summaryrefslogtreecommitdiff
path: root/arch/arm/dts/zynqmp-zcu100-revC.dts
AgeCommit message (Collapse)Author
2020-08-20xilinx: Fix xlnx,mio_bank propertyMichal Simek
s/xlnx,mio_bank/xlnx,mio-bank/g DT binding is describing mio-bank not mio_bank that's why fix all DTSes and also driver itself. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-04-06arm64: zynqmp: Update Copyright years to 2020Michal Simek
Trivial change. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source propertySudeep Holla
Most of the legacy "gpio-key,wakeup" boolean property is already replaced with "wakeup-source". However few occurrences of old property has popped up again, probably from the remnants in downstream trees. This patch replaces the legacy properties with the unified "wakeup-source" property introduced by: "Input: gpio_keys - switch to using generic device properties" (sha1: 700a38b27eefc582099fdf69effacfad0ad738a4) Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zcu100-revC: Give wifi some time after power-onJan Kiszka
Somewhere along recent changes to power control of the wl1831, power-on became very unreliable on the Ultra96, failing like this: wl1271_sdio: probe of mmc2:0001:1 failed with error -16 wl1271_sdio: probe of mmc2:0001:2 failed with error -16 After playing with some dt parameters and comparing to other users of this chip, it turned out we need some power-on delay to make things stable again. In contrast to those other users which define 200 ms, Ultra96 is already happy with 10 ms. Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zynqmp: Fix node names which contain "_"Michal Simek
s/_/-/ for node names. It fixes warnings like this: ... Warning (node_name_chars_strict): /cpu_opp_table: Character '_' not recommended in node name ... Issues reported by make dtbs W=12 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Switch zcu100 revC to use firmware clock driverMichal Simek
There is no issue with using firmware based driver instead of fixed clock one. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100Michal Simek
ina226 hwmon driver is deprecated and it is recommended to use new iio based driver. The patch is enabling iio-hwmon driver to export functionality from IIO to hwmon interface to be able to use lm-sensors package. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15xilinx: dts: Remove additional empty linesMichal Simek
Trivial fix. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15arm64: zynqmp: Add reset-on-timeout for all boards and modify default ↵Mounika Grace Akula
timeout value This patch adds reset-on-timeout to FPD WDT which will trigger an interrupt to PMU when watchdog expiry happens and PMU takes the necessary action. If this property is not enabled, reason will not be known when watchdog expiry happens. This patch also modifies the default timeout to 60 seconds. Reason is that if u-boot enables WDT, it will set the timeout to 10 seconds and this is not enough to boot till Linux and start the WDT application in Linux. 60 seconds is the maximum safest value to boot till Linux and start the WDT application. Users need to change this timeout value to fit their needs. Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29arm64: zynqmp: Disable ltc2952 poweroff chipMichal Simek
This chip is on the board but handling should be done via firmware not via Linux driver. Changing status property to keep it in the tree to describe it instead of removing this node completely. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19arm64: xilinx: Setup default number of chipselects for zcu100Michal Simek
There is only one chipselect on each connector. Define it directly in board dts file. There should be an option to use more chipselects via gpios. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15arm: zynq: Drop #address-cells and #size-cells from gpio-keysMichal Simek
dtc is showing some warnings and this change was also done in the Linux kernel as "Input: gpio-keys - clean up device tree binding example" with this fragment in commit message "Drop #address-cells and #size-cells, which are not required by the gpio-keys binding documentation, as button sub-nodes are not devices." Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Remove broken-cd from zcu100-revCMichal Simek
Card detect bit was broken on revA and it is working fine with revC board that's why this property can be removed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Enable cadence WDT for zcu100Michal Simek
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot there is proper reset. Watchdog expires and PMU fw is informed and based on setting proper action is taken. The patch is enabling reset-on-timeout feature and also fixing fixed clock rate for watchdog where 100MHz is max (and also default) clock value. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu100 aka Ultra96 boardMichal Simek
Add support for Xilinx zcu100. Signed-off-by: Michal Simek <michal.simek@xilinx.com>