summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2016-03-15Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2016-03-14ARM: dts: k2g: Add support for PMMCNishanth Menon
Enable support for PMMC the TI power processor on K2G. This processor manages all power management related activities on the SoC and and allows the Operating Systems on compute processors such as ARM, DSP to offload the power logic away into the power processor. U-boot just has a load responsibility, hence the view of the hardware from a bootloader perspective is different from the view of hardware from a Operating System perspective. While bootloader just loads up the firmware, Operating Systems look at the resultant system as "hardware". Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14rockchip: dts: Add LVDS supportJacob Chen
Add these node to be used in rockchip LVDS and VOP driver. Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-02-29ARM: uniphier: add eMMC boot supportMasahiro Yamada
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and clock) to the SPL DTB. CONFIG_SUPPORT_EMMC_BOOT is also necessary to use "mmc partconf" command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29ARM: dts: uniphier: add SD/MMC host controller nodesMasahiro Yamada
This host controller is available for all UniPhier SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29ARM: dts: uniphier: add GPIO controller nodesMasahiro Yamada
Make the GPIO driver really active. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29ARM: dts: uniphier: rework System Bus nodesMasahiro Yamada
Follow the changes of DTS in Linux. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-24Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2016-02-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-02-24arm: socfpga: cv_socdk: Add support for QSPI bootMarek Vasut
Add missing DT nodes to allow booting from QSPI NOR. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com> Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24arm: socfpga: av_socdk: Add support for QSPI bootMarek Vasut
Add missing DT nodes to allow booting from QSPI NOR. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com> Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24arm: ls1021aqds: Enable driver model lpuart serial driverYork Sun
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart to driver model suport. Enable lpuart port driver. Signed-off-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-23arm: ls1021aqds: Convert to driver model and enable serial supportYork Sun
Split duart configuration as device tree file. Move /chosen node out of board commone device tree. Convert ls1021aqds nor and SD configurations to driver model support (qspi already uses DM). Enable ns16550 DM serial driver for nor configurations. Signed-off-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-22ARM: zynq: Add reset-gpio property for USB on ZyboMichal Simek
DTS syncup with Linux kernel. Add missing reset-gpio property. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22ARM: zynq: Enable u-boot,dm-pre-reloc for qspiNathan Rossi
Enable u-boot,dm-pre-reloc for qspi for zc706, zed and microzed. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-18ARM: tegra: enable USB device mode port on DalmoreStephen Warren
This allows U-Boot to expose UMS and DFU protocols on this port in device mode, or to act as a USB host on the port, using an "OTG" (micro-B to female A host) cable. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: video: Move LCD driver to use the DM PWM driverSimon Glass
Use the driver-model PWM driver in preference to the old code. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: video: Convert tegra20 LCD driver to driver modelSimon Glass
Move this driver over to use driver model. This involves rearranging the code somewhat. The effect is that everything is run from the probe() method. Boards which use this are fixed up, but only seaboard is tested. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: dts: Sync tegra20.dtsi with Linux v4.4Simon Glass
This file has changed quite a bit since it was set up. Sync it back with Linux v4.4. Adjust the users slightly to cope with the changes: - the host1x node is now called host1x@50000000 - we need a clocks node to provide the clk32k_in phandle - active usb nodes need status = "okay" - active i2c nodes need status = "okay" Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: dts: Sync up nyan-big files with LinuxSimon Glass
Sync up these files with Linux v4.4. Some differences remain, principally that the addresses are still 32-bit in U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: dts: Sync up the tegra124 device tree files with LinuxSimon Glass
Sync up these files with Linux v4.4. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-14ARM: uniphier: add support for PH1-Pro4 Ace and Sanji boardsMasahiro Yamada
Initial commit for PH1-Pro4 Ace and Sanji boards. Note: There are two variants for the Ace board in terms of the amount of DDR memory; 1GB or 2GB. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil boardMasahiro Yamada
This is used for on-board inter-connection. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil boardMasahiro Yamada
This board has an EEPROM connected to the I2C channel 0 of the SoC. Its slave address is 0x54. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add clocks properties to EHCI nodesMasahiro Yamada
This allows the EHCI driver to get clocks from device tree. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add device nodes for MIO control blockMasahiro Yamada
This block provides clock and reset control for MIO (Media I/O) hardware blocks such as USB2.0, SD card, eMMC, etc. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add device nodes for Peripheral control blockMasahiro Yamada
This block provides clock and reset control for peripherals such as UART, I2C, IC card, etc. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add device nodes for System Control blocksMasahiro Yamada
These are mainly used for controlling clocks and resets. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14ARM: dts: uniphier: add reference clock nodesMasahiro Yamada
Add master clock nodes generated by crystal oscillators. PH1-sLD3, PH1-LD4: 24.576 MHz PH1-Pro4, ProXstream2: 25.000 MHz PH1-Pro5: 20.000 MHz Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-08ARM: dts: k2g: Add keystone net dts filesMugunthan V N
Add keystone net DT support for k2g evm. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-06Use correct spelling of "U-Boot"Bin Meng
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-02arm: pcm052: Add device tree file'sBhuvanchandra DV
- Add device tree files for Phytec phyCORE-Vybrid Board. - Enable lpuart support for Phytec phyCORE-Vybrid Board. - Use UART1 for stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vf610-twr: Add device tree file'sBhuvanchandra DV
- Add device tree files for NXP/Freescale VF610 Tower Board. - Enable lpuart support on NXP/Freescale VF610 Tower Board. - Use UART1 as stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: colibri-vf: Enable serial supportBhuvanchandra DV
- Enable lpuart support on Toradex Colibri VF50/VF61 - Use UART0 for stdout. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Update the license stringBhuvanchandra DV
Since SPDX license is already there, drop the full one. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02arm: vybrid: Enable lpuart supportBhuvanchandra DV
Add device tree node's for lpuart on Vybrid platform Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-01armv8/ls1043aqds: fix DSPI/QSPI node in dts fileQianyu Gong
Fix the lost dts info when merging patches. Fix DSPI node for 'commit e0579a5852b3 ("armv8/ls1043aqds: add DSPI support")' and QSPI node for 'commit 166ef1e90ce4 ("armv8/ls1043aqds: add QSPI support in SD boot")'. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-01-27Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-01-27armv8/ls1043aqds: add QSPI support in SD bootGong Qianyu
QSPI and IFC are pin-multiplexed on LS1043A. So we use ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: Add lpuart supportWenbin Song
Add lpuart support using the driver model. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: Spilt off board device treeWenbin Song
Move new /chosen node out of the board device tree. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27ARM64: zynqmp: DT: Fix UART compatible stringSoren Brinkmann
ZynqMP has r1p12 not r1p8. r1p12 contains break detection support. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM64: zynqmp: Correct the watchdog timer interrupt numberPunnaiah Choudary Kalluri
Corrected the watchdog timer interrupt number. Origin value was for CSUPMU watchdog. Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM64: zynqmp: Fix coding style in phy nodeMichal Simek
Trivial fix. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM: zynq: Move spi node to aligned locationMichal Simek
Keep nodes aligned. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM: zynq: Fix all remaining zynq platform to use stdout-pathMichal Simek
Fix console setup for all remaining zynq boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM: zynq: Clean DTSI coding styleMichal Simek
Fix minor indentation problems. Signed-off-by: Michal Simek <monstr@monstr.eu> Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27arm: mvebu: Add support for the Armada XP theadorable boardStefan Roese
This patch adds support for the Armada XP (MV78260) based theadorable board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR, LCD and SATA (SSD) interfaces / devices. Two defconfigs are added: theadorable_defconfig: The production U-Boot version with a stripped down drivers and feature list. This removes networking, USB and PCI support. theadorable_debug_defconfig: The debugging / testing U-Boot version with full support for all drivers. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: Stefan Roese <sr@denx.de>
2016-01-26sunxi: Add suport for A83T based Banana-pi M3 BoardVishnu Patekar
Add dts and defconfig for Banana-pi M3 board. It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI, mic, AP6212 Wifi, etc on it. It is paired with AXP813 PMIC which is almost same as AXP818. Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com> [hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit (git 2.34.1) at 2024-12-27 22:12:50 +0000