| Age | Commit message (Collapse) | Author |
|---|
|
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Enable USB Host for Odroid-C2 board
- Add Open-Drain/Open-Source emulation in GPIO uclass
|
|
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
- MediaTek USB host support
|
|
- 2 MVEBU related fixes
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.07
----------------
- imxrt: fix LCD clock, fix doc
- new board: Coral Dev
- imx8: enable Cache in SPL. SNVS, update SCFW API
- imx8MM: fix reset, 8MQ quand and QuadLite, CPU speed grading
- MX6ULL : is_imx6ull to include i.MX6ULZ
- Net: add config to enable TXC delay
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/682033914
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
|
|
This resolves issues with certain SFP modules.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add usb, phy and clock nodes
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
|
|
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
This patch synchronizes the device tree with that from 5.6.7.
This also adds nodes for crypto and ddrc, which makes keeping
the device tree files from individual boards in sync with the
Linux kernel. This is helpful when boads reference those nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
commit b2f5da9dd068 ("rockchip: rk3399: Add Nanopi M4 board support") added
support for Nanopi M4 board with Dual-Channel 4GB LPDDR3-1866 RAM.
This patch adds another variant of NanoPi M4 board with Dual-Channel
2GB DDR3-1866 RAM.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
|
|
Add Firefly ROC-RK3399-PC Mezzanine board which is an
extension board on top of roc-rk3399-pc.
Will drop the separate defconfig file, once we support
the board detection at runtime.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sync Firefly ROC-RK3399-PC Mezzanine Board dts file
from Linux v5.7-rc1.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Sync rk3399 dts(i) files from v5.7-rc1 linux-next.
Reason:
To get updated PCIe nodes and properties on respective
dts(i) files.
Summary:
- sync won't include new board dts(i)
- sync will add required files used on respective dts(i)
- rk3399-puma-u-boot.dtsi spiflash label changed to norflash
- move puma.dtsi bios_enable into rk3399-puma-u-boot.dtsi
- move legacy max-frequency of sdhci into rk3399-u-boot.dtsi
- update cross-ec-[keyboard|sbs].dtsi path as per U-Boot
- keep roc-rk3399-pc dc_12v changes to -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Move U-Boot specific properties into rk3399-evb u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Move U-Boot specific properties into rk3399-puma u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
If the VBUS regulator is always-on, XHCI will fail to detect USB 3.0
devices; USB 2.0 devices will work however.
Make the VBUS regulator controllable and tie it to only the XHCI. This
makes all three USB ports usable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This syncs rk3328 device tree files from the Linux kernel next-20200324.
The last commit to touch these files is:
b2411befed60 ("arm64: dts: add bus to rockchip amba nodenames")
Additional changes not yet in the Linux kernel include:
arm64: dts: rockchip: rk3328: drop #address-cells, #size-cells from grf node
arm64: dts: rockchip: rk3328: drop non-existent gmac2phy pinmux options
arm64: dts: rockchip: rk3328: Replace RK805 PMIC node name with "pmic"
Changes include:
- conversion of raw pin numbers to macros
- removal of deprecated RK_FUNC_* macros
- update of device tree binding headers
- new devices
- device tree cleanups
- gmac2phy disabled in -u-boot.dtsi as it is not supported in U-boot
This includes a re-ordering of the USB device nodes compared to upstream
Linux, moving the dwc2 OTG controller after the EHCI/OHCI nodes. This is
currently required as otherwise the dwc2 controller would not be able to
detect devices in some cases. This may be due to lack of USB PHY support
in U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The "hnp-srp-disable" property for dwc2 is specific to U-boot, not part
of upstream Linux's device tree bindings.
Move it to rk3328-u-boot.dtsi to avoid losing it when syncing device
tree files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The device tree file for rk3328-evb in the Linux kernel does not have
gmac2io enabled. Instead, gmac2phy is enabled, but that is not supported
in U-boot.
Move the gmac2io related nodes to rk3328-evb-u-boot.dtsi to preserve the
current functionality. When the device tree files are synced, gmac2phy
should be marked as "broken" in -u-boot.dtsi files.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
USB 3.0 is only supported in U-boot, not in the Linux kernel where the
device tree files are ultimately synced from. While the xhci node was
moved, the external vbus regulator was not.
Move it as well.
Fixes: 2e91e2025c1b ("rockchip: rk3328: migrate u-boot node to -u-boot.dtsi")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2020.07-rc2
mmc:
- Fix dt property handling via generic function
clk:
- Fix versal watchdog clock setting
nand:
- Fix zynq nand command comparison
xilinx:
- Enable ubifs
- Sync board_late_init configurations with initrd_high setup
- Make custom distro boot more verbose
zynq:
- Kconfig alignments
- Fix nand cse configuration
zynqmp:
- Fix zcu104 low level qspi configuration
- Small DT updates
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
|
|
- rmobile gen2/gen3 DTS sync and defconfig consolidation
|
|
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1046ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1046A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1043ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1043A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the QorIQ DPAA Frame Manager v3 device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add lpuart nodes to enable lpuart feature
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (8 x
VSC8514, AQR105). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (4 x AQR405
and 4 x CS4340). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the EMDIO1 node and describe the 2 AR8035 RGMII PHYs and
the 2 AQR107 PHYs. Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add the External MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Add enable rng node in px30-evb-u-boot.dtsi.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
