summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2019-08-27stm32mp1: board: support of error led on ed1/ev1 boardPatrick Delaunay
Create a function led_error_blink and add node in device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27stm32mp1: board: enable v1v2_hdmi and v3v3_hdmi regulator on dk2 bootPatrick Delaunay
As for Audio codec IC, HDMI IC is not "IO safe". HDMI regulators (v3v3 and v1v2) must be enabled to allow I2C1 bus usage. HDMI IC must be under reset during power up and keep HDMI and AUDIO devices in reset while they are not used in U-Boot to keep them in low power mode (each device can be kept in reset independently keeping their power supplies ON until kernel). Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: add pull-up on serial rx of console connected to STLINKPatrick Delaunay
Avoid U-Boot auto-boot interruption for line break detection on console when the RX line connected to STLINK is floating (-IO error in getc cause by framing error and testc return 1) Same workaround is applied on all the STMicroelectonics board. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: add key support on DK1/DK2Patrick Delaunay
Allow to use PA13 and PA14 to force fastboot mode or STM32CubeProgrammer mode. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: add ldtc pre-reloc proper in SOC filePatrick Delaunay
The pre-relocation probe is needed to reserve video frame buffer in video_reserve() for all the board; LDTC must be tagged prereloc in SOC U-Boot dtsi file. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: Add PSCI node access before relocationPatrick Delaunay
Add node in DT and avoid error to search UCLASS_SYSRESET in board_f.c::print_resetinfo() and lost 1.6s in U-Boot for the trusted boot chain. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: Add iwdg2 support for SPLPatrick Delaunay
This patch adds independent watchdog support for stm32mp157c in SPL. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: DDR config v1.45Patrick Delaunay
Update DDR configuration with the latest update: - Change DQSGE to 1 for DDR3, to cure missing DQS preamble. Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: sync device tree with v5.3-rc2Patrick Delaunay
Synchronize device tree with v5.3-rc2 label and update the associated u-boot dtsi. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stih410-b2260: Sync DT with kernel v5.2Patrice Chotard
Synchronize U-boot DT with kernel v5.2 for stih410-b2260. Update stih410-b2260-u-boot.dtsi accordingly. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-08-26ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin muxAdam Ford
When the pinmux configuration was added, it was accidentally placed into the omap3_pmx_wkup node when it should have been placed into the omap3_pmx_core. This error was accidentally propagated to U-Boot by me when I blindly copied the device tree from Linux. This patch moves the i2c2_pins and i2c3_pins to the correct node which should eliminate i2c bus errors and timeouts due to the fact the bootloader uses the save device tree that no longer properly assigns these pins. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-23rockchip: rk3288: remove fennec board supportKever Yang
Since there is no one using this board, remove it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: dts: rk3328-rock64: fix usb power supplyKever Yang
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct power supply for USB HOST ports. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: rk3328: migrate u-boot node to -u-boot.dtsiKever Yang
Move all the nodes only shown in u-boot to -u-boot.dtsi to make rk3328.dtsi clean. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: dts: rk3328-rock64: enable usb3 xhci controllerKever Yang
Rock64 has a USB3.0 port, enable the controller so that we can use it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-22armv8: dts: ls1088aqds : Add pcf2127 nodeChuanhua Han
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1088ardb: Add slave nodes under the i2c0 controllerChuanhua Han
This patch adds some slave nodes to support the i2c dm on the device side under the i2c0 controller. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1088a: add I2C node supportChuanhua Han
One ls1088a, there are four I2C controllers. So add all I2C node for ls1088a in device tree. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls2088aqds : Add ds3232 nodeChuanhua Han
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls2088ardb: Add slave nodes under the i2c0Chuanhua Han
Add some slave nodes to support the i2c dm on the device side under the i2c0. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: fsl-ls2088a: add i2c node supportchuanhua han
One ls2088a, there are four I2C controllers. So add I2C nodes in dts for ls2088a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028aqds: Add pcf2127 node under i2c1Chuanhua Han
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028aqds: Add pca9547 node under the i2c0 controllerChuanhua Han
Add pca9547 node to support i2c multiplexer under the i2c0 controller in dts for ls1028aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028ardb: Add slave nodes under the i2c0 controllerChuanhua Han
Add some slave nodes to support the i2c dm on the device side under the i2c0. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160aqds : Add pcf2127 nodeChuanhua Han
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for lx2160aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160ardb : Add the "u-boot, dm-pre-reloc" for i2c0Chuanhua Han
Lx2160ardb need to use i2c0 before relocation, so we also need to set u-boot, dm-pre-reloc to initialize node before relocation. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: Add pcf2127 node for lx2160ardbChuanhua Han
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodesChuanhua Han
In lx2160a soc, there are eight i2c controllers, this patch adds i2c nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller depends. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-20arm: dts: Makefile: clean *dtb_HSSuniel Mahesh
TI HS platforms generate *dtb_HS binary blobs and there is no rule for cleanup. Added entry for cleanup in clean-files target. Signed-off-by: Suniel Mahesh <sunil.m@techveda.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-08-19rockchip: rk3399: Add ROC-RK3399-PC supportLevin Du
Add initial support for ROC-RK3399-PC board. Specification - Rockchip RK3399 - LPDDR4 4GiB - eMMC slot - SD card slot - RTL8211E 1Gbps - HDMI Out, DP, MIPI DSI/CSI, EDP - PCIe M.2 - USB 2.0, USB-3.0 - USB C Type Commit details of rk3399-roc-pc.dts sync from Linux v5.2: "arm64: dts: rockchip: add support for ROC-RK3399-PC board" (sha1: 8bb878cf20ae10809c36db96993bfce7026d062b) Signed-off-by: Levin Du <djw@t-chip.com.cn> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-12Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Various improvements to Keymile boards - mostly DT conversation (Pascal & Holger) - Removal of now unsupported Keymile boards (Pascal & Holger) - Small MVEBU PCI fix (Marek) - Turris Omnia defconfig update (Marek) - Misc Allied Telesis defconfig updates (Chris)
2019-08-12Merge tag 'u-boot-amlogic-20190812' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - amlogic: add support for the SEI Robotic SEI510
2019-08-12Merge branch '2019-08-11-ti-imports'Tom Rini
- More DaVinci updates and fixes - PCIe support on am65x - Watchdog converted to DM - Assorted other bugfixes
2019-08-12arm: dts: k3-am65: add support for PCIe and SERDESSekhar Nori
Add needed device-tree nodes to support PCIe 0 and SERDES on AM65x SoC. The nodes are kept disabled by default. Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-08-12board/BuR/brsmarc1: initial commitHannes Schmelzer
This commit adds support for the B&R brsmarc1 SoM. The SoM is based on TI's AM335x SoC. Mainly vxWorks 6.9.4.x is running on the board, doing some PLC stuff on various carrier boards. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-12ARM: dts: Import Amlogic G12A SEI510 DT from Linux 5.3-rc1Neil Armstrong
Import Linux 5.2-rc1 sei510 DT from 5f9e832c1370 ("Linus 5.3-rc1") for the meson-g12a-sei510 board. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-08-12km/uart: port UART interface of KM Kirkwood boards to driver modelPascal Linder
Activate the driver model for the serial interface in the KM Kirkwood Kconfig file. The associated preprocessor definitions could be removed from the header file. However, the clock of 200 MHz needs to be declared in the device tree. Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-11arm: dts: Add devicetree for Hikey960 boardManivannan Sadhasivam
This commit adds devicetree for Hikey960 board. Most of the contents are copied from Linux kernel with some modifications for u-boot. To be more precise, SD card's speed related properties are removed due to a bug in u-boot clock implementation. Hence forcing the SD controller to work in standard speed. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-08-11arm: dts: Import HI3660 devicetree from LinuxManivannan Sadhasivam
This commit imports HI3660 SoC devicetree from Linux Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-08-10Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- R8A77980 V3H support
2019-08-09ARM: renesas: Add R8A77980 V3H Condor board codeMarek Vasut
Add board code for the R8A77980 V3H Condor board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-08-09ARM: dts: renesas: Add R8A77980 V3H DTs and headersMarek Vasut
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-08-09apalis-tk1: support v1.2 hardware revisionMarcel Ziswiler
Support the V1.2 hardware revision with the following pin muxing changes: Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4 are now used as DDC pins. Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are now used as USB power enable signals. Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power enable signals are now used as GPIO3 and GPIO4. Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is loaded on V1.2 and later modules and resp. USB power enable signals activated. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09Merge tag 'u-boot-rockchip-20190809' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Add rk3399 boards Khadas Edge/-V/-Captain - Add fully souce code support for rk3328 including TPL/DRAM init - Enable boot from eMMC for rk3399 rock960/ficus boards - turn on the IO supply for dw_mmc
2019-08-07ARM: dts: add hifsys reset for MediaTek SoCsRyder Lee
This adds missing hifsys reset parts in header files. Tested-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
2019-08-07arm: dts: change MT7629 to use spi-mem rather than qspiWeijie Gao
The original mtk_qspi driver has been removed. We change MT7629 to use newly added mtk-spimem driver. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-08-05rockchip: dts: rk3328: update dmc node for driverKever Yang
Update dmc node for full feature driver. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> [cherry picked from commit https://github.com/rockchip-linux/u-boot/commit/1e1495636574c78ea9d3af3e0aae95d5204612d6 with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05rockchip: dts: rk3328: Add rk3328-evb-u-boot.dtsiMatwey V. Kornilov
Split u-boot specific dts configuration to separate rk3328-evb-u-boot.dtsi Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05arm: dts: ficus: Enable booting from eMMC when using SPLManivannan Sadhasivam
This commits enables booting from eMMC when using SPL on 96Boards Ficus board by adding SDHCI to boot order. Since the SDHCI driver already has the reloc flag, this works straightaway. While we are at it, let's also include the common u-boot dtsi for rk3399. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05arm: dts: rock960: Enable booting from eMMC when using SPLManivannan Sadhasivam
This commits enables booting from eMMC when using SPL on 96Boards Rock960 board by adding SDHCI to boot order. Since the SDHCI driver already has the reloc flag, this works straightaway. While we are at it, let's also include the common u-boot dtsi for rk3399. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2025-01-18 03:05:46 +0000