summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2018-05-28arm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from LinuxJagan Teki
orangepi-pc2 has usb otg routed host with either EHCI0/OHCI0 sync the same from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28arm64: allwinner: h5: orangepi-pc2: Order nodes in alphabeticJagan Teki
Order sun50i-h5-orangepi-pc2.dts nodes in alphabetic Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28ARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from LinuxJagan Teki
Bananapi-m2-plus has usb otg routed host with either EHCI0/OHCI0 sync the same from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28arm64: allwinner: a64: bananapi-m64: Sync usb host nodes from LinuxJagan Teki
Sync bananapi-m64 usb host nodes from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28ARM: dts: sun8i: a83t: Sync usbphy node from LinuxJagan Teki
Sync sun8i-a83t usbphy node details from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28arm64: allwinner: a64: bananapi-m64: Sync usb_otg node from LinuxJagan Teki
Sync bananapi-m64 usb_otg node from Linux. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28sunxi: h3: Sync OTG and HCI nodes from Linux DTJun Nie
Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI or MUSB controller. Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-26ram: stm32_sdram: Adds stm32f429-disco fixes for HardFault at bootingRadoslaw Pietrzyk
- adds reading FMC swap setting from DTB to SDRAM driver - sets FMC swap for stm32f429-disco board - changes ram start address to 0x90000000 Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26db410: added pinctrl node and serial bindingsRamon Fried
Added TLMM pinctrl node for pin muxing & config. Additionally, added a serial node for uart. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-05-26db820c: set clk node to be probed before relocationRamon Fried
The clock and serial nodes are needed before relocation. This patch ensures that the msm-serial driver will probe and provide uart output before relocation. Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-25Revert "sunxi: binman: Add U-Boot binary size check"Maxime Ripard
This reverts commit 819f1e081c527d2d02cdaeec0027384688cf5de0. This check was introduced in order to cope with the size limitation we had when we were still using the raw environment in MMC. However, this introduces padding as well, which can result in an overly huge binary if one wants to flash the environment to some other location. Since we now have a FAT-based environment, this check is not so useful anymore, so we can just drop it. Cc: Andre Przywara <andre.przywara@arm.com> Cc: Måns Rullgård <mans@mansr.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-23ARM: dts: uniphier: sync with Linux 4.17-rc6Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: change phy-mode to 'internal' for LD11Kunihiko Hayashi
Change the phy-mode property to 'internal' that means to use a built-in PHY implemented on LD11 SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add clock-names and reset-names to ethernet nodeKunihiko Hayashi
Add clock-names and reset-names because this node recognizes multiple clocks and resets. ("ether", and so on, for each) Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add required clocks and resets to Pro4 ethernet nodeKunihiko Hayashi
The GIO clock/reset, another MAC clock, and the PHY clock are required for the ethernet of Pro4 SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add syscon-phy-mode property to each ethernet nodeKunihiko Hayashi
Add syscon-phy-mode property specifying a phandle of system controller to each ethernet node. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2018-05-20ARM: rmobile: Update V2H BlancheMarek Vasut
The V2H Blanche port was broken since some time. This patch updates the V2H Blanche port to use modern frameworks, DM, DT probing, SPL for the preloading and puts it on par with the M2 Porter board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-18Fixup various SPDX tags from the latest mergeTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-18Merge git://git.denx.de/u-boot-imxTom Rini
2018-05-18arm: dts: socfpga: stratix10: update dtsi and dtsLey Foon Tan
Update dtsi and dts files for resets, phy node and other properties. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18ARM: socfpga: Synchronize Arria10 SoCDK SDMMC handoffMarek Vasut
Regenerate Altera Arria 10 SoCDK SDMMC handoff file using latest Quartus to get the new set of clock bindings in. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Synchronize Arria10 DTsMarek Vasut
Synchronize Altera Arria 10 DT sources with Linux 4.16.3 as of commit ef8216d28a5920022cddcb694d2d75bd1f0035ca Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Sort the DT MakefileMarek Vasut
Sort the Makefile entries, no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Convert to DM serialMarek Vasut
Pull the serial port configuration from DT and use DM serial instead of having the serial configuration in two places, DT and board config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18arm: imx53: Add support for imx53 boards from K+PLukasz Majewski
This commit adds support for DDC and HSC boards from K+P in u-boot. Console output: U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: WDOG Model: K+P iMX53 DRAM: 512 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial Module EEPROM: ID: TQMa53-CB.0401 SN: 63152762 MAC: 00:0b:64:03:14:2a BBoard:40x0 Rev:10 Net: eth0: ethernet@63fec000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-18i.MX6DL: mamoj: Add PFUZE100 supportJagan Teki
MX6DL Mamoj boards has Freescale PFUZE100 PMIC, add support for it through DM_PMIC dt definition. pmic log: Reviewed-by: Stefano Babic <sbabic@denx.de> ======== => pmic list | Name | Parent name | Parent uclass @ seq | pfuze100@08 | i2c@021f8000 | i2c @ 3 => pmic dev pfuze100@08 dev: 0 @ pfuze100@08 => pmic dump Dump pmic: pfuze100@08 registers 0x00: 10 00 00 21 00 01 3f 01 00 7f 00 00 00 00 00 81 0x10: 00 00 3f 00 00 00 00 00 00 00 00 10 00 00 00 00 0x20: 2b 2b 2b 08 c4 00 00 00 00 00 00 00 00 00 2b 2b 0x30: 2b 08 c4 00 00 72 72 72 08 d4 00 00 2c 2c 2c 08 0x40: e4 00 00 2c 2c 2c 08 e4 00 00 6f 6f 6f 08 f4 00 0x50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x60: 00 00 00 00 00 00 48 00 00 00 10 06 1e 1e 17 10 0x70: 1a 1f 00 00 00 00 00 00 00 00 00 00 00 00 00 Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
2018-05-18i.MX6DL: mamoj: Add I2C supportJagan Teki
i.MX6DL Mamoj has i2c3 and i2c4 buses, add support through DM_I2C with dt definition. i2c log: Reviewed-by: Stefano Babic <sbabic@denx.de> ======= => i2c bus Bus 2: i2c@021a8000 Bus 3: i2c@021f8000 => i2c dev 2 Setting bus to 2 => i2c speed 400000 Setting bus speed to 400000 Hz => i2c probe Valid chip addresses: 20 51 53 => i2c md 53 0xff 00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ => i2c md 51 0xff 00ff: a8 08 40 50 09 43 46 52 42 18 80 8e ae a9 d0 53 ..@P.CFRB......S => i2c dev 3 Setting bus to 3 => i2c speed 100000 Setting bus speed to 100000 Hz => i2c probe Valid chip addresses: 08 40 48 4B => i2c md 08 0xff 00ff: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
2018-05-18i.MX6: board: Add BTicino i.MX6DL Mamoj initial supportJagan Teki
Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-18ARM: i.MX6: dts: Build dtb based on SOC typeJagan Teki
Build dtb's based on SOC type instead building arch type. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-18ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-splJagan Teki
u-boot,dm-spl property is specific to U-Boot, so move it into *u-boot.dtsi files for relevant i.MX6UL files. This make syncing Linux dts files straight forward. Also update the MAINTAINERS file for dts files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-18ARM: dts: imx6ul-isiot: Move usdhc2 into dtsiJagan Teki
Move usdhc2 node along with pinctrl to imx6ul-isiot.dts from imx6ul-isiot-emmc.dts Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-18ARM: dts: i.MX6QDL: U-Boot specific dts for u-boot, dm-splJagan Teki
u-boot,dm-spl property is specific to U-Boot, so move it into *u-boot.dtsi files for relevant i.MX6QDL files. This make syncing Linux dts files straight forward. Also update the MAINTAINERS file for dts files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-17ARM: kirkwood: Add device-tree for sheevaplugChris Packham
Import the dts files from Linux 4.17 and enable device tree control in u-boot. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for pogo_e02Chris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for openrdChris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for nas220Chris Packham
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for iconnectChris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for ib62x0Chris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for guruplugChris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for goflexhomeChris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for dockstarChris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: kirkwood: Add device-tree for dns325Chris Packham
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17ARM: add devicetree files for kirkwood SoCChris Packham
These files are taken verbatim from the Linux kernel 4.17 Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17dts: pinctrl: Provide IMX_PAD_SION definition for imx53 pinctrlLukasz Majewski
The SION pin must be set for proper operation of I2C when DM is enabled. When legacy I2C is used, this bit is set implicitly in the u-boot code: arch/arm/include/asm/arch-mx5/iomux-mx53.h:92: MX53_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x368, 0x040, 4 | IOMUX_CONFIG_SION, 0x820, 0, NO_PAD_CTRL), The Linux kernel uses similar approach with: arch/arm/boot/dts/imx53-tqma53.dtsi:182: MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 After applying this patch it is possible to have the I2C working with DM on imx53 devices: MX53_PAD_KEY_ROW3__I2C2_SDA (0x1ee | IMX_PAD_SION) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-17dts: imx53: Add gpio and i2c nodes to imx53.dtsi fileLukasz Majewski
Those DTS nodes has been ported from Linux kernel (v4.16) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-16ARM: dts: stm32: Update qspi bindings for stm32f746Patrice Chotard
Align qspi bindings following kernel dt-bindings Documentation/devicetree/bindings/mtd/stm32-quadspi.txt from kernel v4.17-rc1. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16ARM: dts: stm32: Add quadspi reset for stm32f746Patrice Chotard
Add missing reset property in quadspi node. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16ARM: dts: exynos5: add the interrupt-parent propertyJaehoon Chung
Add the interrupt-parent property as gic. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit (git 2.34.1) at 2025-01-02 16:52:46 +0000