers. If there are no devices connected to a given chip-select reading mode registers will return junk values. After reading as many such registers as possible and matching with expected ranges of values the driver can identify if there is a device connected to the respective CS. If we identify that a device is connected the values read give us complete details about the device. This along with the base AC timings specified by JESD209-2 allows us to do a complete automatic initialization of SDRAM that works on all boards. Please note that the default AC timings specified by JESD209-2 will be safe for all devices but not necessarily optimal. However, for the Elpida devices used on Panda and SDP the default timings are both safe and optimal. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: calculate EMIF register valuesAneesh V
Calculate EMIF register values based on AC timing parameters from the SDRAM datasheet and the DDR frequency rather than using the hard-coded values. For a new board the user doen't have to go through the tedious process of calculating the register values. Instead, just provide the AC timings from the device data sheet as input and the driver will automatically calculate the register values. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: add sdram init supportAneesh V
Add support for the SDRAM controller (EMIF). Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: add clock supportAneesh V
Add support for: 1. DPLL locking 2. Initialization of clock domains and clock modules 3. Setting up the right voltage on voltage rails This work draws upon previous work done for x-loader by: Santosh Shilimkar <santosh.shilimkar@ti.com> Rajendra Nayak <rnayak@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: add OMAP4430 revision checkAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap4: cleanup pin mux dataAneesh V
- separate mux settings into essential and non essential parts - essential part is board independent as of now(so move it to SoC directory). Will help in having single SPL for all boards. - Non-essential part(the pins not essential for u-boot to function) need to be phased out eventually. - Correct mux data by aligning to the latest settings in x-loader Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03omap3: Include array definition only when it is usedSanjeev Premi
The array of strings corresponding to cpu revision is used only when CONFIG_DISPLAY_CPUINFO is selected - in the function print_cpuinfo(). Enclose definition of this array in #ifdef...#endif for the same. Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-07-28cleanup: Fix typos and misspellings in various files.Mike Williams
Recieve/Receive recieve/receive Interupt/Interrupt interupt/interrupt Addres/Address addres/address Signed-off-by: Mike Williams <mike@mikebwilliams.com>
2011-07-26Timer: Remove reset_timer_masked()Graeme Russ
In some circumstances, reset_timer_masked() was called be timer_init() in order to perform architecture specific timer initialisation. In such cases, the required code in reset_timer_masked() has been moved into timer_init()
2011-07-26Timer: Fix at91rm9200/spi.c timer usageGraeme Russ
2011-07-26Timer: Remove reset_timer() for non-Nios2 archesGraeme Russ
2011-07-26Timer: Remove set_timer completelyGraeme Russ
2011-07-26replace CONFIG_PRELOADER with CONFIG_SPL_BUILDAneesh V
replace all occurences of CONFIG_PRELOADER with CONFIG_SPL_BUILD Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-18ARM: MX5: Fix broken leftover TO-2 errata workaroundDavid Jander
This check was broken. r3 does not contain the silicon revision anymore, so we need to reload it. Also, this errata only applies to i.MX51. Signed-off-by: David Jander <david@protonic.nl> Acked-by: Stefano Babic <sbabic@denx.de>
2011-07-18MX31: Cleanup clock functionStefano Babic
The patch provide the same API used with other i.MX processors and get rid of mx31_ functions. Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-07-17Remove volatile qualifier in get_ram_size() callsAlbert ARIBAUD
Checkpatch.pl complains about the volatile qualifier in calls to get_ram_size(). Remove this qualifier in the prototype and in the calls where it is useless, and leave it only in the function body where it is needed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-17ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7Rob Herring
cpu_init_crit can be skipped, but the code is still enabled requiring a platform to supply lowlevel_init. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Albert ARIBAUD <albert.aribaud@free.fr>
2011-07-14MX27: Update to autogenerated asm-offsets.hStefano Babic
On i.MX27, the asm-offsets.h file is not yet generated as it should be. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Matthias Weisser <weisserm@arcor.de>
generated by cgit (git 2.34.1) at 2025-01-02 19:59:24 +0000