summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2018-01-24ARM: dts: rmobile: Factor out U-Boot extrasMarek Vasut
Pull out u-boot extras into dtsi files to make synchronization of DTS from Linux kernel as easy as a simple copy. All the U-Boot extras are now in *-u-boot.dts* files instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-24ARM: dts: rmobile: Update DTS to match Linux 4.14Marek Vasut
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.14, commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 . This includes both M3 and H3 ULCB and Salvator-X boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-23ARM: dts: Freescale: re-license device tree files under GPLv2+/X11Pankaj Bansal
The current GPL only licensing on the device trees makes it very impractical for other software components licensed under another license. To make it easier to reuse them, re-license the the device trees for Freescale (now NXP) SoCs and boards under GPLv2+/X11 dual license. Same trend is followed in linux. Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: York Sun <york.sun@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-19ARM: dts: omap3-beagle{-xm}: Add support for BeagleBoardDerald D. Woods
This commit adds OMAP3 BeagleBoard devicetree files from Linux v4.15-rc5. This includes standard OMAP34XX board revisions as well as the 'xM' which is OMAP36XX. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-01-19ARM: dts: am574x-idk: Add initial supportLokesh Vutla
Add initial dts support for am574x-idk Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-17Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-16imx: mx7ulp: modify lpi2c seq numberPeng Fan
Modify the lpi2c alias seq number to align with device. Then no need to add 4 to get the device index. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-15Merge git://git.denx.de/u-boot-imxTom Rini
2018-01-15db410c: add reserved-memory node to dtsRob Clark
If lk lights up display and populates simple-framebuffer node, it will also setup a reserved-memory node (needed by simplefb on linux). But it isn't clever enough to cope when the reserved-memory node is not present. Signed-off-by: Rob Clark <robdclark@gmail.com>
2018-01-15db410c: replace reset driver with psciJorge Ramirez-Ortiz
this should be the norm for armv8 platforms. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db410c: update wlan and bt mac addresses from firmwareJorge Ramirez-Ortiz
The firmware that runs before u-boot modifies u-boot's device tree adding the local-mac-address and local-bd-address properties for the compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan". This commit reads that firmware, retrieves the properties and fixups the device tree that is passed to the kernel before booting. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: stop autoboot when vol- pressedJorge Ramirez-Ortiz
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: enable pmic gpios for pm8994Jorge Ramirez-Ortiz
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: add qualcomm dragonboard 820C supportJorge Ramirez-Ortiz
This commit adds support for 96Boards Dragonboard820C. The board is based on APQ8086 Qualcomm Soc, complying with the 96Boards specification. Features - 4x Kyro CPU (64 bit) up to 2.15GHz - USB2.0 - USB3.0 - ISP - Qualcomm Hexagon DSP - SD 3.0 (UHS-I) - UFS 2.0 - Qualcomm Adreno 530 GPU - GPS - BT 4.2 - Wi-Fi 2.4GHz, 5GHz (802.11ac) - PCIe 2.0 - MIPI-CSI, MIPI-DSI - I2S U-Boot boots chained from LK (LK implements the fastboot protocol) in 64-bit mode. For detailed build instructions see readme.txt in the board directory. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15board: ls1012a: LS1012A-2G5RDB board supportBhaskar Upadhaya
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-12ARM: tegra: don't use CONFIG_SPL_TEXT_BASE when no SPLStephen Warren
64-bit Tegra don't use SPL, and soon won't define CONFIG_SPL_TEXT_BASE when building. Fix the binman .dts file so that it doesn't use undefined values. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12imx: mx6ull-14x14-evk: enable DM QSPI driverPeng Fan
To support QSPI DM driver - Add spi0 alias for qspi node. Which is used for bus number 0. - Modify the n25q256a@0 compatible property to "spi-flash". - Modify spi4 (gpio_spi) node to spi5 - Define DM SPI/QSPI related config to enable QSPI Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-12ARM: imx: Introduce dts for i.MX6SX-SDBPeng Fan
Introduce dts from Kernel commit commit 71ee203389f7cb1c("Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi") Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-11Merge git://git.denx.de/u-boot-sunxiTom Rini
2018-01-11Merge git://git.denx.de/u-boot-usbTom Rini
2018-01-10Merge git://git.denx.de/u-boot-marvellTom Rini
2018-01-10BCM283x ALT5 function for JTAG pinsHenry Zhang
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13 carry altenate function, ALT5 for ARM JTAG Signed-off-by: Henry Zhang <henryzhang62@yahoo.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-10ARM: DTS: stm32: add MMC nodes for stm32f746-disco and stm32f769-discoPatrice Chotard
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746 and STM32F769 discovery boards There is a hardware issue on these boards, it misses a pullup on the GPIO line used as card detect to allow correct SD card detection. As workaround, cd-gpios property is not present in DT. So SD card is always considered present in the slot. Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-10ARM: DTS: stm32: add SDIO controller support for stm32f469-discoPatrice Chotard
STM32F469 SoC uses an arm_pl180_mmci SDIO controller. Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10ARM: DTS: stm32: add stm32f469-disco-u-boot dts filePatrice Chotard
_ Add gpio compatible and aliases for stm32f469 _ Add FMC sdram node _ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl, pwrcfg and gpio nodes. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10ARM: DTS: add STM32F469 Discovery board supportPatrice Chotard
This DT file comes from kernel v4.15-rc1 stm32f469-pinctrl.dtsi header has been updated with correct STMicroelectronics Copyright. Remove the paragraph about writing to the Free Software Foundation's mailing address as requested by checkpatch. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10ARM: DTS: stm32: add stm32f429-disco-u-boot dts filePatrice Chotard
_ Add gpio compatible and aliases for stm32f429 _ Add FMC sdram node with associated new bindings value to manage second bank (ie bank 1). _ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl, pwrcfg and gpio nodes. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10ARM: DTS: stm32: add STM32F429 SoC and its Discovery board supportPatrice Chotard
All these files comes from kernel v4.15-rc1. Update some header with correct STMicroelectronics Copyright. Remove the paragraph about writing to the Free Software Foundation's mailing address as requested by checkpatch. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10ARM: mvebu: correct reference for "ethernet1" on DB-88F6820-AMCChris Packham
The DB-88F6820-AMC connects ethernet@34000 and ethernet@70000 which are labeled as eth2 and eth0 in armada-38x.dts. The ethernet@30000 (eth1) is not used on the AMC board. This eliminates the following bootup message Device 'ethernet@70000': seq 0 is in use by 'ethernet@34000' Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-01-10ARM: sunxi: Remove left-over cd-inverted property from pcDuino3Tuomas Tynkkynen
Commit 8620f384098b ("dm: sunxi: Linksprite_pcDuino3: Correct polarity of MMC card detect") claims that the Pcduino3 device tree had an incorrect polarity for the card detect pin and thus changed the polarity flag of the cd-gpios from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW. Actually the DT was correct since according to the mmc binding, a combination of GPIO_ACTIVE_HIGH + cd-inverted results in an active-low polarity. But because the U-Boot driver lacks the code to look at the cd-inverted property (unlike the Linux driver) it interpreted the polarity of active-high. Thus, after that commit the DT is actually wrong from the binding/Linux point of view. To make both Linux and U-Boot interpret the DT in the same way, just drop the left-over cd-inverted property. I've sent a Linux patch to switch all sunxi DTs over to not using the cd-inverted property, so eventually all sunxi boards in U-Boot will be consistent in not using cd-inverted. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-10sunxi: Add support for Libre Computer Board ALL-H3-CC H3 ver.Chen-Yu Tsai
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry Pi B+ form factor single board computer based on the Allwinner H3 SoC. The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes and connectors are in the exact same position as on the Raspberry Pi B+. Raspberry Pi B+ like peripherals supported on this board include: - Power input through micro-USB connector (without USB OTG) - Native 100 Mbps ethernet using the internal PHY, as opposed to USB-based on the RPi - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to being connected through a USB 2.0 hub on the RPi - TV and audio output on a 3.5mm TRRS jack - HDMI output - Micro-SD card slot - Standard RPi B+ GPIO header, with the standard peripherals routed to the same pins. * 5V, 3.3V power, and ground * I2C0 on the H3 is routed to I2C1 pins on the RPi header * I2C1 on the H3 is routed to I2C0 pins on the RPi header * UART1 on the H3 is routed to UART0 pins on the RPi header * SPI0 on the H3 is routed to SPI0 pins on the RPi header, with GPIO pin PA17 replacing the missing Chip Select 1 * I2S1 on the H3 is routed to PCM pins on the RPi header - Additional peripherals from the H3 are available on different pins. These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3 In addition, there are a number of new features: - Console UART header - Consumer IR receiver - Camera interface (not compatible with RPi) - Onboard microphone - eMMC expansion module port - Heatsink mounting holes This patch adds defconfig and dts files for this board. The dts file is the same as the one submitted for inclusion in Linux, with some minor revisions to match the dtsi file and old EMAC bindings in U-boot. Since the OTG controller is wired to a USB host port, and the H3 has proper USB hosts to handle host mode, the MUSB driver is not enabled. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-09armv8: ls1012a: Add USB 2.0 controller phy type for ls1012aqds boardRan Wang
Without this propertiy, U-Boot will pop warning of 'USB phy type not defined' when select CONFIG_HAS_FSL_DR_USB. Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
2018-01-01Merge branch 'master' of git://git.denx.de/u-boot-rockchipTom Rini
2018-01-01ARM: dts: omap3-evm: Add support for TMDSEVM{3530, 3730}Derald D. Woods
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note that this is the first addition of OMAP34XX devicetree files. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-01-01rockchip: dts: rk3399-evb: support boot from sd-cardKever Yang
Enable sdmmc node in SPL and add it to boot order. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [Fixed commit tags:] Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-29arm: imx: add tzic interrupt controller for imx53Patrick Bruenn
Since commit 999a78d5cf00 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110") dtc warns about: arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000 Fix this by adding a node for the tzic interrupt controller. Copied from "<Linux>/arch/arm/boot/dts/imx53.dts" Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-29ARM: imx: cm-fx6: reinstate USB support by syncing the devicetree with LinuxChristopher Spinrath
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for USB, thereby effectively removing USB support because the cm_fx6 devicetree in the U-Boot does *not* enable the USB nodes. Reinstate the USB support by syncing the devicetree with Linux whose devicetree enables the USB nodes properly. More precisely, use the devicetree found in Linux v4.15-rc1 with the following two changes: 1) Remove the audio mux; the required dt-bindings header is not present in the U-Boot. 2) Keep the usdhc3 MMC controller node currently present in the U-Boot's devicetree to retain the ability to boot from MMC. Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-19Merge git://git.denx.de/u-boot-sunxiTom Rini
2017-12-19arm64: dts: sun50i: h5: Order nodes in alphabetic for orangepi-primeJagan Teki
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-12-18Merge tag 'xilinx-for-v2018.01-rc2-v2' of ↵Tom Rini
git://www.denx.de/git/u-boot-microblaze Xilinx changes for v2018.01-rc2-v2 fpga: - Enable loading bitstream via fit image for !xilinx platforms zynq: - Fix SPL SD boot mode zynqmp: - Not not reset in panic - Do not use simple allocator because of fat changes - Various dt chagnes - modeboot variable setup - Fix fpga loading on automotive devices - Fix coverity issues test: - Fix env test for !hush case - Stephen's patch
2017-12-14Merge git://git.denx.de/u-boot-dmTom Rini
2017-12-14arm64: zynqmp: Use only earlycon bootargs instead of full oneMichal Simek
This is the same patch as was done earlier. Please look at Linux patch: "arm64: zynqmp: Use only earlycon bootargs instead of full one" (sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Remove undocumented dma propertiesMichal Simek
Remove overfetch, ratectrl, include-sg and src-issue dma properties. Driver is not using them and they are also not documented in the binding doc. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
2017-12-14arm64: zynqmp: Add generic compatible string for I2C EEPROMJavier Martinez Canillas
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Enable phys for zcu102Michal Simek
Enable USB3.0 and SATA phy for zcu102 boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Add support for generic QSPI bootMichal Simek
This patch is enabling support for SPL QSPI boot. First of all it is necessary to generate atf-spi.ub which is different format than atf-uboot.ub (this can be made as legacy image too) ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'` aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin ./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin atf-uboot.ub ./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR -n "atf-for-qspi" -E -d bl31.bin atf-spi.ub This patch is using this QSPI layout with offsets: 0 boot.bin 512k atf-ub 640k u-boot.bin 1280k u-boot.img Which corresponding by writing these images(read from MMC) mmcinfo sf probe load mmc 0 10000000 boot.bin sf erase 0 +$filesize sf write 10000000 0 $filesize load mmc 0 10000000 atf-spi.ub sf erase 0x80000 +$filesize sf write 10000000 0x80000 $filesize load mmc 0 10000000 u-boot.bin sf erase 0xa0000 +$filesize sf write 10000000 0xa0000 $filesize load mmc 0 10000000 u-boot.img sf erase 0x140000 +$filesize sf write 10000000 0x140000 $filesize For testing u-boot running in EL3 you can break atf-spi.ub like this: sf probe sf erase 0x80000 +4 Then u-boot.img is executed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Add reference to pmu firmware nodeMichal Simek
This reference is needed for pinctrl driver where some signals can be routed directly to platform management unit (PMU). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-13Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2017-12-12binman: tegra: Convert to use binmanSimon Glass
Update tegra to use binman for image creation. This still includes the current Makefile logic, but a later patch will remove this. Three output files are created, all of which combine SPL and U-Boot: u-boot-tegra.bin - standard image u-boot-dtb-tegra.bin - same as u-boot-tegra.bin u-boot-nodtb-target.bin - includes U-Boot without the appended device tree The latter is useful for build systems where the device is appended later, perhaps after being modified. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-12-09ARM: rmobile: Add R8A77995 D3 Draak boardMarek Vasut
Add bits to support yet another board, the R8A77995 D3 Draak. The DT file is from Linux 4.15-rc1 , commit b35334447513c14a4dd55a67c269a743d4a4824b . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>