summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-am33xx
AgeCommit message (Collapse)Author
2013-03-24am33xx: add ti814x specific register definitionsMatt Porter
Support the ti814x specific register definitions within arch-am33xx. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24am33xx: refactor am33xx mux support and add ti814x supportMatt Porter
AM33XX and TI814X have a similar mux though the pinmux register layout and address space differ. Add a separate ti814x mux include to support the TI814X-specific differences. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-24am33xx: refactor am33xx clocks and add ti814x supportMatt Porter
Split clock.c for am335x and ti814x and add ti814x specific clock support. Signed-off-by: Matt Porter <mporter@ti.com>
2013-03-24am33xx: refactor emif4/ddr to support multiple EMIF instancesMatt Porter
The AM33xx emif4/ddr support closely matches what is need to support TI814x except that TI814x has two EMIF instances. Refactor all the emif4 helper calls and the config_ddr() init function to use an additional instance number argument. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24am33xx: convert defines from am33xx-specific to generic namesMatt Porter
Eliminate AM33xx specific names to prepare for TI814x support within AM33xx-land. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24am33xx: Add required includes to some omap/am33xx codeTom Rini
- In arch/arm/cpu/armv7/omap-common/timer.c, drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files that the driver needs but had been relying on <config.h> to bring in. - In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h> - In am335x_evm.h and pcm051.h don't globally include <asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h> as that is the only include which defines things the config uses. Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24am335x: Enable DDR PHY dynamic power down bit for DDR3 boardsVaibhav Hiremath
Enable DDR PHY dynamic power down bit, which enables powering down the IO receiver when not performing read. This also helps in reducing overall power consumption in low power states (suspend/standby). Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-22Allow AM335x MPU core clock speed to be specified in the board config fileMark Jackson
Allow AM335x MPU core clock speed to be specified in the board config file. To use, add the following to the board's config file:- #define CONFIG_SYS_MPUCLK <desired clock freq in MHz> Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-11Allow AM33xx boards to setup GPMC chipselects.Mark Jackson
Expose the enable_gpmc_cs_config() function so AM33xx based boards can register GPMC chip selects. Changes in V4: - Fix checkpatch errors (TAB -> space mangling) Changes in V3: - Fix line wrapping Changes in V2: - Indicate this is for AM33xx (not OMAP2) Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-03-08omap: consolidate common mmc definitionsNikita Kiryanov
The various mmc_host_def.h files are almost identical. Reduce code duplication by moving the similar definitions to a common header file. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-02-18am33xx: support for booting via usbethIlya Yanok
This patch adds BOOT_DEVICE define for USB booting and fixes spl_board_init function to call arch_misc_init (this is the place there musb is initialized). Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2013-02-07Add DDR3 support for AM335x-EVM (Version 1.5A)Jeff Lance
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the DDR3 chip. [Hebbar Gururaja <gururaja.hebbar@ti.com>] - Resolve merge conflict while rebasing. File structure is changed in the mainline. So re-arrange the code accordingly. - Update commit message to reflect the DDR3 part number Signed-off-by: Jeff Lance <j-lance1@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
2013-02-07pcm051: Add support for Phytec phyCORE-AM335xLars Poeschel
The board is named pcm051 and has this hardware: SOC: TI AM3359 DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB ETH 1: LAN8710AI SPI-Flash: W25Q64BVSSIG RTC: RV-4162-C7 I2C-EEPROM: CAT32WC32 NAND: MT29F4G08_VFPGA63 PMIC: TPS65910A3 LCD Supported: UART 1 MMC/SD ETH 1 USB I2C SPI Not yet supported: NAND RTC LCD Signed-off-by: Lars Poeschel <poeschel@lemonage.de> [trini: Add #define CONFIG_PHY_ADDR 0 to config] Signed-off-by: Tom Rini <trini@ti.com>
2013-02-07am33xx: add a pulldown macro to pinmux configLars Poeschel
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-01-08Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
This required manual merging drivers/mtd/nand/Makefile and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2012-12-10am33xx: add ELM supportMansoor Ahamed
AM33XX has Error Location Module (ELM) that can be used in conjuction with GPMC controller to implement BCH codes fully in hardware. This code is mostly taken from arago tree. Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am33xx: NAND supportIlya Yanok
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the existing omap_gpmc driver. This patch adds adds required definitions/intialization. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20am33xx: init OTG hardware and new musb gadget driverIlya Yanok
AM33xx has support for dual port MUSB OTG controller. This patch adds initialization for the controller using new MUSB gadget driver and ether gadget. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-10-25am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbersPeter Korsgaard
So other parts can be added. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: support board specific ddr settingsPeter Korsgaard
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard
So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: Add SPI SPL as an optionTom Rini
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am335x: Enable RTC 32K OSC clockVaibhav Hiremath
In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01am33xx: Fix fetching of mmc1 bootmode from bootrom for AM33XXJoel A Fernandes
U-boot should not ignore getting the bootmode passed on from the bootrom. With this, U-boot SPL knows it was loaded from MMC1 and use this info to read full U-boot from MMC1 as well. Cc: pprakash@ti.com Cc: trini@ti.com Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01OMAP: networking support for SPLIlya Yanok
This patch adds support for networking in SPL. Some devices are capable of loading SPL via network so it makes sense to load the main U-Boot binary via network too. This patch tries to use existing network code as much as possible. Unfortunately, it depends on environment which in turn depends on other code so SPL size is increased significantly. No effort was done to decouple network code and environment so far. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>Tom Rini
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx evm: Update secure_emif_sdram_config during ddr initSatyanarayana, Sandhya
This patch updates secure_emif_sdram_config with the same value written to sdram_config during ddr3 initialization. During suspend/resume, this value is copied into sdram_config. With this, a write to sdram_config at the end of resume sequence which triggers an init sequence can be avoided. Without this register write in place, the DDR_RESET line goes low for a few cycles during resume which is a violation of the JEDEC spec. Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
2012-09-01omap4/5/am33xx: Make lowlevel_init available to all armv7 platformsTom Rini
Make the lowlevel_init function that these platforms have which just sets up the stack and calls a C function available to all armv7 platforms. As part of this we change some of the macros that are used to be more clear. Previously (except for am335x evm) we had been setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we should have been doing this initially and do now. Cc: Sricharan R <r.sricharan@ti.com> Tested-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Correct MMC1, remove MMC2 supportTom Rini
- Correct the MMC1 base offset - Remove MMC2 (that area is reserved and not MMC2). - Add the real BOOT_DEVICE_MMC2 value Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Rework pinmux functionsTom Rini
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h> - Make some defines a little less generic now. - Pinmux must be done by done by SPL now. - Create 3 pinmux functions, uart0, i2c0 and board. - Add pinmux specific to Starter Kit EVM for MMC now. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Add support for TI AM335x StarterKit EVMTom Rini
- Board requires gpio0 #7 to be set to power DDR3. - Board uses DDR3, add a way to determine which DDR type to call config_ddr with. - Both of the above require filling in the header structure early, move it into the data section. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and supportTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Correct and clean up ddr_regs structTom Rini
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry. Correct this by documenting a missing register that will be used at some point in the future (when write leveling is supported). Further, the cmdNcs{force,delay} fields are undocumented and we have been setting them to zero, remove. Next, setting of the 'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the ddr_data entries, so program it there. Finally, comment on how we are configuring the DATA1 registers that correspond to the DATA0 (dt0) registers defined in the struct. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Do not touch 'ratio1' fieldsTom Rini
The various ratio1 fields are not documented in any of the documentation I can find. Removing these and testing has yielded success, so remove the code that sets them and move their locations into the reserved fields. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Rework config_io_ctrl slightlyTom Rini
This function sets a number of related registers to the same value (the registers in question all have the same field descriptions and are related in operation). Rather than defining a struct and setting the value repeatedly, just pass in the value. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Use emif_regs struct for storing initialization valuesTom Rini
Rather than defining our own structs to note what to use when programming the EMIF and related re-use the emif_regs struct. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Turn a number of 'int' functions to 'void'Tom Rini
A number of memory initalization functions were int and always returned 0. Further it's not feasible to be doing error checking here, so simply turn them into void functions. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Document what we're doing with ddrctrl->ddrckectrlTom Rini
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros. - Comment what we're really setting in ddrctrl->ddrckectrl which is that we're operating in the normal mode where EMIF/PHY clock is controlled by the PHY. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am335x: ddr_defs: Update EMIF parametersVaibhav Bedia
EMIF parameters are calculated based on the AC timing parameters from the SDRAM datasheet and the DDR frequency. Current values for these paramters in AM335x U-Boot code, though reliable, are not fully optimal. The most optimal settings can be derived based on the guidelines published at [1]. A pre-computed set of values with the most optimum settings for AM335x EVM and BeagleBone can be found at [2]. [1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips [2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Clean up unused DDR defines, prefix more with 'DDR2'Tom Rini
- Remove a handful of unused defines. - Prefix more values with 'DDR2' as DDR3 will require different values. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Move the call to ddr_pll_config, make it take the frequencyTom Rini
Depending on if we have DDR2 or DDR3 on the board we will need to call ddr_pll_config with a different value. This call can be delayed slightly to the point where we know which type of memory we have. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Pass to config_ddr the type of memory that is connectedTom Rini
We need to pass in the type of memory that is connected to the board. The only reliable way to do this is to know what type of board we are running on (which later will be knowable in s_init()). For now, pass in the value of DDR2. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Make config_cmd_ctrl / config_ddr_data take const structsTom Rini
Rework the EMIF4/DDR code slightly to setup the structs that config_cmd_ctrl and config_ddr_data take to be setup at compile time and mark them as const. This lets us simplify the calling path slightly as well as making it easier to deal with DDR3. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Convert to using <asm/emif.h> to describe the EMIFTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Remove DMM_BASE defineTom Rini
The am33xx does not have a DMM, so don't define the base. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: pin mux defintions for CPSW switchChandan Nath
This patch adds pin mux settings for CPSW switch found on TI AM335X based boards (MII and RGMII modes). Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split pinmux into separate patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01am33xx: CPSW init and definitionsChandan Nath
This patch adds platform-specific initialization for CPSW switch on TI AM33XX SoCs. Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split init out of original patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01omap: am33xx: enable gpio supportSteve Sakoman
This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-07-07omap: am33xx: accomodate input clocks other than 24 MhzSteve Sakoman
The PLL setup values currently assume a 24 Mhz input clock. This patch uses V_OSCK from the board config file to support boards with different input clock rates. Signed-off-by: Steve Sakoman <steve@sakoman.com>
generated by cgit (git 2.34.1) at 2024-12-29 03:30:05 +0000