summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-am33xx/hardware_am43xx.h
AgeCommit message (Collapse)Author
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-12arm: am33xx: Add support for mulitiple PLL input frequenciesLokesh Vutla
am335x supports various sysclk frequencies which can be determined using sysboot pins. PLLs should be configures based on this sysclk frequency. Add PLL configurations for all supported frequencies. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-17ARM: am43xx: Enable QUAD read and EDMA support for ti_qspiVignesh R
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this increases read performance to 4 MB/s. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-04-14board: ti: AM43xx: added USB initializtion codeKishon Vijay Abraham I
Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in am43xx board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14ARM: AM43xx: Enable clocks for USB OTGSS and USB PHYKishon Vijay Abraham I
Enabled clocks for dwc3 controller and USB PHY present in AM43xx. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-01-13arm: am437x: Enable hardware leveling for EMIFJames Doublesin
Switch to using hardware leveling for certain parameters on the EMIF rather than using precalculated values. Doing this also means we have a common place now between am437x and am335x for setting emif_sdram_ref_ctrl with a value for the correct delay length. Tested-by: Felipe Balbi <balbi@ti.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09usb: phy: omap_usb_phy: implement usb_phy_power() for AM437xFelipe Balbi
Newer AM437x silicon requires us to explicitly power up the USB2 PHY. By implementing usb_phy_power() we can achieve that. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-07am43xx: Tune the system to avoid DSS underflowsCooper Jr., Franklin
* This is done by limiting the ARM's bandwidth and setting DSS priority in the EMIF controller to ensure underflows do not occur.
2013-12-18ARM: AM43xx: EPOS_EVM: Add support for LPDDR2Lokesh Vutla
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A) Adding LPDDR2 init sequence and register details for the same. Below is the brief description of LPDDR2 init sequence: -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register -> Wait till initialization is complete and the configure MR registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: clocks: Update DPLL detailsLokesh Vutla
Updating the Multiplier and Dividers value for all DPLLs. Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value returned the MPU DPLL is locked. At different OPPs follwoing are the MPU locked frequencies. OPP50 300MHz OPP100 600MHz OPP120 720MHz OPPTB 800MHz OPPNT 1000MHz According to the latest DM following is the OPP table dependencies: VDD_CORE VDD_MPU OPP50 OPP50 OPP50 OPP100 OPP100 OPP50 OPP100 OPP100 OPP100 OPP120 So at different OPPs of MPU it is safest to lock CORE at OPP_NOM. Following are the DPLL locking frequencies at OPP NOM: Core locks at 1000MHz Per locks at 960MHz LPDDR2 locks at 266MHz DDR3 locks at 400MHz Touching AM33xx files also to get DPLL values specific to board but no functionality difference. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Update the base addresses of modulesLokesh Vutla
PRCM, timer base addresses and offsets are different from AM33xx. Updating the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-12arm: am437: Fix offset for USB registersDan Murphy
Fix the offset for the USB clock registers Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20usb: am437x: Add support for am437x xhci USB hostDan Murphy
Add the support for the am437x xhci usb host. The xHCI host on AM437 is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-15Add TI816X supportTENART Antoine
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com> [trini: Fix warnings about vtp things in emif4.c, adapt AM43XX] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15ARM: AM43xx: Add header filesLokesh Vutla
Adding the following data: -> Prcm structure -> Base addresses -> Pin mux structure. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>