| Age | Commit message (Collapse) | Author |
|---|
|
Before commit 81c4eccb55cc ("imx: mx6: fix USB bmode to use
reserved value") a non-reserved value has been used to trigger
Serial Downloader using bmode, which translated to a GPR9 value
of 0x10. However, on some boards the non-reserved value lead to
unreliable bmode command. With the above mentioned commit, U-boot
switched to use [7:4] b0001, which translates to GPR9 0x10 for
Serial Downloader mode. Check for the new value and classify it
as Serial Downloader mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.
Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.
Cc: sbabic@denx.de
v2-Changes:
- No usage of MKIMAGEOUTPUT_$(@F) macro.
- Predefine default value /dev/null in every involved Makefile.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
|
|
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
|
|
These files are blowing up the SPL and should not be required
there as the SPL delivers no command console. Because building fails
for mx27 and mx31 machines with SPL build, we remove the linker flag
for them from the Makefile. Nothing is built for them to be linked
in that directory.
Cc: sbabic@denx.de
v2 Changes:
- Remove mx27 and mx31 from Makefile during SPL build as nothing is built for
them in that directory. And removing the commands with the libs-y directive
lead to linker failures. e.g. "armv5te-ld.bfd: cannot find arch/arm/imx-common/built-in.o: No such file or directory)"
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
|
|
If L2 cache configured as OCRAM, reset it.
Switch to use runtime check.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add iomux settings for i.MX6 SLL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX6 SLL GPT timer support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX6SLL cpu type.
MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Commit 54e4fcfa3c749a78 ("ARM: mx6: add MMC2 boot device detection
support in SPL") prevents UDOO neo board to boot:
Trying to boot from MMC2
port 1
MMC Device 1 not found
spl: could not find mmc device. error: -19
SPL: failed to boot from all boot devices
This reverts commit 54e4fcfa3c749a789192e83740a53234182f4ca3.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
|
|
The ipu has two display interfaces. Make the used one a parameter
in struct display_info_t instead of using unconditionally DI0.
DI0 is the default setting.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
|
|
Check BOOT_CFG2[3:4] to determine which SD/MMC port is selected to boot
from. If MMC2 is selected return BOOT_DEVICE_MMC2. In all other cases
return BOOT_DEVICE_MMC1, as we do not have corresponding macro for MMC3
and MMC4.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
|
|
If CONFIG_USE_IMXIMG_PLUGIN is selected, plugin.bin will be
generated under board/$(BOARDDIR)/.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Introduce USE_IMXIMG_PLUGIN Kconfig
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This commit "2bb014820c49a63902103bac710bc86b5772e843"
do some clean up to use the code in lib/time.c.
But usec2ticks is still being used by security related job ring code.
Bring back the function to avoid build break when CONFIG_FSL_CAAM
is defined.
The computation logic has been changed, using 64-bit variable
to ease the process, making it work on older (MX5) platforms.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
|
|
So the option can easily be selected through menuconfig.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
|
|
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.
Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
|
|
Since the mx6ull adds the AIPS3, so enable its initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The i.MX6ULL's GPT supportting taking OSC as clock source.
Add i.MX6ULL support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX6ULL major cpu type.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
The CPU detection macro is_mx6dq returns 0 on an i.MX6DQP, so we need to
check for it explicitly in order to correctly initialize the pads when
CONFIG_MX6QDL is defined.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
|
|
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Fix a number of typos, including:
* "compatble" -> "compatible"
* "eanbeld" -> "enabled"
* "envrionment" -> "environment"
* "FTD" -> "FDT" (for "flattened device tree")
* "ommitted" -> "omitted"
* "overriden" -> "overridden"
* "partiton" -> "partition"
* "propogate" -> "propagate"
* "resourse" -> "resource"
* "rest in piece" -> "rest in peace"
* "suport" -> "support"
* "varible" -> "variable"
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
|
|
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
|
|
To i.MX6DQPlus, osc can be choosed as the source of gpt, so
add i.MX6DQPlus support in gpt_has_clk_source_osc.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The i.MX6DQPlus support sata interface, we should not
return failure when CPU is i.MX6DQPlus.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Support i.MX6DQPlus, otherwise wrong hab address will be used
for i.MX6QDPlus.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
|
|
Add i.MX6SOLO support for hab function.
The difference between i.MX6SOLO and i.MX6DL is
the number of CPU cores. Besides this, they work
the same.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
According to the product website, the full names are i.MX 7Solo
and i.MX 7Dual, whereas the short form is i.MX7S and i.MX7D. Be
consistent and print the short form for both supported i.MX 7 SoCs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
According PL310 TRM, Auxiliary Control Register
"
The register must be written to using a secure access, and it can be
read using either a secure or a NS access. If you write to this register
with a NS access, it results in a write response with a DECERR response,
and the register is not updated. Writing to this register with the L2
cache enabled, that is, bit[0] of L2 Control Register set to 1,
results in a SLVERR.
"
So If L2 cache is already enabled by ROM, chaning value of ACR
will cause SLVERR and uboot hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
We need to be passing -T firmware here and aren't.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The echo -ne "\xNN" does not work in certain bourne-compatible shells, like
dash. The recommended way of hex->char conversion is using printf(1), but
there is a pitfall here. The GNU printf does support "\xNN" format, but
according to the opengroup documentation, this is not part of POSIX. The
POSIX printf only defines "\NNN" where N is octal. Thus, for the sake of
compatibility, we use that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Read the number of cores in the fuses to distinguish between
the dual and solo versions.
Tested on a mx7d sabresd and on a mx7solo warp7.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
To boot a auxiliary core in asymmetric multicore system, introduce the
new command "bootaux" to do it. Example of boot auxliary core from
0x70000000 where stores the boot head information that should be
parsed by auxiliary core, "bootaux 0x70000000".
Introduce Kconfig option IMX_BOOTAUX.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce Resource Domain Controller support for i.MX.
Now i.MX6SX and i.MX7D supports this feature to assign masters
and peripherals to different domains.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
|
|
Compile misc.c for mx7, since we need related function for
lcdif and nand.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add mx7 secure boot support, add helper macro IS_HAB_ENABLED_BIT
to get the corresponding bit mask per SoC (mx7 or mx6) to identify
if securue boot feature is enabled/disabled.
On authenticate_image only check for mmu enabled on mx6 SoC to
force pu_irom_mmu_enabled so ROM code can perform mmu cache flush
mx7 SoC ROM code does not have this issue as ROM enables cache support
based on fuse settings.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
Use read_fuse api fuction call to read secure boot fuse
settings (enabled/disabled).
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
Rework secure boot support for imx6, move existing hab support
for imx6 into imx-common for SoC reuse.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
We can reuse common functions in lib/time.c, but not reimplement
functions in imx-common/time.c.
Only keep timer_init ,get_tbclk and implement timer_read_counter in
imx-common/time.c.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
|
|
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
Fix coding style.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
boot_mode_apply should be applied only with CONFIG_CMD_BMODE enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Some i.MXes use __NA_ or 0 to avoid setting mux_mode, but the following patch
only take i.MX6/7 into consideration.
"c3c8a5748897b24f18618047804317167a531dd3 imx-common: fix iomux settings"
Use is_soc_type(MXC_CPU_MX7) to avoid breaking other i.MXes when
setting mux_mode.
In this patch, switch to use "asm/imx-common/sys_proto.h" to avoid
build break for "is_soc_type" for vf610 and mx25.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
|
|
When setting iomux for a pin mux, there is no need to check mux_ctrl_ofs.
Also If still checking mux_ctrl_ofs, we have no chance to set iomux
for i.MX7D IOMUXC_LPSR_SW_MUX_CTL_PAD_GPIO1_IO00, because the mux_ctrl_ofs
for this register is 0.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
|
