| Age | Commit message (Collapse) | Author |
|---|
|
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
There are 8 SCFG_SPARECR registers in SCFG memory block, not one.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
|
|
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
|
|
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
