| Age | Commit message (Collapse) | Author |
|---|
|
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Update Clock settings and CCM register map for i.MX6ULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Adjust POR_B settings on i.MX6ULL according to IC design
team's suggestion:
2'b00 : always PUP100K
2'b01 : PUP100K when PMIC_ON_REQ || SOC_NOT_FAIL
2'b10 : always disable PUP100K
2'b11 : PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL -- recommended setting
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.
Also update s_init to skip pfd reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.
Unconditionally build SPI flash compatible SPL images.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.
For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.
This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.
Signed-off-by: Daniel Allred <d-allred@ti.com>
|
|
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
|
|
This patch enables the DFU boot mode support
for dra7x platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
|
|
Move this config to Kconfig option and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove unneeded variables and assignments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
|
|
It should be enough to call low(5us)->high pulse for all cases
to provide proper reset. There is no need to call high->low->high.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Mode pins can be used as output for reset. Xilinx boards are using
this feature as additional way how to reset USB phys and also others
chips on the boards.
Mode1 is used on all these boards for this feature.
Let SPL toggle reset on this pin by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
SPL needs to have bigger stack size because of USB.
Simple malloc needs to be disabled because dfu code requires different
allocation functions. There is no space in OCM that's why random place
in DDR is used.
BOOTD must be disabled because it is causing compilation error.
All variables are disabled and used only variables valid for DFU because
they are simple huge. Including automatic variables added by
CONFIG_ENV_VARS_UBOOT_CONFIG.
Hardcode addresses for u-boot, atf, kernel and dtb
just for SPL DFU code.
Enable SPL DFU for zcu100.
Create new usb_dfu_spl variable just to run Linux kernel loaded in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
There are a few options which use lower case. We should use upper case for
all CONFIG options.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add usbtty/nand hunk to include/configs/spear3xx_evb.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is a workaround to fix SATA CRC error. Once the root cause
is found the ECC disabling will be removed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
As per the top level U-Boot README "Board Initialisation Flow"
section, board_init_f() should return without calling board_init_r()
directly. Clearing BSS and calling board_init_r() will be done in
crt0_64.S.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
According to design specification, the L2 cache operates at the same
frequency as the A72 CPUs in the cluster with a 3-cycle latency, so
increase the L2 Data RAM and Tag RAM latency to 3 cycles, or else,
will run into different call trace issues.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The deep sleep function of LS1 platform, is mapped into PSCI system
suspend function, this patch adds implementation of it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The EPU Finite State Machie (FSM) is used in both the last stage of
system suspend and the earliest stage of system resume.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The v7_flush_dcache_all function will be called by ls102xa platform system
suspend, it is necessary to make it a public call instead of a local one, but
changing the LENTRY to ENTRY isn't enough, because there is another one using
the same name, so this one gets a psci_ prefix.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Debug server feature has been dropped from roadmap.
Signed-off-by: York Sun <york.sun@nxp.com>
|
