| Age | Commit message (Collapse) | Author |
|---|
|
Enable i2c1 in Stratix 10 devkit.
SOCFPGA_STRATIX10 # i2c bus
Bus 0: i2c@ffc02900
SOCFPGA_STRATIX10 # i2c dev 0
Setting bus to 0
SOCFPGA_STRATIX10 # i2c probe
Valid chip addresses: 14 4C 51 68 74
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Merge qspi dts node from Linux.
Commit 0cb140d07fc75fb (arm64: dts: stratix10: Add QSPI support for Stratix10)
Add -u-boot.dtsi files for non Linux dts properties and
update properties for Uboot.
- add u-boot,dm-pre-reloc
- add alias for spi0
- change compatible for flash
- support quad read and quad write
- change maximum frequency to 100MHz
Tested on Stratix 10 SoC devkit.
SOCFPGA_STRATIX10 # sf probe 0:0
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
The stratix10 socdk ships with 4GB of memory. Modify the
device tree to represent this. Note that to access 4GB of
memory in Stratix 10, due to the IO space from 2GB to 4GB,
we use the fact that the DDR controller ignores upper address
bits outside of the configured DRAM's size. This means that
, the 4GB DRAM is mapped to memory every 4GB.
For an 8GB memory, you can either live with the 2GB IO space,
and loose access to that memory from the processor, or use
the same trick:
Loose 2GB of memory:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* last 4GB */
<1 0x00000000 1 0x00000000>;
u-boot,dm-pre-reloc;
};
or to map it all:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* next 6GB */
<2 0x80000000 1 0x80000000>;
u-boot,dm-pre-reloc;
};
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Commit 5dfd5607af2114047bd ("ARM: socfpga: Pull DRAM size from DT") get
memory size from DT. So, we need to update memory size in memory node.
Otherwise, it cause U-boot hang.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Update dtsi and dts files for resets, phy node and other properties.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
From the Linux v4.16-rc4, add the base dtsi and devkit dts files for
the Stratix10 SoCFPGA platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
