summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2020-01-20arm: dts: k3-am654-r5-base-board: Fix power-domains for wkup_vtm0Lokesh Vutla
wkup_vtm populates only 1 power-domain cell in it's node. But the power-domain cell are defined as 2. Due to this the following warning comes during build: arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/interconnect@42040000/ wkup_vtm@42050000:power-domains: property size (8) too small for cell size 2 Fix this by updating the power-domain cells. Fixes: cfa6bd549c ("arm: dts: k3-am654-r5-base-board: Add VTM node") Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20arm64: dts: k3-j721e-common-proc-board: Fully enable wkup_i2c0 useAndreas Dannenberg
Make the wkup_i2c0 module usable across all stages of U-Boot by adding the needed definitions including the associated pinmux definitions. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20board: ti: beagleboneai: add dts fileJason Kridner
BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers. For more information, refer to: https://beaglebone.ai The corresponding patch against the mainline linux kernel can be found at: https://patchwork.kernel.org/patch/11254903/ This patch introduces the BeagleBone AI device tree. Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver. Signed-off-by: Jason Kridner <jdk@ti.com> Signed-off-by: Caleb Robey <c-robey@ti.com> Cc: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20arm: dts: k3-j721e-common-proc-board: Add pinmux for SD cardFaiz Abbas
Add pinmux for sdhci1 node connected to the SD card. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20arm: dts: k3-j721e-common-proc-board: Remove voltage-ranges from sdhci nodesFaiz Abbas
voltage-ranges properties are NOP. Remove them. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20mmc: am654_sdhci: Get Xin clock by nameFaiz Abbas
Get clk_xin by name instead of by index to avoid having to put clocks in the same order in all devices. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20ARM: dts: da850-lcdk: Update DTS files for SPL device tree supportAdam Ford
Currently, the da850-lcdk uses SPL_OF_PLATDATA and manually loads the necessary source code instead of using the auto-generated, because the drivers don't properly autogenerate the code. This patch simply enables the various device tree options to mimic the da850-evm which doesn't need or use OF_PLATDATA for device tree support. It does not disable OF_PLATDATA. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20arm: dts: k3-j721e: Add DT nodes for USBVignesh Raghavendra
J721e has two instances of Cadence USB3 controller. Add DT nodes for the same. USB0 is configured to device mode and USB1 is configured to host mode. For now only high speed mode is supported. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-17ARM: dts: stm32: Add missing ETHCK clock to ethernet nodeMarek Vasut
Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel' is specified. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-01-17stm32mp1: split board and SOC support for STM32MP15x familyPatrick Delaunay
Split the board and SOC support for STM32MP15x family and prepare the introduction of new boards with STM32MP15x. This path define the 2 configurations: - STM32MP15x: STM32MP15x soc support (new) - TARGET_ST_STM32MP15x: STMicroelectronics board support (choice) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-01-16Merge tag 'xilinx-for-v2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.04 ARM64: - Add INIT_SPL_RELATIVE dependency SPL: - FIT image fix - Enable customization of bl2_plat_get_bl31_params() Pytest: - Add test for octal/hex conversions Microblaze: - Fix manual relocation for one SPI instance Nand: - Convert zynq/zynqmp drivers to DM Xilinx: - Enable boot script location via Kconfig - Support OF_SEPARATE in board FDT selection - Remove low level uart setup it is done later by code - Add support for DEVICE_TREE variable passing for SPL Zynq: - Enable jtag boot mode via distro boot - Removing unused baseaddresses from hardware.h - DT fixups ZynqMP: - Fix emmc boot sequence - Simplify spl logic around bss and board_init_r() - Support psu_post_config_data() calling - Tune mini-nand DTS - Fix psu wiring for a2197 boards - Add runtime MMC device boot order filling in spl - Clear ATF handoff handling with custom bl2_plat_get_bl31_params() - Add support u-boot.its generation - Use single image configuration for all platforms - Enable PANIC_HANG via Kconfig - DT fixups - Firmware fixes - Add support for zcu208 and zcu1285 Versal: - Fix emmc boot sequence - Enable board_late_init() by default
2020-01-16arm: dts: mediatek: move u-boot properties to -u-boot.dtsi fileSam Shih
This patch move u-boot properties to -u-boot.dtsi file. Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
2020-01-16Add support for MT7622 reference boardSam Shih
This adds a general board file based on MT7622 SoCs from MediaTek. This commit is adding the basic boot support for the MT7622 rfb. Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-01-16ARM: MediaTek: Add support for MediaTek MT7622 SoCSam Shih
Add support for MediaTek MT7622 SoC. This include the file that will initialize the SoC after boot and its device tree. Signed-off-by: Sam Shih <sam.shih@mediatek.com> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
2020-01-16ARM: MediaTek: add basic support for MT8512 boardsmingming lee
This adds a general board file based on MT8512 SoCs from MediaTek. Apart from the generic parts (cpu) we add some low level init codes and initialize the early clocks. This commit is adding the basic boot support for the MT8512 eMMC board. Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-16ARM: MediaTek: Add support for MediaTek MT8512 SoCmingming lee
Add support for MediaTek MT8512 SoC. This include the file that will initialize the SoC after boot and its device tree. Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-15Merge tag 'u-boot-imx-20200115' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx ----------------------------------- - imx8: add capricorn giedi deneb boards - imx6: fixed fow wandboard - imx7: DM_ETHER for pico-imx7d - fsl_esdhc_imx: add broken-cd property - New SOC: IMXRT10xx Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/637126531
2020-01-14imx: imxrt1050-evk: Add support for the NXP i.MXRT1050-EVKGiulio Benetti
This commit adds board support for i.MXRT1050-EVK from NXP. This board is an evaluation kit provided by NXP for i.MXRT105x processor family. More information about this board can be found here: https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK The initial supported/tested devices include: - Debug serial - SD Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14ARM: dts: imxrt1050: add dtsi fileGiulio Benetti
Add dtsi file for i.MXRT1050. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14imx: dts: imx8dx: add I2C IPG clock for bus 0 and 2Anatolij Gustschin
IPG clock description is missing for I2C0 and I2C2 busses, add it. Otherwise we see -ENODATA error when trying to get I2C clock for these busses. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2020-01-14ARM: dts: imx6ul-14x14-evk: Pass the "broken-cd" propertyFabio Estevam
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card detect pin on the eSDHC2 port. In such cases the "broken-cd" property must be passed, otherwise the card cannot be detected. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14imx: add imx8x based deneb boardAnatolij Gustschin
Add support for Capricorn Deneb SoM variant. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-14imx: add imx8x capricorn giedi boardAnatolij Gustschin
Add support for i.MX8X based Capricorn Giedi SoM. Supported interfaces: GPIO, ENET, eMMC, I2C, UART. Console output: U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) Trying to boot from MMC1 Load image from MMC/SD 0x3e400 U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07 CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C Model: Siemens Giedi Board: Capricorn Boot: MMC0 DRAM: 1022 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial@5a080000 Out: serial@5a080000 Err: serial@5a080000 Net: eth1: ethernet@5b050000 [PRIME] Autobooting in 1 seconds, press "<Esc><Esc>" to stop Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-14tegra: fdt: Add tegra186-u-boot.dtsiStephen Warren
All Tegra chips except Tegra186 have a tegraNNN-u-boot.dtsi. Duplicate Tegra210's copy of this file for Tegra186. This ensures that a /binman node exists in U-Boot's control DT. Subsequent to 3c10dc95bdd0 ("binman: Add a library to access binman entries") this appears to be required. I haven't really investigated why all this is necessary or how it works, but simply observed the boot failure listed below, bisected it, noticed the inconsistency in DT files, and found that fixing it resolved the boot issue. U-Boot 2020.01-rc4-00256-g3c10dc95bdd0 (Jan 07 2020 - 10:25:00 -0700) SoC: tegra186 Model: NVIDIA P2771-0000-500 Board: NVIDIA P2771-0000 DRAM: 7.8 GiB initcall sequence 00000000fffb7858 failed at call 00000000800955a8 (err=-22) ### ERROR ### Please RESET the board ### Fixes: 3c10dc95bdd0 ("binman: Add a library to access binman entries") Fixes: f2faffecb016 ("binman: tegra: Convert to use binman") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-01-14ARM: dts: zynq: enablement of coresight topologyZumeng Chen
This patch is to build the coresight topology structure of zynq-7000 series according to the docs of coresight and userguide of zynq-7000. Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com> Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Sync gem clock nodes with mainline LinuxMichal Simek
Just fixing indentation and update year in Copyright. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Sync gpio-controller name locationMichal Simek
Sync location with mainline kernel. Added by Linux kernel commit 75926f07baae ("arm64: dts: zynqmp: Add missing gpio-controller to ps gpio"). Fixes: 0b33e0b15600 ("arm64: zynqmp: Add missing gpio property to dtsi") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source propertySudeep Holla
Most of the legacy "gpio-key,wakeup" boolean property is already replaced with "wakeup-source". However few occurrences of old property has popped up again, probably from the remnants in downstream trees. This patch replaces the legacy properties with the unified "wakeup-source" property introduced by: "Input: gpio_keys - switch to using generic device properties" (sha1: 700a38b27eefc582099fdf69effacfad0ad738a4) Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zcu100-revC: Give wifi some time after power-onJan Kiszka
Somewhere along recent changes to power control of the wl1831, power-on became very unreliable on the Ultra96, failing like this: wl1271_sdio: probe of mmc2:0001:1 failed with error -16 wl1271_sdio: probe of mmc2:0001:2 failed with error -16 After playing with some dt parameters and comparing to other users of this chip, it turned out we need some power-on delay to make things stable again. In contrast to those other users which define 200 ms, Ultra96 is already happy with 10 ms. Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: zynqmp: Fix node names which contain "_"Michal Simek
s/_/-/ for node names. It fixes warnings like this: ... Warning (node_name_chars_strict): /cpu_opp_table: Character '_' not recommended in node name ... Issues reported by make dtbs W=12 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: dts: Remove inconsistent use of 'arm,armv8' compatible stringRob Herring
The 'arm,armv8' compatible string is only for software models. It adds little value otherwise and is inconsistently used as a fallback on some platforms. Remove it from those platforms. This fixes warnings generated by the DT schema. Reported-by: Michal Simek <michal.simek@xilinx.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Nishanth Menon <nm@ti.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Chanho Min <chanho.min@lge.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Tero Kristo <t-kristo@ti.com> Acked-by: Wei Xu <xuwei5@hisilicon.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Scott Branden <scott.branden@broadcom.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Chunyan Zhang <zhang.lyra@gmail.com> Acked-by: Robert Richter <rrichter@cavium.com> Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-01-14arm64: zynqmp: Remove incorrect phy from DT for zcu102-revB upMichal Simek
zcu102-revB/up are not removing phy from revA properly because of incorrect name. Fixes: 2975a42b42c5 ("arm64: zynqmp: Use ethernet-phy as node name for ethernet phys") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Add support for zcu1285 revA boardMichal Simek
zcu1285 is the same as zcu1275 but it is using Avnet FMC http://www.ultrazed.org/product/network-fmc-module Unfortunately not everything is connected now that's why this is only describing system which Xilinx is using. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Switch zcu100 revC to use firmware clock driverMichal Simek
There is no issue with using firmware based driver instead of fixed clock one. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14zynqmp: dts: Cleanup no-1-8-v property from sdhci dt nodesT Karthik Reddy
Removed no-1-8-v property from zynqmp sdhci devicetree nodes to allow UHS-I capable SD cards to work in SD3.0 UHS modes. Boards that does not have level shifter for SD, does not support 1.8v. so no-1-8-v property to sdhci dt nodes should be present in zcu102 Rev-A,B, zcu104 Rev-A,C, zcu100, zcu1275 Rev-B boards. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Add support for zcu208Michal Simek
The board is very similar to zcu216 with zu49dr device. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14ARM: zynq: Add missing nand/smcc nodesMichal Simek
Add missing nand/smcc description. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Correct the type of eeprom for zcu216 boardsRaviteja Narayanam
Corrected the type of eeprom in device tree for zcu216 boards according to schematic. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Fix ina226 shunt resistor valueMichal Simek
Fix shunt resistor value for ina226 vccint_ams and vccint_io_bram_ps. 2mOhm shunt was only in early board revision schematics but never got to real revA board. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Remove nand partition description from mini-nandMichal Simek
There shouldn't be a need to use any partition description because it can be used for writing data anywhere. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-08Merge tag 'uniphier-v2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier UniPhier SoC updates for v2020.04 - add pinmux nodes for I2C ch5, ch6 - enable SPI driver and command
2020-01-08Merge tag 'u-boot-imx-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx --------------------------------------------------------------------- Add i.MX8MP SoC and EVK board Update README for i.MX8MN EVK and fix mmc env Add pca9450 driver -------------------------------------------------------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/634211885
2020-01-08Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2020-01-08Merge tag 'u-boot-amlogic-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Khadas VIM3L based on Amlogic S905D3 support - Various fixups for amlogic boards - Unnecessary header includes drop into video/meson
2020-01-09ARM: dts: uniphier: add pinmux nodes for I2C ch5, ch6Masahiro Yamada
The next generation SoC can connect on-board slave devices via I2C ch5 and ch6. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-08imx: add i.MX8MP EVK boardPeng Fan
Add basic i.MX8MP EVK board support U-Boot SPL 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800) power_pca9450b_init DDRINFO: start DRAM init DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Failed to find clock node. Check device tree WDT: Not found! Trying to boot from BOOTROM image offset 0x8000, pagesize 0x200, ivt offset 0x0 U-Boot 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800) CPU: Freescale i.MX8MP rev1.0 at 1000 MHz Reset cause: POR Model: NXP i.MX8MPlus EVK board DRAM: 6 GiB MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 u-boot=> mmc list FSL_SDHC: 1 (SD) FSL_SDHC: 2 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-08arm: dts: freescale: Add i.MX8MP dtsi supportPeng Fan
The i.MX8M Plus Media Applications Processor is part of the growing mScale family targeting the consumer and industrial market. It brings an effective Machine Learning and AI accelerator that enables a new class of applications. It is built in Samsung 14LPP to achieve both high performance and low power consumption and relies on a powerful fully coherent core complex based on a quad core ARM Cortex-A53 cluster and Cortex-M7 low-power coprocessor, audio digital signal processor, machine learning and graphics accelerators. Add the basic dtsi support for i.MX8MP. Patch from Anson Huang for Kernel https://patchwork.kernel.org/patch/11310915/ Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-08arm: dts: add i.MX8MP pinfunc headerPeng Fan
Add i.MX8MP pinfunc header for dts usage Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-07Merge tag 'u-boot-imx-20200107' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx New for 2020.04 --------------- - New boards Embedded Artists COM board Xea Board - Switch to DM: Aristainetos boards Toradex colibri (DM_ETH) iCubox GE bx50v3 mx7dsabre (DM_ETH) cx9020 - New features: Bootaux with elf files Default SYS_THUMB_BUILD for i.MX6/7 - Fixes: DHCOM i.MX6 PDK Engicam i.MX8M tools (imx8m_image) Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/633679664
2020-01-07arm: dts: agilex: Add base dtsi and devkit dtsLey Foon Tan
Add device tree files for Agilex SoC platform. socfpga_agilex-u-boot.dtsi and socfpga_agilex_socdk-u-boot.dts contains Uboot specific DT properties. socfpga_agilex.dtsi and socfpga_agilex_socdk.dts are from Linux (kernel/git/dinguyen/linux.git, commit 6f0bf971bacacc) Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-07 16:54:01 +0000