| Age | Commit message (Collapse) | Author |
|---|
|
Sync device trees with Linux for easier DT life.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
This will be needed for setting up the System Bus pin-mux via the
LD11/LD20 pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
DT-side updates to make pinctrl on sLD3 SoC really available.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Import DTS files and dt-bindings includes from Linux 4.8-rc1.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
With commit ceec08f50b6, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.
Fixes: ceec08f50b6 ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
|
|
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This adds an emac node to the orangepi-2 dts (not yet merged upstream,
but in u-boot we already have emac support); fixes the alphetically
sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some
usb controllers in sun8i-h3-orangepi-plus.dts which are only used
on the plus2e, as upstream has decided to do a separate dts files
for the plus2e.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The sun8i-emac driver follows an old version of the proposed DT
bindings, where the EMAC clock and EPHY control register range is
listed directly, rather than through a syscon phandle.
Add back the syscon register range to avoid an invalid data access.
We should fix the driver once the Linux kernel bindings have been
finalized.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add a proper dts for the iNet D978 rev2 based A33 tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.
Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
The eMMC on sLD3 is assigned with dedicated pins (only multiplexed
with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The K2G EVM from TI has an SD card slot as
well as onboard eMMC for data storage.
Enable support for these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
K2G SoC from TI has two MMC/SD controllers.
Add device tree data for these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Add device tree for SAMA5D2 Xplained board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Bring in required device tree file and bindings from Linux.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Now that clock and reset drivers exist for Tegra186, we can enable the SD
card controller. Now that a BPMP I2C driver exists for Tegra186, we can
communicate with the PMIC to enable power to the SD card. Hook up the DT
content and board code required to make the SD card work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Enable I2C devices in DT and enable building tegra_i2c.c driver.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, commit msg rework, fixed DT node sort order)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update USB 3.0 controller dts node in ls1021a.dtsi.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
|
|
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Tegra186 has 8 I2C controllers including BPMP I2C. This patch adds the
other 7 generic controllers to Tegra186's DT.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, fixed DT node sort order, tweak patch description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The Tegra186 PCIe DT content is almost identical to previous chips, except
that the:
- There are 3 ports instead of 2.
- Some physical addresses have moved.
- PHY programming is handled by firmware, so CCPLEX DTs don't need to
reference any PHY.
- The power domain is explicitly represented in DT. This change is
mandatory for Tegra186 since standard power domain APIs are used, and
should be made to the DT for older SoCs, although we get away without
doing so since U-Boot currently uses custom APIs that hard-code power
domain IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This allows the BPMP I2C device to be instantiated, which makes it
available to other drivers and the user.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This adds the DT content that's needed to allow board DTs to enable use
of BPMP, clocks, resets, GPIOs, eMMC, and SD cards.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.
Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1: 911954859d6dece49c3e4835faea004cfe392506)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
With the recent bug fixes for the sun8i_emac driver all known issues
are resolved, so we can re-enable the driver.
While at it, also enable the emac on the Orange Pi One.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Jagan Teki <jteki@openedev.com>
|
|
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
