summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2020-09-09ARM: dts: stm32: Adjust PLL4 settings on AV96 againMarek Vasut
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the 50 MHz generated from PLL4Q cannot be divided well enough to produce accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz, which is in tolerance for the SDMMC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Gerald Baeza <gerald.baeza@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-09-09ARM: dts: stm32: Pull UART4 RX high on AV96Marek Vasut
There is no dedicated pull resistor on the AV96 UART4 (console UART) pin. In case there is no UART adapter installed on the AV96, the line is floating and can trigger reception of garbage characters, which in turn can abort U-Boot autoboot. Add default pull up to mitigate this problem. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-08-31Merge tag 'ti-v2020.10-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Update to ABI 3.0 - Fix i2c write in eeprom driver
2020-08-31arm: dts: a37x0: enable sd card support on espressobinWilson Ding
Enabled SDIO slot 0 (south bridge) for SD card on Espressobin board. Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3 Signed-off-by: Wilson Ding <dingwei@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/60945 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> [pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO] Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm64: a37xx: pci: Make PCIe Reset GPIO DT compatible with Linux kernel DTPali Rohár
Change active-high to active-low and change DT property name from reset-gpio to reset-gpios. This format of gpio reset is used by pci-aardvark driver in Linux kernel. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm64: dts: armada-3720-espressobin: fix COMPHY nodesMarek Behún
This commit fixes initialization of COMPHY on EspressoBin. Commit 22f418935be4 ("phy: marvell: a3700: Use comphy_mux on Armada 37xx.") introduced usage of comphy_mux on Armada 37xx comphy driver. The lanes are defined in comphy_a3700.c as described in functional specification, that is: lane 0 is SGMII1 or USB3 lane 1 is PCIe or SGMII0 lane 2 is SATA or USB3 But the DTS for EspressoBin configures PCIe on lane 0 and USB3 on lane 1, which is wrong in the sense of the specification and doesn't work with the comphy_mux code, which is 2 years now (the aardvark driver causes synchronous abort in U-Boot). It worked till the above mentioned commit, because the code for powering up PCIe PHY doesn't work with lane number at all, and the code for powering up USB3 PHY works differently only if USB3 is on lane 2, ie. the check goes like: if (lane == 2) something else something else so it does not differentiate between lanes 0 and 1. In the future I shall post patches that remove the comphy_a3700 driver and add comphy driver which uses calls to ATF, like Linux' driver does. This will have the advantage of same DTS bindings as Linux', but till this is done, we need this patch. Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Pali Rohár <pali@kernel.org> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm: dts: k3-am65: Update the RM resource typesLokesh Vutla
Update the ringacc and udma dt nodes to use the latest RM resource types similar to the ones used in k3-j721e dt nodes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-25Merge tag 'u-boot-rockchip-20200820' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fix rk3399 evb sdcard support - Fix for SPL_LED support
2020-08-24arm: dts: mt7623: add USB nodesFrank Wunderlich
This adds USB nodes for MT7623/BPI-R2 Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
2020-08-24arm: dts: mt7622: add USB nodesFrank Wunderlich
Add DTS nodes for MT7622/BPI-R64 Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
2020-08-24arm: dts: rename mt7622-bpi-r64.dtsFrank Wunderlich
rename mt7622-bpi-r64.dts to mt7622-bananapi-bpi-r64.dts to follow naming convensions Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-08-24board: armltd: Add support for Total Compute platformUsama Arif
Total Compute is based on ARM architecture and has the following features enabled in u-boot: - PL011 UART - PL180 MMC - NOR Flash - FIT image with Signature - AVB Signed-off-by: Usama Arif <usama.arif@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-08-21rockchip: dts: rk3399-evb: add sdmmc nodeKever Yang
The sdmmc node is missing after the dts sync patch: 167efc2c7a arm64: dts: rk3399: Sync v5.7-rc1 from Linux But we still need it for boot from SD card, so add it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-08-20Merge tag 'xilinx-for-v2020.10-rc3' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx changes for v2020.10-rc3 - Fix fdtfile variable setup - Fix bootm_*/fdt_high/initrd_high variables handling - Fix Kconfig dependencies for Xilinx drivers - Fix booting u-boot from lowest memory - Fix firmware payload argument count for Versal - Fix dfu configurations - Fix mio_bank property handling - Fix and align code around ID detection - Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG - Simplify logic around reading MAC from eeprom - Decrease malloc length for zynqmp mini qspi - Enable preboot for ZynqMP and Versal i2c: - Fix i2c eeprom partitions handling mmc: - Fix logic around HS mode enabling and use proper functions
2020-08-20xilinx: Fix xlnx,mio_bank propertyMichal Simek
s/xlnx,mio_bank/xlnx,mio-bank/g DT binding is describing mio-bank not mio_bank that's why fix all DTSes and also driver itself. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-08-20i2c: eeprom: Use reg property instead of offset and sizeMichal Simek
Remove adhoc dt binding for fixed-partition definition for i2c eeprom. fixed-partition are using reg property instead of offset/size pair. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-19dts: r64: add sata- and asm_sel nodesFrank Wunderlich
asm_sel is for switching between sata and pcie mode on r64 there is GPIO90 connected to ASM1480 which switches RX/TX pairs to PCIe/SATA connector output-low means sata-controller is active with 2020-10 now reg is also needed for the phy itself Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-08-19arm: dts: mt7622: add PCIe nodes for BananaPi-R64Frank Wunderlich
this patch adds PCIe-Nodes for BananaPi R64 original nodes from Chuanjia Liu for mt7622-rfb Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-08-19dts: r64: add r64 dtsFrank Wunderlich
add a separate DTS for BananaPi R64 because it has 1GB RAM and SATA-Support Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-08-19arm: dts: add watchdog-node for mt7622Frank Wunderlich
adding a watchdog-node to mt7622 dtsi Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-08-19arm: dts: mediatek: add PCIe node for MT7622Chuanjia Liu
This patch adds PCIe node in dts for Mediatek MT7622 Soc. Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Signed-off-by: Henry Yen <henry.yen@mediatek.com>
2020-08-19arm: dts: mediatek: add pciesys support for MT7622 SoCChuanjia Liu
This patch adds pciesys support in dts for MediaTek MT7622 SoC. Signed-off-by: Henry Yen <henry.yen@mediatek.com> Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
2020-08-18ARM: dts: uniphier: resync DT with Linux 5.9-rc1Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-08-13Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Fix dtc warnings for some MVEBU boards
2020-08-13Merge tag 'u-boot-stm32-20200813' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP - Add STM32 FMC2 EBI controller driver - Fix dwc3-sti-glue which allows STiH410-B2260 to boot again - Add fitImage its entry for 587-200 DHCOR SoM - Add both PDK2 and DRC02 DT into DHCOM fitImage its - Fix DHCOM KS8851 ethernet MAC address - Remove stm32mp1 board.c file - Use const for struct node_info in board stm32mp1.c file
2020-08-13arm: mvebu: armada-3720-turris-mox.dts: Fix dtc warningStefan Roese
Fix this dtc warning: Warning (avoid_default_addr_size) Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Behún <marek.behun@nic.cz>
2020-08-13arm: mvebu: armada-388-gp.dts: Fix dtc warningsStefan Roese
Fix these dtc warnings: Warning (reg_format) Warning (avoid_default_addr_size) Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com>
2020-08-13arm: mvebu: armada-xp-maxbcm.dts: Fix dtc warningStefan Roese
Fix this dtc warning: Warning (avoid_default_addr_size) Signed-off-by: Stefan Roese <sr@denx.de>
2020-08-13arm: mvebu: armada-xp-theadorable.dts: Fix dtc warningStefan Roese
Fix this dtc warning: Warning (avoid_default_addr_size) Signed-off-by: Stefan Roese <sr@denx.de>
2020-08-13ARM: dts: stm32: Update eth1addr from EEPROM if eth1 presentMarek Vasut
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851. Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1. The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address of KS8851 was left uninitialized, so fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-08-13ARM: dts: stm32: add FMC2 EBI support for stm32mp157cChristophe Kerello
This patch adds FMC2 External Bus Interface support on stm32mp157c. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-08-11arm: dts: k3-j7200-common-proc-board: Enable CPSW2G portVignesh Raghavendra
Enable CPSW2G port to support networking in U-Boot Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-08-11ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G supportVignesh Raghavendra
Add MCU NAVSS, UDMA and CPSW2G DT nodes. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-08-11ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodesVignesh Raghavendra
J7200 SoM has Cypress HyperFlash connected to HyperBus interface, add DT entries for the same. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-08-11ARM: dts: k3-j7200: Add wkup gpio nodeVignesh Raghavendra
Add wkup_gpio0 node required for detecting whether board mux is set HyperFlash. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-08-11arm: dts: k3-j7200: Add USB related DT entriesVignesh Raghavendra
Add USB related DT entries to enable USB device mode. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-08-11arm: dts: k3-j7200: Add R5 specific dts supportDave Gerlach
Add the basic a72 basic dts for j7200. Following nodes were supported: - UART - MMC SD - I2C - TISCI communication - LPDDR with 1600MTs configuration. Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-08-11arm: dts: k3-j7200: Add dts supportLokesh Vutla
Add the basic a72 dts for j7200. Following nodes were supported: - UART - MMC SD - I2C - TISCI communication Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Vishal Mahaveer <vishalm@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-08-11arm: dts: k3-am654-base-board: Add support for USB0 in SPLFaiz Abbas
Add nodes for USB0 in SPL to enable USB host boot mode Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-08-11arm: dts: k3-am654-r5-base-board: Add USB0 nodesFaiz Abbas
Add USB0 nodes and set them to host mode to support USB host and peripheral boot modes Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-08-11arm: dts: k3-j721e: Fix interconnect node namesSuman Anna
The various CBASS interconnect nodes on K3 J721E SoCs are defined using the node name "interconnect". This is not a valid node name as per the dt-schema. Fix these node names to use the standard name used for SoC interconnects, "bus". Signed-off-by: Suman Anna <s-anna@ti.com>
2020-08-11arm: dts: k3-am65: Fix interconnect node namesSuman Anna
The various CBASS interconnect nodes on K3 AM65x SoCs are defined using the node name "interconnect". This is not a valid node name as per the dt-schema. Fix these node names to use the standard name used for SoC interconnects, "bus". Signed-off-by: Suman Anna <s-anna@ti.com>
2020-08-11ARM: omap3: evm: Complete DM_ETH and DM_USB migrationsDerald D. Woods
This commit completes the migrations for DM_ETH and DM_USB. The board is now consistent with omap3_beagle and other remaining OMAP3 boards. Cc: Tom Rini <trini@konsulko.com> Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2020-08-11arm: dts: k3: Add RTI watchdogsJan Kiszka
Add DT entries for main domain watchdog0 and 1 instances on the J721e well as RTI1-based watchdog on the AM65x. RTI0 does not work for this purpose on the AM65x, so leave it out. On AM65x, we mark the power-domain as shared because RTI firmware such as https://github.com/siemens/k3-rti-wdt may request it as well in order to prevent accidental shutdown of the watchdog. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2020-08-07board: presidio: add LED supportJway Lin
Add LED support for Cortina Access Presidio Engineering Board Signed-off-by: Jway Lin <jway.lin@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> Reviewed-by: Simon Glass <sjg@chromium.org> CC: Simon Glass <sjg@chromium.org>
2020-08-06arm: mvebu: Update CRS305-1G-4S board flash layoutLuka Kovacic
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI partitions. Additionally enable the UBI commands in crs305-1g-4s_defconfig. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jakov Petrina <jakov.petrina@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-06arm: mvebu: Add CRS328-4C-20S-4S boardLuka Kovacic
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated Marvell Prestera 98DX3236 CPU. This commit includes two board variants, namely the factory default one and a Bit variant. The Bit board variant has a bigger Macronix flash. Add basic U-Boot, UART and SPI flash support. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jakov Petrina <jakov.petrina@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-06arm: mvebu: Add CRS326-24G-2S boardLuka Kovacic
MikroTik CRS326-24G-2S board has a switch chip with an integrated Marvell Prestera 98DX3236 CPU. This commit includes two board variants, namely the factory default one and a Bit variant. The Bit board variant has a bigger Macronix flash. Add basic U-Boot, UART and SPI flash support. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jakov Petrina <jakov.petrina@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-06arm: mvebu: Add CRS305-1G-4S Bit boardLuka Kovacic
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated Marvell Prestera 98DX3236 CPU. The Bit board variant is added, which has a bigger Macronix flash. Add basic U-Boot, UART and Winbond SPI flash support. Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jakov Petrina <jakov.petrina@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
2020-08-04Merge tag 'u-boot-imx-20200804' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx For 2020.10 ----------- - fixes for Toradex board - fix warnings from previous PR - HAB: reset instead of panic after failure - new board: MYiR Tech MYS-6ULX - mx6cuboxi: use OF_PLATDATA - further changes for DM Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
generated by cgit (git 2.34.1) at 2024-12-23 17:06:49 +0000