| Age | Commit message (Collapse) | Author |
|---|
|
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
|
|
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The boot mode can be forced by key press
or by TAMP register, requested in kernel by syscon-reboot-mode
tamp: tamp@5c00a000 {
compatible = "simple-bus", "syscon", "simple-mfd";
reg = <0x5c00a000 0x400>;
reboot-mode {
compatible = "syscon-reboot-mode";
offset = <0x150>; /* reg20 */
mask = <0xff>;
mode-normal = <0>;
mode-fastboot = <0x1>;
mode-recovery = <0x2>;
mode-stm32cubeprogrammer = <0x3>;
mode-ums_mmc0 = <0x10>;
mode-ums_mmc1 = <0x11>;
mode-ums_mmc2 = <0x12>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Configure clock tree for all the devices.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch rebase the stm32mp1 device tree source from
linux kernel v4.18-rc1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
No more use static frequency HSI = 64MHz for STGEN clock
but HSE (with higher accurency) by default.
Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency
is provided at boot by BootRom and cp15 cntfrq and modified
during clock tree initialization if needed.
When HSI is no more used by any device, this internal
oscillator can be switched off to reduce consumption.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add minimal devicetree for STM32MP157C-ED1 board,
with only the devices to allow boot from SDCARD:
- RCC for clock and reset
- UART4 for console
- I2C and PMIC
- DDR
- SDMMC0 for SDCard
Waiting Kernel upstream for alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
