summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2020-06-30Merge tag 'mips-pull-2020-06-29' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next - net: pcnet: cleanup and add DM support - Makefile: add rule to build an endian-swapped U-Boot image used by MIPS Malta EL variants - CI: add Qemu tests for MIPS Malta
2020-06-25ARM: dts: imx6q-tbs2910: Fix Ethernet regressionFabio Estevam
Since commit: commit 6333cbb3817ed551cd7d4e92f7359c73ccc567fc Author: Michael Walle <michael@walle.cc> Date: Thu May 7 00:11:58 2020 +0200 phy: atheros: ar8035: remove static clock config We can configure the clock output in the device tree. Disable the hardcoded one in here. This is highly board-specific and should have never been enabled in the PHY driver. If bisecting shows that this commit breaks your board it probably depends on the clock output of your Atheros AR8035 PHY. Please have a look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set "clk-out-frequency = <125000000>" because that value was the hardcoded value until this commit. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com> , the clock output setting for the AR803x driver is removed from being hardcoded in the PHY driver and should be passed via device tree instead. Update the device tree with the "qca,clk-out-frequency" property so that Ethernet can work again. Reported-by: Soeren Moch <smoch@web.de> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Soeren Moch <smoch@web.de>
2020-06-25Merge tag 'xilinx-for-v2020.10' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2020.10 Versal: - xspi bootmode fix - Removing one clock from clk driver - Align u-boot memory setting with OS by default - Map TCM and OCM by default ZynqMP: - Minor DT improvements - Reduce console buffer for mini configurations - Add fix for AMS - Add support for XDP platform Zynq: - Support for AES engine - Enable bigger memory test by default - Extend documentation for SD preparation - Use different freq for Topic miami board mmc: - minor GD pointer removal net: - Support fixed-link cases by zynq gem - Fix phy looking loop in axi enet driver spi: - Cleanup global macros for xilinx spi drivers firmware: - Add support for pmufw reloading fpga: - Improve error status reporting common: - Remove 4kB addition space for FDT allocation
2020-06-24topic: zynqmp: Add support for zynqmp-xilinx-xdp platformMike Looijmans
XDP - Xilinx Drone Platform is a board for drones or other UAV. Pinmux the SD card by default, and if the SD card detect line is high (inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on extension card and shares connection with on board wife. That means that when SD card is present in the board wifi can't be used. There seems to be an issue with DDR access from PL at 2400MT/s, after updating the PMU and ATF firmware this is causing extremely slow DDR access. Reducing the DDR speed from 2400 to 2133 appears to solve that issue, even though the hardware has proven to be 2400 capable. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: zynqmp: Change spi-max-frequency for qspi miniT Karthik Reddy
Change mini u-boot qspi spi-max-frequency to 108Mhz, make the frequency similar to full u-boot qspi flash spi-max-frequency. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: zynqmp: Fix si570 clock output names and referencesSaeed Nowshadi
Align clock output names with node references. Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-23mx6cuboxi: enable MMC and eMMC in DT for SPLWalter Lozano
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23arm: dts: imx: fsl-imx8qm.dtsi: fix gpio aliasesYe Li
Current aliases missed gpio0 node, and this node shoud be aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we will get below message when running "gpio status" command, and see the reason by "dm uclass". => gpio status Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000' Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000' Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000' => dm uclass uclass 36: gpio 0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1) 1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0) 2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1) 3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2) 4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3) 5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4) 6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5) 7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6) Signed-off-by: Ye Li <ye.li@nxp.com>
2020-06-22ARM: dts: imx6qdl-sabresd: Fix AR8031 phy-modeFabio Estevam
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode) the correct phy-mode should be "rgmii-id", so fix it accordingly to fix the Ethernet regression. This problem has been exposed by commit: commit 13114f38e2ccea9386726d8b9831dfc310589548 Author: Vladimir Oltean <vladimir.oltean@nxp.com> Date: Thu May 7 00:11:51 2020 +0200 phy: atheros: Explicitly disable RGMII delays To eliminate any doubts about the out-of-reset value of the PHY, that the driver previously relied on. If bisecting shows that this commit breaks your board you probably have a wrong PHY interface mode. You probably want the PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-22ARM: dts: imx6qdl-sabreauto: Fix AR8031 phy-modeFabio Estevam
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode) the correct phy-mode should be "rgmii-id", so fix it accordingly to fix the Ethernet regression. This problem has been exposed by commit: commit 13114f38e2ccea9386726d8b9831dfc310589548 Author: Vladimir Oltean <vladimir.oltean@nxp.com> Date: Thu May 7 00:11:51 2020 +0200 phy: atheros: Explicitly disable RGMII delays To eliminate any doubts about the out-of-reset value of the PHY, that the driver previously relied on. If bisecting shows that this commit breaks your board you probably have a wrong PHY interface mode. You probably want the PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Fix the phy-mode accordingly to fix the regression. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-22ARM: dts: imx6qdl-sr-som: Sync with kernel 5.8-rc1Fabio Estevam
Sync the device tree with 5.8-rc1. It basically contains the following extra kernel commit: commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09 Author: Russell King <rmk+kernel@armlinux.org.uk> Date: Wed Apr 15 16:44:17 2020 +0100 ARM: dts: imx6-sr-som: add ethernet PHY configuration Add ethernet PHY configuration ahead of removing the quirk that configures the clocking mode for the PHY. The RGMII delay is already set correctly. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> , which passes the 'qca,clk-out-frequency' property and it is important to specify the correct frequency generated by the AR8035. Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Tom Rini <trini@konsulko.com>
2020-06-19Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spi into nextTom Rini
- Convert fsl_espi to driver model (Chuanhua) - Enable am335x baltos to DM_SPI (Jagan) - Drop few powerpc board which doesn't have DM enabled (Jagan)
2020-06-19Merge tag 'u-boot-stm32-20200619' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - fix SD card cart detect on DHCOM and ST boards
2020-06-19ARM: dts: stm32: Reinstate card detect behavior on ST boardsPatrick Delaunay
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far unsupported, reinstate the old cd-gpios behavior until this handling is fully implemented. This avoid potential issue for SDCard boot: the card detect fails with floating gpio. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-06-19ARM: dts: stm32: Reinstate card detect behavior on DHSOMMarek Vasut
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far unsupported, reinstate the old cd-gpios behavior until this handling is fully implemented. This permits the DHSOM to boot from SD again, without this patch the card detect fails. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-06-18ARM: tegra: Enable PSCI support for Tegra210 and Tegra186Jon Hunter
The PSCI nodes are currently not populated for the Tegra210 and Tegra186 devices. This prevents the PSCI driver from being able to identify the PSCI method used by these devices and causes the probe of the PSCI driver to fail. Since commit 81ea00838c68 ("efi_loader: PSCI reset and shutdown") was added, which moves the PSCI EFI system reset handler into the PSCI driver, this has prevented the EFI system reset from working for Tegra210 and Tegra186. Therefore, populating these nodes is necessary to fix the EFI system reset for Tegra210 and Tegra186. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-06-16omap5: uevm: convert to device modelTero Kristo
Convert omap5 uevm board to device model. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap5: Copy device tree from linux 5.7.yTero Kristo
Copy all the device tree files required for omap5 uevm support from mainline Linux. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: sdp: convert to device modelPeter Ujfalusi
Convert omap4 sdp to device model. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: Copy device tree from Linux 5.7.y for SDP4430Peter Ujfalusi
Copy all device tree files required for omap4 sdp4430 support from mainline Linux. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: panda: convert to device modelTero Kristo
Convert omap4 panda to device model. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16omap4: Copy device tree from Linux 5.7.yTero Kristo
Copy all device tree files required for omap4 panda support from mainline Linux. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2020-06-16dts: ARM: stm32mp15: add OP-TEE node in u-boot DTSIEtienne Carriere
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is needed since commit [1] that changed U-Boot/stm32mp15 to detect OP-TEE availability by probing the resource instead of relying on U-Boot configuration. The software sequence implemented by [1] is fine but U-Boot DTS/DTSI files were not updated accordingly since, hence OP-TEE presence is never detected by U-Boot, preventing Linux kernel from using OP-TEE resources. For consistency and to synchronize stm32mp15 DTSI files (excluding U-Boot specific DTSI files) with the Linux kernel ones, this change also moves the OP-TEE reserved memory nodes from board generic DTSI files to U-Boot specific board DTSI files. Link: [1] commit 43df0a159df6 ("stm32mp1: dynamically detect op-tee presence") Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-06-15Merge tag 'mmc-2020-6-15' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- fsl_esdhc sdr104 and hs200 fix and error path fix - fsl_esdhc workaround 3.3v io issue - ca_dw_mmc cleanup - presidio-asic emmc DT update.
2020-06-15board: presidio-asic: update eMMC DT informationAlex Nemirovsky
Change DT compatibility name to match change in driver's name. Remove unused io_ds and fifo_mode fields from DT. Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Peng Fan <peng.fan@nxp.com> CC: Jaehoon Chung <jh80.chung@samsung.com> CC: Tom Rini <trini@konsulko.com>
2020-06-14arm: dts: socfpga: cyclone5: Update i2c-scl-falling-time-nsLey Foon Tan
Commit e71b6f6622d6 ("i2c: designware_i2c: Rewrite timing calculation") change the hcnt and lcnt timing calculation. New timing calculation is based on calculation from Designware i2c databook. After this new timing calculation, hcnt will have negative value with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts. This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall time used in Designware i2c driver) for Uboot. Before the fix: => i2c dev 0 Setting bus to 0 Failure changing bus number (-22) After the fix: => i2c dev 0 Setting bus to 0 => i2c probe Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70 Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2020-06-09Merge tag 'u-boot-imx-20200609' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.07 ----------------- - mx53: mx53menlo Convert to DM_ETH, fix fail boot - imx8mp_evk: fix boot issue - MX6, display5: fix environment - drop warnings (watchdog) for i.MX8mm i.mx8mp - enable bootaux for i.MX8M Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999
2020-06-08ARM: dts: imx: m53menlo: Convert to DM_ETHMarek Vasut
Convert the board to DM_ETH instead of legacy networking. This requires a minor addition to the DT to satisfy the requirement for specifying a PHY node. No functional change from board user perspective. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-08ARM: dts: imxrt1050: indent lcdif node correctlyGiulio Benetti
Accidentally submitted a patch with indentation not correct, let's fix it by indenting wrong lines. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-06-07rockchip: puma: reorganize devicetrees to actually work and match upstreamHeiko Stuebner
So far the puma dts files only just included the main puma dtsi without handling the actual baseboard and rk3399-puma.dtsi was very much detached from the variant in the mainline Linux kernel. Recent changes resulted in a strange situation with nonworking puma boards. Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi") moved the sdram include from rk3399-puma-ddrX.dts to new files rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though. Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") replaced the rk3399-puma.dtsi nearly completely, but in the kernel it definitly depends on a baseboard dts to actually enable peripherals like sd-slot, uarts, etc. So to untagle this and bring the whole thing more in line with mainline Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate DDR-option devicetrees and instead replace them with a puma Kconfig option to select and include the needed DDR variant. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation for -u-boot.dtsiHeiko Stuebner
Tabs not spaces, so transform it to the common styling. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulatorHeiko Stuebner
The regulator enable-gpio uses opposite values for the declaration vs. the enable_active_low property, breaking the regulator enablement. Make the usbhost-supply work again by bringing them in sync again. This mimics the upstream Linux change found on: http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for gmac reset pinHeiko Stuebner
The gmac reset has opposite values for the gpio declaration and the separate reset-active, bring this in line to make u-boot also find the ethernet-phy. This mimics the upstream Linux commit found on https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: add SPI bootMarcin Juszkiewicz
U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) Trying to boot from SPI U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: vidconsole Err: vidconsole Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 => Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Add SPI bootJagan Teki
U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1 NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020 U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3399-evb: add stdout-path for the boardKever Yang
The 'stdout-path' is missing after dts sync. Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3328: add rock-pi-e dts fileb.l.huang
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328 Quad-Core ARM Cortex A53. Net - Dual ethernet port, 1 X Gbe, 1 X 100M USB - USB 3.0 DC - USB-Type C, 5V 2A Storage - TF card, eMMC Just build idbloader.img and u-boot.itb for Rockpi E board and follow the blow steps to replace the relevant partition. dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-04Merge tag 'u-boot-atmel-fixes-2020.07-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel fixes for 2020.07 cycle This set includes just two small commits that fix a build warning and add a missing serial node.
2020-06-01Merge tag 'u-boot-stm32-20200528' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - stm32mp15: fix DT on DHCOR SOM and avenger96 board - stm32mp15: re-enable KS8851 on DHCOM
2020-05-31Merge tag 'u-boot-rockchip-20200531' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fix mmc of path after syncfrom kernel dts; - Add dwc3 host support with DM for rk3399; - Add usb2phy and typec phy for rockchip platform; - Migrate board list doc to rockchip.rst; - Add rk3399 Pinebook Pro board support; - Update dram_init in board_init and add memory node in SPL;
2020-05-31rockchip: Add initial support for the Pinebook Pro laptop from Pine64.Peter Robinson
Specification: - Rockchip RK3399 - 4GB Dual-Channel LPDDR4 - eMMC socket - mSD card slot - 128Mbit (16Mb) SPI Flash - AP6256 for 11AC WiFi + BT5 - 14 inch 1920*1080 eDP MiPi display - Camera - USB 3.0, 2.0 ports - Type-C port with alt-mode display (DP 1.2) and 15W charge - DC 5V/3A - optional PCIe slot for NVMe SSD drive Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-31arm: dts: rockchip: Add initial DT for Pinebook ProPeter Robinson
Sync initial support for Pinebook Pro device tree from Linux 5.7-rc1. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-30ARM: dts: rk3399-evb: usb3.0 host supportFrank Wang
Configure 'tcphy1' and 'usbdrd_dwc3_1' nodes to support USB3.0 host for Rockchip RK3399 Evaluation Board. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29arm64: dts: rk3399-nanopi4: Add u-boot,spl-boot-orderJagan Teki
Add u-boot,spl-boot-order as sdhci and sdmmc for booting from eMMC and SD card. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29rockchip: Fix spl mmc boot device ofpathJagan Teki
Linux v5.7-rc1 dts(i) sync has changed the sdmmc node from dwmmc@fe320000 to mmc@fe320000 and this ofpath is being used in rockchip spl bootdevice code. So, update the ofpath with a new node name and prefix "same-as-spl" to missing u-boot,spl-boot-order. Bug log: U-Boot SPL 2020.07-rc2-00256-g9c5fef5774 (May 24 2020 - 20:20:43 +0530) Trying to boot from MMC2 mmc_load_image_raw_sector: mmc block read error Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices Fixes: 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux" Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-05-29arm: dts: meson-gxl: fix USB gadget by adding missing nodes for U-BootNeil Armstrong
The khadas-vim, khadas-vim2, libretech-ac & libretech-*-pc boards were missing DT tweak to enable USB gadget. Add them to their -u-boot.dtsi files and include the right gxl-u-boot.dtsi. Fixes: a19e8a0f03 ("arm: dts: meson-gxl: Add USB Gadget nodes for U-Boot") Reported-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-05-29arm: dts: khadas-vim3: include meson-g12-common-u-boot.dtsi to enable HDMI ↵Neil Armstrong
output Include the common g12 u-boot tweaks to permit enabling video output tweaks on Khadas VIM3 boards. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-05-28ARM: dts: stm32: Disable SDR104 mode on AV96Marek Vasut
Disable SDR104 mode until we know it is really stable. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-28ARM: dts: stm32: Repair I2C2 operation on AV96Marek Vasut
The I2C2 uses different pinmux on AV96, use correct pinmux and also add comments about the I2C being present on the "low-speed" expansion connector X6. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-05-28ARM: dts: stm32: Add alternate pinmux for I2C2 pinsMarek Vasut
Add another mux option for I2C2 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
generated by cgit (git 2.34.1) at 2025-01-08 13:26:58 +0000