summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2019-11-10rockchip: rk3399: Add Leez P710 supportAndy Yan
Specification - Rockchip RK3399 - LPDDR4 - TF sd scard slot - eMMC - M.2 B-Key for 4G LTE - AP6256 for WiFi + BT - Gigabit ethernet - HDMI out - 40 pin header - USB 2.0 x 2 - USB 3.0 x 1 - USB 3.0 Type-C x 1 - TYPE-C Power supply Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1: "arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC" (sha1: fc702ed49a8668a17343811ee28214d845bfc5e6) Signed-off-by: Andy Yan <andyshrk@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-08Merge branch '2019-11-07-master-imports'Tom Rini
- Add Phytium Durian Board - Assorted bugfixes - Allow for make ERR_PTR/PTR_ERR architecture specific
2019-11-08armv8: dts: ls1088a: add PSCI binding for LS1088AMathew McBride
This allows the use of PSCI calls to trusted firmware to initiate reset and poweroff events with CONFIG_PSCI_RESET and CONFIG_ARM_PSCI_FW. This is desirable, for example, if the target board has implemented a custom reset or poweroff procedure in EL3. Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-07ARM: dts: logicpd-som-lv-37xx-devkit-u-boot: Remove unused GPIOAdam Ford
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight. This patch removes the all but GPIO4 from the spl device tree to reduce the SPL footprint. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-11-07ARM: dts: logicpd-torpedo-37xx-devkit-u-boot: Remove unused GPIOAdam Ford
The only GPIO bank needed in SPL is GPIO4 and the SPL space is tight. This patch removes the all but GPIO4 from the spl device tree to reduce the SPL footprint. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-11-07arm: dts: k3-j721e-r5-common-proc-board: Hook buck12_reg to vtm supplyKeerthy
Hook buck12_reg to vtm avs supply Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-j721e-r5-common: Add tps65941 node and dependent wkup_i2c0 nodeKeerthy
Add tps65941 node and dependent wkup_i2c0 node needed for AVS class 0 support Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-j721e-r5-common-proc-board: Add VTM nodeKeerthy
Add VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM. Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in suppliesTero Kristo
Link the vdd-supplies for the voltage domains under the VTM node. Also, enable the node under SPL. This will enable the AVS class 0 support on am65x-evm board. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-am654-r5-base-board: add supply rail for MPUTero Kristo
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached to i2c0 bus. Add device node for this so that it can be controlled via a regulator driver. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for splTero Kristo
Enable wkup_i2c0 as this is needed for voltage control. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: dts: k3-am654-r5-base-board: Add VTM nodeKeerthy
Add VTM node for voltage and thermal management. For u-boot, this is needed for supporting AVS class 0, as the efuse values for the OPPs are stored under the VTM. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07arm: add initial support for the Phytium Durian Boardliu hao
This adds platform code and the device tree for the Phytium Durian Board. The initial support comprises the UART and the PCIE. Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
2019-11-05imx: imx8mm-evk: enable ethernetPeng Fan
add phy-reset-gpios to reset phy Add board_phy_config to configure phy Enable DM_ETH Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05arm: dts: imx8mm: drop assigned clocks for clk nodePeng Fan
Drop assigned clocks for clk node, this will break boot on i.MX8MM EVK board. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05imx: add i.MX8MN DDR4 board supportPeng Fan
Support pinctrl/clk/sdhc, include ddr4 timing data. Log: U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800) Normal Boot Trying to boot from BOOTROM image offset 0x8000, pagesize 0x200, ivt offset 0x0 U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800) CPU: Freescale i.MX8MNano rev1.0 at 24 MHz Reset cause: POR Model: NXP i.MX8MNano DDR4 EVK board DRAM: 2 GiB MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05imx: add dtsi for i.MX8MNPeng Fan
Add dtsi for i.MX8MN Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05arm: dts: imx8qm-mek: add u-boot, dm-spl for lpuart0Peng Fan
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL is enabled. Since uclass power domain is also enabled, to make lpuart work properly, need add u-boot,dm-spl for lpuart power domain and its parent. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05arm: dts: imx8qxp-mek: add u-boot, dm-spl for lpuart0Peng Fan
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL is enabled. Since uclass power domain is also enabled, to make lpuart work properly, need add u-boot,dm-spl for lpuart power domain and its parent. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05imx8qm: mek: enable dm-spl for pmPeng Fan
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled, the bind and probe code in board file could be removed. Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-04Merge tag 'u-boot-imx-20191104' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191104 ------------------- - i.MX NAND: nandbcb support for MX6UL / i.MX7 - i.MX8: support for HAB - Convert to DM (opos6ul, mccmon6) - Toradex i.MX6ull colibri - sync DTS with kernel Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
2019-11-03imx: support i.MX8QM ROM 7720 a1 boardOliver Graute
Add i.MX8QM ROM 7720a1 board support Boot log as below: U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Advantech iMX8QM Qseven series Board: ROM-7720-A1 4GB Build: SCFW 65afe5f6 Boot: SD2 DRAM: 4 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1 , eth-1: ethernet@5b050000 Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com>
2019-11-03arm: dts: imx8mm: sync dts from Linux KernelPeng Fan
Sync dts for i.MX8MM from Linux Kernel 5.4.0-rc1 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03board/BuR/brppt2: initial commitHannes Schmelzer
This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-11-03imx8mm: evk: enable bd71837 pmicPeng Fan
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for DRAM and linux suspend voltage requirement. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03opos6uldev: migrate to DM_VIDEOSébastien Szymanski
Migrate to DM_VIDEO, update the device tree and remove code that is no longer necessary. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03imx: update i.MX8MQ device treesPatrick Wildt
This updates the i.MX8MQ device trees and, necessarily, also the i.MX8MQ clock bindings. These are taken verbatim from from the Linux kernel version v5.4-rc2, which three small changes which were already part of the previous device tree: * Keep the PSCI reserved memory range * Keep the alias for ethernet, so that the MAC address can be set * Keep the modified #include for the IOMUXC pins Signed-off-by: Patrick Wildt <patrick@blueri.se> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-11-03ARM: imx: Convert mccmon6 to use DM/DTS in the u-boot properLukasz Majewski
This commit converts mccmon6's u-boot proper (in a single commit to avoid build breaks) to use solely DM/DTS. The DTS description of the mccmon6 has been ported from Linux kernel (v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03imx: Enable RTC (ds1307) support in the U-Boot proper on TPC70 boardLukasz Majewski
The TPC70 is equipped with DS1307 RTC device. Add code to enable support for it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: dts: imx6ull-colibri: pre-reloc for uart pinmux modesIgor Opaniuk
Add u-boot,dm-pre-reloc properties for uart pinmux configuration nodes, which enables UART as early as possible (before relocation). Without this we miss almost the half of output (U-boot version, CPU defails, Reset cause, DRAM details etc.). Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm") Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-11-03ARM: dts: imx6ull-colibri: change hierarchy of DTS filesIgor Opaniuk
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to keep original imx6ull-colibri.dts in sync with Linux. Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi + additionally fix checkpatch warnings. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-11-03arm: dts: Add devicetree support for iMXQXP AI_ML boardManivannan Sadhasivam
Add devicetree support for iMXQXP AI_ML board from Einfochips. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-11-03arm: dts: am335x: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Heiko Schocher <hs@denx.de> Cc: Felix Brack <fb@ltec.ch> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-11-03arm: dts: am437x: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
2019-11-03arm: dts: dra7: sync cpsw/mdio/phy with latest linux - drop phy_idGrygorii Strashko
Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated phy_id property with phy-handle. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-30Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- H6 dts(i) sync (Clément) - H6 PIO (Icenowy) - Fix pll1 clock calculation (Stefan) - H6 dram, half DQ (Jernej) - A64 OLinuXino eMMC (Sunil)
2019-10-25Merge branch '2019-10-24-ti-imports'Tom Rini
- Enable DFU on dra7xx boards - Further Keystone 3 platform improvements
2019-10-25arm: dts: k3-am65: Add R5F ranges in interconnect nodesSuman Anna
Add the address spaces for the R5F cores in MCU domain to the ranges property of the cbass_mcu interconnect node so that the addresses within the R5F nodes can be translated properly by the relevant OF address API. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25arm: dts: k3-j721e: Add ddr nodeLokesh Vutla
Use the 3733MTs DDR configuration that is auto generated from DDR_Regconfig tool. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Kevin Scholz <k-scholz@ti.com>
2019-10-25ram: k3-am654: Do not rely on default values for certain DDR registerJames Doublesin
Added the following registers to the DDR configuration: - ACIOCR0, - ACIOCR3, - V2H_CTL_REG, - DX8SLxDQSCTL. Modified enable_dqs_pd and disable_dqs_pd to only touch the associated bit fields for pullup and pulldown registers (to preserve slew rate and other bits in that same register). Also update the dts files in the same patch to maintain git bisectability. Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25armv7r: dts: am654-base-board: Rename 1600MHz to 1600MTs in dtsi filenameJames Doublesin
The current configuration of DDR on AM654 base board is for 1600MTs but the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi. Since 1600MHz is misleading, rename it to k3-am654-base-board-ddr4-1600MTs.dtsi Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25ARM: dts: dra7: Add usb peripheral nodes in splFaiz Abbas
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-25Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- DWC3 improvements - i.MX7 EHCI bugfix
2019-10-25Merge tag 'u-boot-atmel-2020.01-b' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel features and fixes for 2020.01 cycle This feature set includes Eugen's work on a new tiny flexcom driver and eeprom mac retrieval for the sam9x60-ek board.
2019-10-25Merge tag 'xilinx-for-v2020.01-part2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 part 2 common: - Fix manual relocation for repeatable commands arm: - Also clean up generated dtbos microblaze: - Add support for Manual relocation in crypto framework - Tune and align architecture bootm support zynq: - DT sync ups - Some defconfig updates - Remove empty board_early_init_f() zynqmp: - Clean firmware handing via drivers/firmware/ - DT/defconfig name alignments - DT cleanups with using firmware based clock driver - Some defconfig updates - Add IIO ina226 DT description - Tune zynqmp_psu_init_minimalize.sh script - Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216 versal: - Clean firmware handing via drivers/firmware/ - Add gpio support - Enable DT overlay/USB/CLK/FPGA - DT updates - Tune mini configuration spi: - gqspi - Remove unused headers
2019-10-25arm: dts: sync dts for Allwinner H6Clément Péron
Sync Kernel DTS for Allwinner H6 boards. Drop /omit-if-no-ref/ keyword as it's not supported by U-boot. commit <d45331b00ddb> Linux 5.3-rc4 Signed-off-by: Clément Péron <peron.clem@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)Sunil Mohan Adapa
A64 OLinuXino board from Olimex has three variants with onboard eMMC: A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In addition, there are two variants without eMMC. One without eMMC and one with SPI flash. This suggests the need for separate device tree for the three eMMC variants. The Linux kernel upstream has chosen to create and use a separate device tree for the eMMC variants instead of adding eMMC support existing device tree. These changes to Linux kernel are queued for Linux 5.4. commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)") This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux device-tree and a64-olinuxino_defconfig. Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org> [jagan: updated linux-next commit details] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25configs: sopine-baseboard: Enable SPI-FLASHJagan Teki
SoPine has winbond SPI-FLASH, so enable the same in defconfig and add aliases for spi0 in -u-boot.dtsi Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-24Merge branch '2019-10-24-UFS-support'Tom Rini
- Add Universal Flash Storage (UFS) support
2019-10-24arm64: zynqmp: Add support for e-a2197-00 System ControllerMichal Simek
Add support for System Controller available on e-a2197-00 base board. System is very similar to p-a2197-00 board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-01 11:33:39 +0000