summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-mx5
AgeCommit message (Collapse)Author
2012-11-19mx5: Align SPI CS naming with i.MX53 reference manualFabio Estevam
Align SPI chip select naming with i.MX53 reference manual. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-10imx-common: cpu: add imx_ddr_sizeTroy Kisky
Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololiteTroy Kisky
Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate. Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260. I don't have a sololite to verify. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-10-17mx5: lowlevel_init.S: Fix PLL settings for mx53Fabio Estevam
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz. Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz instead. Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI at 1080p because the IPU clock cannot reach the requested frequency. Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its maximum frequency. Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little bit to allow easier comparison with the original clock setup from FSL U-boot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15mx5/6 clocks: Fix SDHC clocksBenoît Thébaudeau
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although they have dedicated clock paths. Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15mx5 clocks: Fix get_lp_apm()Benoît Thébaudeau
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024. In that case: - on i.MX51, this clock comes from the output of the FPM, - on i.MX53, this clock comes from the output of PLL4. This patch fixes the code accordingly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: Add and use CCSR definitionsBenoît Thébaudeau
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx51: Fix USB PHY clocksBenoît Thébaudeau
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks have different clock gate control bit-fields. The existing code was correct only for i.MX53, so this patch fixes the i.MX51 use case. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Jana Rapava <fermata7@gmail.com> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il>
2012-10-15mx5: Fix clock gate valuesBenoît Thébaudeau
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one of these bits like what was done is wrong and can lead to unpredictable behavior depending on the original value of these bit-fields. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5: Use explicit clock gate namesBenoît Thébaudeau
Use clock gate definitions having names showing clearly the gated clock instead of names giving only a register field index. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5 clocks: CleanupBenoît Thébaudeau
Clean up the i.MX5 clock driver: - Use readl() and writel() instead of their __raw_ counterparts. - Use the clr/setbits_le32() family of macros rather than expanding code. - Use accessor macros for bit-fields instead of _MASK and _OFFSET. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx5/6: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15imx: Use MXC_I2C_CLK in imx i2c driverMatthias Weisser
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using MXC_I2C_CLK on all imx systems using i2c. Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-23mx51evk: Add CONFIG_REVISION_TAGBenoît Thébaudeau
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information. If this data is not present, the kernel misconfigures the TZIC, which results in the timer interrupt handler never being called, so the kernel deadlocks while calibrating its delay. Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com> Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-09-01mxc: Define architecture identifierBenoît Thébaudeau
Define ARCH_MXC for i.MX devices. This is useful to identify features or behaviors common to all i.MX SoCs. The i.MX28 is omitted because its architecture is a bit different (like imx/mxc vs. mxs in Linux). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com>
2012-09-01mx5: add iomux-mx51.h includeMatt Sealey
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for the i.MX51. The content of the file is taken from Linux kernel at commit 5d23b39 plus the required changes to make it work in U-Boot. The contained pad settings are the minimum required to make an Efika MX boot and get all the currently-implemented peripherals working in U-Boot. It is recommended that this file not be just a dumping ground for pins but only contain the settings required for all the boards using it. Changes for v2: * reference commit id from Linux kernel * additionally roll in the USB pads * removed GPIO_NUMBER define Signed-off-by: Matt Sealey <matt@genesi-usa.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mx5: Undeclare imx_decode_pll()Benoît Thébaudeau
The imx_decode_pll() function does not exist for mx5, so remove its declaration. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-09-01MX: Set a common gpio.h for all i.MXStefano Babic
Each i.MX has its own gpio.h, defining the same structure. The internal GPIO controller has the same layout (at least for the register used by u-boot) and can be shared. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Matt Sealey <matt@genesi-usa.com>
2012-09-01imx-common/cmd_bmode.c: add imx bmode (bootmode) commandTroy Kisky
This is useful for forcing the ROM's usb downloader to activate upon a watchdog reset. Or, you can boot from either SD Card. Currently, support added for MX53 and MX6Q Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Note: MX53 support untested. Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31imx-common: add i2c.c for bus recovery supportTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31i.mx53: add definition for I2C3_BASE_ADDRTroy Kisky
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-10mx6: Allow mx6 to access the IPUv3 registersFabio Estevam
Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-25mx53: Allow IPUv3 driver to also work on mx53Fabio Estevam
Adjust the IPU base registers so that ipuv3 driver can work on both mx51 and mx53 SoCs. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchangedStefano Babic
After an update to the MX51 reference manual (Rev. 5), the values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH are now clearly wrong: "Bit 13: High / Low Output Voltage Range. This bit selects the output voltage mode for SD2_CMD. 0 High output voltage mode 1 Low output voltage mode" The values are currently negated in code - fixed. Reported-by: David Jander <david.jander@protonic.nl> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: David Jander <david.jander@protonic.nl> Acked-by: David Jander <david.jander@protonic.nl> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15mx53loco: Add CONFIG_REVISION_TAGFabio Estevam
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information. The kernel uses this data to distinguish between Dialog versus mc34708 based boards, and also to distinguish between revA and revB of the mc34708 based boards. Suggested-by: Yu Li <yk@magniel.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15mx53loco: Allow to print CPU information at a later stageFabio Estevam
Print CPU information within board_late_init(). This is in preparation for adding 1GHz support, which requires programming a PMIC via I2C. As I2C is only available after relocation, print the CPU information later at board_late_init(), so that the CPU frequency can be printed correctly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15mx5: Add clock config interfaceFabio Estevam
mx5: Add clock config interface Add clock config interface support, so that we can configure CPU or DDR clock in the later init Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15imx-common: Factor out get_ahb_clk()Fabio Estevam
get_ahb_clk() is a common function between mx5 and mx6. Place it into imx-common directory. Cc: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX53: add function to set SATA clock to internalStefano Babic
The MX53 SATA interface can use an internal clock (USB PHY1) instead of an external clock. This is an undocumented feature, but used on most Freescale's evaluation boards, such as MX53-loco. As stated by Freescale's support: Fuses (but not pins) may be used to configure SATA clocks. Particularly the i.MX53 Fuse_Map contains the next information about configuring SATA clocks : SATA_ALT_REF_CLK[1:0] (offset 0x180C) '00' - 100MHz (External) '01' - 50MHz (External) '10' - 120MHz, internal (USB PHY) '11' - Reserved Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX5: Add definitions for SATA controllerStefano Babic
Add base address and MXC_SATA_CLK to return the clock used for the SATA controller. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15Define UART4 and UART5 base addressesStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16imx: Remove unneeded/repititive definitions from imx headersVikram Narayanan
Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-27mxc_spi: move machine specifics into CPU headersEric Nelson
Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU Introduce two new macros to control conditional setup MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x) MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x) Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
2011-12-11USB: MX5: add helper functions to enable USB clocksWolfgang Grandegger
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com> V2: Fix spacing in crm_regs.h
2011-12-06MX: serial_mxc: cleanup removing nasty #ifdefStefano Babic
The serial driver for iMX SOCs is continuosly changed if a new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port> defines were used only to find the base address for the selected UART. Instead of that, move the base address to the board configuration file and drop all #ifdef from driver. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marek.vasut@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Helmut Raiger <helmut.raiger@hale.at> CC: John Rigby <jcrigby@gmail.com> CC: Matthias Weisser <weisserm@arcor.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2011-10-27imx: fix coding styleFabio Estevam
Fix checkpatch warning and errors in several i.MX related files. While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c regarding the usage of extern in a C file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30MX5: Modify the PLL decoding algorithmMarek Vasut
The PLL decoding algorithm didn't take into account many configuration bits. Adjust it according to Linux kernel. Also, add PLL4 for MX53. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Hui <jason.hui@linaro.org> Tested-by: Jason Liu <Jason.hui@linaro.org>
2011-09-30FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.hMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-04MX5: make use of GPIO framework for MX5 processorStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-09-04ARM: MX51: PLL errata workaroundDavid Jander
This is a port of the official PLL errata workaround from Freescale to mainline u-boot. The PLL's in the i.MX51 processor can go out of lock due to a metastable condition in an analog flip-flop when used at high frequencies. This workaround implements an undocumented feature in the PLL (dither mode), which causes the effect of this failure to be much lower (in terms of frequency deviation), avoiding system failure, or at least decreasing the likelihood of system failure. Signed-off-by: David Jander <david@protonic.nl>
2011-07-14MX5: Update to autogenerated asm-offsets.hStefano Babic
On i.MX5, the asm-offsets.h file is not yet generated as it should be. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Matthias Weisser <weisserm@arcor.de>
2011-07-04MX5: Introduce a function for setting the chip select sizeFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-04MX5: Add iomux structureFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-04MX5: Make the weim structure completeFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-02-02SPI: mxc_spi: replace fixed offsets with structuresStefano Babic
This patch cleans driver code replacing all accesses to registers with fixed offsets with a corresponding structure. Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02MX5: Add initial support for MX53 processorLiu Hui-R64343
Add initial support for Freescale MX53 processor, - Add the iomux support and the pin definition, - Add the regs definition, clean up some unused def from mx51, - Add the low level init support, make use the freq input of setup_pll macro Signed-off-by: Jason Liu <r64343@freescale.com>
2010-11-21imx: Get fec mac address from fuseLiu Hui-R64343
The patch is to support getting FEC MAC address from fuse bank. Signed-off-by: Jason Liu <r64343@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de>
2010-10-28mx51evk: support new relocation schemeShawn Guo
This patch is to fix build breakage and support new relocation scheme for mx51evk. - Correct IRAM base address and add size definition The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision. - Include imx-regs.h in mx51evk.h Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to. - Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE They are used to define init RAM layout. - Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below 25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-22MX51: Add IPU driver for video supportStefano Babic
The patch is a porting of the IPU Linux driver developed by Freescale to have framebuffer functionalities in u-boot. The port is based on kernel 2.6.31 commit cc4fe714041805997b601fe8e5dd585d8a99297f, as delivered by Freescale [i.MX BSP]. Most features are dropped from the original driver and only LCD support is the goal of this porting. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-18MX5: rename mx51 to mx5Jason Liu
Rename mx51 to mx5 in order to support more mx51 like-style SOCs such as MX53 and the followings. Signed-off-by: Jason Liu <r64343@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-28 02:37:27 +0000