summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2020-03-30arm: dts: ls1028a: Use flexspi in octal I/O modeKuldeep Singh
Configure RX and TX bus-width values to use flexspi in octal I/O mode. If bus-widths are not specified, then single I/O mode is set by default. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30arm: dts: lx2160a: Use flexspi in octal I/O modeKuldeep Singh
Configure RX and TX bus-width values to use flexspi in octal I/O mode. If bus-widths are not specified, then single I/O mode is set by default. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30arm: dts: lx2160aqds: Add FSPI node propertiesKuldeep Singh
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected on different buses, only one flash can be probed at a time. Add fspi node properties aligned with LX2160A-RDB fspi properties. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30dm: arm64: ls1046a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1046A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-26rv1108: Fix boot regressionOtavio Salvador
Since commit 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") the following boot regression is seen: U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB initcall sequence 67fd12a0 failed at call 6000b927 (err=-22) This happens because the above commit missed to include the "rockchip-u-boot.dtsi" for rv1108, so include this file like it done for other Rockchip SoC dtsi's. Fixes: 79030a486128 ("rockchip: Add Single boot image (with binman, pad_cat)") Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26ARM: dts: Activate pullups in the console pins on rv1108-elgin-r1Otavio Salvador
In order to make the console pins more robust to noise, activate the pullups and increase its drive strength. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-10Merge tag 'mmc-2020-3-9' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- DM support for CAxxxx SoCs - eMMC board for presidio-asic - Add defer probe for mmc sdhci - TI SoCs mmc misc update
2020-03-10arm: dts: imx8mq-evk: add phy-reset-gpios for fec1Alifer Moraes
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the driver reset the phy via dts description adding a reset duration of 10 ms following atheros 8031's datasheet recommendation. Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
2020-03-09ARM: dts: imx8mm-verdin: drop rgmii_rxc_dly/txc_dlyMax Krummenacher
The FEC in the i.MX8MM doesn't support this feature. So don't pretend one can use it. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-03-09ARM: dts: imx8mm-verdin: dm-spl for pinctrl_usdhc1 nodeIgor Opaniuk
Let pinctrl configuration for eMMC node (usdhc1) also be accessible in SPL. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-03-09imx: mx6ul_14x14_evk: configure for 24bpp displayAnatolij Gustschin
Before DM_VIDEO conversion this board used 24bpp display configuration, so use it again. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-09ARM: dts: imx6sx-sdb: Sync with kernel 5.4.16Fabio Estevam
Sync the imx6sx-sdb dts files with kernel 5.4.16. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09ARM: dts: imx6sx: Sync with kernel 5.4.16Fabio Estevam
Sync the imx6sx dts files with kernel 5.4.16. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09arm: dts: k3-j721e-r5-common-proc-board: Use unique names for dummy clocksFaiz Abbas
Update the dummy clock names to use unique identifiers. Otherwise the previous node just gets overwitten by the next one with the same name. This fixes eMMC boot not working on J721e-evm. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-03-09mmc: am654_sdhci: Update output tap delay writesFaiz Abbas
With the latest RIOT, there is a different otap delay value for each speed mode. Add a new binding with every supported speed mode. Also disable a given speed mode in the host caps if its corresponding otap-del-sel is not present. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-03-04Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- ABB SECU board - Assorted minor fixes
2020-03-03ARM: socfpga: Add initial support for the ABB SECU boardHolger Brunck
Add initial support for the ABB SECU board, which is an ArriaV-based SoCFPGA system with ethernet and booting from Denali NAND. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-02-29ARM: dts: uniphier: remove U-Boot own EEPROM compatible and propertyMasahiro Yamada
The compatible string "i2c-eeprom" is U-Boot own compatible, which has never been approved by the DT community. "u-boot,i2c-offset-len" is also a U-Boot own hack. Linux adds "atmel,*" as generic compatibles, and U-Boot also followed it by commit d7e28918aa3f ("i2c_eeprom: Add reading support"). The U-Boot own hack is no longer needed. Just sync with Linux. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-29ARM: dts: uniphier: add reset-names to NAND controller nodeMasahiro Yamada
Import Linux commits: 37f3e0096f71 ("ARM: dts: uniphier: add reset-names to NAND controller node") e98d5023fe1f ("arm64: dts: uniphier: add reset-names to NAND controller node") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-29ARM: dts: uniphier: rename DT nodes to follow json-schemaMasahiro Yamada
Import the nodename changes I made in Linux for avoiding dt-schama warnings. This follows the $nodename patterns in the dt-schema. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-19ARM: dts: rockchip: Sync rk3288-vyasa dts from linuxJagan Teki
Sync rk3288-vyasa dts file from Linux. This sync has changes required to work HDMI output on Vyasa RK3288 board. This sync excludes the io_domains node since it is not available in rk3288.dtsi. Changes like vcc50_hdmi, vdd10_lcd and ddc-i2c-bus are not merged to Linux yet but wil resync later if any further updates on this. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-19rockchip: px30: sync the main px30 dtsi from mainlineHeiko Stuebner
There have been multiple peripherals added to the main px30 dtsi in the Linux kernel since its addition to u-boot. So to make it easier to sync board devicetrees, update the core dtsi from Linux. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-19arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsiPeter Robinson
Move the U-Boot specific bits to a -u-boot.dtsi include so all the u-boot.dtsi hierarchy is included. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-19arm: dts: rockchip: rk3399: Move U-Boot specific bits to rk3399-u-bootPeter Robinson
There's some bits in the U-Boot rk3399.dtsi that aren't yet in the upstream Linux dtsi but are needed for early boot. This moves them to the u-boot.dtsi to make it easier to sync the rest of rk3399.dtsi with upstream. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-19arm: dts: rockchip: Update EVB/Puma devices to upstream USB/dwc3 conventionsPeter Robinson
The upstream linux kernel for the Rockchip 3399 SoC use usbdrd3 naming so move the two remaining devices over to that for their device trees to make it easier to sync with upstream DTs. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-14Merge tag 'u-boot-stm32-20200214' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - add DH Electronics DHCOM SoM and PDK2 board - DT alignment with kernel v5.5-rc7 for stm32mp1 boards - fix STM32 image format for big endian hosts in mkimage - solve warnings in device tree and code for stm32mp1 boards - remove fdt_high and initrd_high for stm32 and stih boards - add support of STM32MP15x Rev.Z - update stm32mp1 readme
2020-02-13ARM: dts: stm32m1: add reg for pll nodesPatrick Delaunay
Fix the following DT dtc warnings for stm32mp1 boards: Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2: node has a unit name, but no reg property Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3: node has a unit name, but no reg property Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: correct ddr nodePatrick Delaunay
This patch fix the warning: dt.dts: Warning (simple_bus_reg): Node /soc/ddr@5A003000 simple-bus unit address format error, expected "5a003000" Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: move FDCAN to PLL4_RAntonio Borneo
LTDC modifies the clock frequency to adapt it to the display. Such frequency change is not detected by the FDCAN driver that instead cache the value at probe and pretend to use it later. Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R. Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: DT alignment with kernel v5.5-rc7Patrick Delaunay
Device tree and binding alignment with kernel v5.5-rc7 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13stm32mp1: pwr: use the last binding for pwrPatrick Delaunay
Update the driver to use the latest binding from kernel v5.5-rc1: no more use syscon or regmap to access to pwr register and only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg" is available. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: DT alignment with kernel v5.4Patrick Delaunay
Device tree and binding alignment with kernel v5.4 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13arm: dts: k3-j721e-r5-common-proc-board: Disable power-domains for mcu uartLokesh Vutla
mcu uart will be used during uart boot for loading sysfw.itb. Since sysfw is not yet available during uart load, power-domain cannot be enabled. We need to rely on ROM for doing that, so disable power-domains and clocks for mcu uart. Also fix the mcu uart frequency. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-13arm: dts: am437x-gp-evm: Add some nodes to u-boot.dtsiFaiz Abbas
Add scm_conf syscon node and its parents as well as the ethernet phy node to u-boot.dtsi. This enables ethernet boot. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-12ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 boardMarek Vasut
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP15xx and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-02-09board: ge: bx50v3: override panelIan Ray
Override the panel compatible string for LCD in U-Boot. Include U-Boot device tree overrides in device-specific device trees so that the panel compatible string is used. Fixes: 8c26739859c6 ("board: ge: bx50v3: sync devicetrees from Linux") Signed-off-by: Ian Ray <ian.ray@ge.com>
2020-02-09board: ge: mx53ppd: enable DM_VIDEOIan Ray
Enable DM_VIDEO for mx53ppd. Enable DM_REGULATOR_FIXED and DM_PWM for the backlight. Remove unused MX53PPD_LCD_POWER. Remove old (incorrect) setup_iomux_lcd. Enable backlight via display enable handler. Use cls command to initiate display in HW agnostic manner. Modify `failbootcmd' to use lcdputs. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: mx53ppd: add i2c eeprom bootcount storageRobert Beckett
Add bootcount node, linking to i2c eeprom "bootcount" partitions for storage. Enable i2c eeprom bootcount backend storage. Enable bootcount command and use it for failbootcmd. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: bx50v3: add i2c eeprom bootcount storageRobert Beckett
Add bootcount node, linking to i2c eeprom "bootcount" partitions for storage. Enable i2c eeprom bootcount backend storage. Enable bootcount command and use it for failbootcmd. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: bx50v3, imx53ppd: use DM I2CRobert Beckett
Remove old (pre-DM) i2c setup code. Enable DM i2c. Convert common code to use DM rtc. Convert common code to read VPD from eeprom partition. Convert the generic i2c PMIC init code to use the new da9063 driver. mx53ppd only: Correct RTC compatible in device tree. Enable MXC DM i2c driver. Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc. Make GPIO banks available during preloc, since initialisation is done in board_early_init_f(). Add gpio_request() calls to satisfy the DM_GPIO compatibility API. Remove unused power configuration. Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Ian Ray <ian.ray@ge.com>
2020-02-09board: ge: bx50v3, imx53ppd: add eeprom partitionsRobert Beckett
Add eeprom partitions to device tree. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09mx7dsabre: Fix usbtog probe when use dfu or umsJoris Offouga
Before: => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 usb dr_mode not found CTRL+C - Operation aborted => dfu 0 mmc 0 usb dr_mode not found After : => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 => dfu 0 mmc 0 Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: dts: imx7s-warp7: Move u-boot specific node in u-boot.dtsiJoris Offouga
These nodes are not in upstream kernel, so move these in u-boot.dtsi Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental ↵Lukasz Majewski
disablement The 'enable-active-high' DTS property configures GPIO so it is active with HIGH state (by default it is low). The 'regulator-boot-on' property indicates that the regulator was enabled in the 'earlier' stage - i.e. bootloader/firmware. In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in very early SPL code, so it shouldn't be modified at latter stages. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-02-09board: toradex: Add Verdin iMX8M Mini supportIgor Opaniuk
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-09arm: dts: imx8mm-pinfunc: sync latest linux-next pin func headerMarcel Ziswiler
Synchronise with latest linux-next kernel pin func header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-07board: presidio-asic: Add basic G3 engr. development board supportAlex Nemirovsky
Add basic Presidio G3 engineering board support Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07arm: dts: mediatek: add ethernet and sgmii dts node for mt7622MarkLee
This patch add eth and sgmii dts node for mt7622 to support ethernet Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
2020-02-06Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Gen 5 and Watchdog fixes
2020-02-05Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for ls1028a, add DM-I2C support, update secure boot header offset
generated by cgit (git 2.34.1) at 2025-01-06 22:13:37 +0000