| Age | Commit message (Collapse) | Author |
|---|
|
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
|
|
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
|
|
BOOT_CFG1[7:4] the NAND boot mode selection is done
only when BOOT_CFG1[7] is 1 hence update the NAND
boot mode detection bit case. This information available
on Table 8-11. NAND Boot eFUSE Descriptions, from IMX6DQRM.
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
|
|
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Before commit 81c4eccb55cc ("imx: mx6: fix USB bmode to use
reserved value") a non-reserved value has been used to trigger
Serial Downloader using bmode, which translated to a GPR9 value
of 0x10. However, on some boards the non-reserved value lead to
unreliable bmode command. With the above mentioned commit, U-boot
switched to use [7:4] b0001, which translates to GPR9 0x10 for
Serial Downloader mode. Check for the new value and classify it
as Serial Downloader mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.
Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
|
|
Commit 54e4fcfa3c749a78 ("ARM: mx6: add MMC2 boot device detection
support in SPL") prevents UDOO neo board to boot:
Trying to boot from MMC2
port 1
MMC Device 1 not found
spl: could not find mmc device. error: -19
SPL: failed to boot from all boot devices
This reverts commit 54e4fcfa3c749a789192e83740a53234182f4ca3.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
|
|
Check BOOT_CFG2[3:4] to determine which SD/MMC port is selected to boot
from. If MMC2 is selected return BOOT_DEVICE_MMC2. In all other cases
return BOOT_DEVICE_MMC1, as we do not have corresponding macro for MMC3
and MMC4.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
|
|
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
|
|
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
|
|
The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.
SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.
The result is that the selected boot device is not used across all
the boot stages.
Update spl_boot_device() to look at gpr9 when necessary.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
Rename some defines containing FAT in their name to be filesystem generic:
MMCSD_MODE_FAT => MMCSD_MODE_FS
CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
|
|
Add a common spl.c file to support boot device functions needed for SPL
such as detecting the boot device.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
|
