summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-mx6/imx-regs.h
AgeCommit message (Collapse)Author
2012-11-10mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololiteTroy Kisky
Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate. Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260. I don't have a sololite to verify. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-10-16mx6qsabreauto: Pass the board revision to the kernelFabio Estevam
The kernel from Freescale expects that the bootloader passes the board revision. Read the board revision and pass it via get_board_rev(). Without passing the board revision the kernel does not operate properly as the initialization of peripherals are different in revA versus revB boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15i.MX6: get rid of redundant struct src_regs (dupe of struct src)Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15i.MX6: define struct iomuxc and IOMUX_GPR2 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: Add ANATOP_PFD_480 bitfield constantsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15i.MX6: define IOMUX_GPR3 register bitfieldsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-09-01mxc: Define architecture identifierBenoît Thébaudeau
Define ARCH_MXC for i.MX devices. This is useful to identify features or behaviors common to all i.MX SoCs. The i.MX28 is omitted because its architecture is a bit different (like imx/mxc vs. mxs in Linux). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com>
2012-09-01MX: Set a common gpio.h for all i.MXStefano Babic
Each i.MX has its own gpio.h, defining the same structure. The internal GPIO controller has the same layout (at least for the register used by u-boot) and can be shared. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Matt Sealey <matt@genesi-usa.com>
2012-09-01imx-common/cmd_bmode.c: add imx bmode (bootmode) commandTroy Kisky
This is useful for forcing the ROM's usb downloader to activate upon a watchdog reset. Or, you can boot from either SD Card. Currently, support added for MX53 and MX6Q Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Note: MX53 support untested. Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-10mx6: Allow mx6 to access the IPUv3 registersFabio Estevam
Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15i.MX6: add enable_sata_clock()Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16imx: Remove unneeded/repititive definitions from imx headersVikram Narayanan
Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-04-16i.MX6: define CACHELINE_SIZEEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-03-27mx6: Read silicon revision from registerFabio Estevam
Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27mx6: Remove duplicate definition of ANATOP_BASE_ADDRFabio Estevam
Remove duplicate definition of ANATOP_BASE_ADDR. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-26usb/ehci: Add USB support for the MX6QWolfgang Grandegger
Currently, only USB Host 1 is supported. Cc: Remy Bohmer <linux@bohmer.net> Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-02-27net: fec_mxc: add 1000 Mbps selectionTroy Kisky
Define FEC_QUIRK_ENET_MAC and add to arch-mx6/imx-regs.h Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27mx6q: Add support for ECSPI through mxc_spi driverEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-27mx6q: define GPIO macros for translating between ordinals and port:indexEric Nelson
The interface to the mxc_gpio driver uses integer (ordinal) values to refer to all GPIOs on the i.MX processors. The registers themselves and much of the i.MX documentation are banked in groups of 32, and these macros allow the use of the port:index numbering for clarity. GPIO_NUMBER() converts to ordinal value from port:index GPIO_PORT() returns the port of an ordinal value GPIO_INDEX() returns the index or offset of the ordinal. Discussion on the mailing list at http://lists.denx.de/pipermail/u-boot/2012-January/116927.html Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-01-16imx: mx6q: add aipstz init for off platform periphJason Liu
Init peripheral access control register of AIPSTZ OPACRx: Buffer Writes(BW): 0 -> not bufferable, Supervisor Protect(SP): 0 -> not require supervisor privilege level for accesses. Write Protect(WP): 0 -> allows write accesses. Trusted Protect(TP): 0 -> allows unstrusted master Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de>
2012-01-16i.mx6:imx6q: allign MAC address with burned-in orderingJason Liu
For the i.mx6q, the burned-in MAC address will be the following odering, fuse: 0x620[7:0] MAC_ADDR[7:0] ---> mac[5] fuse: 0x620[15:8] MAC_ADDR[15:8] ---> mac[4] fuse: 0x620[23:16] MAC_ADDR[23:16] ---> mac[3] fuse: 0x620[31:24] MAC_ADDR[31:24] ---> mac[2] fuse: 0x630[7:0] MAC_ADDR[39:32] ---> mac[1] fuse: 0x630[15:8] MAC_ADDR[47:40] ---> mac[0] This patch also fix the error caculation for the fuse bank[0] address Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de>
2012-01-16net: imx: Add multi-FEC support for imx_get_mac_from_fuseFabio Estevam
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter. This feature is important on mx28 SoC for example that has two FEC ports. Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-12-09i.mx: add the initial support for freescale i.MX6Q processorJason Liu
i.MX6Q is freescale quad core processors with ARM cortex_a9 complex. This patch is to add the initial support for this processor. Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc:Stefano Babic <sbabic@denx.de>
generated by cgit (git 2.34.1) at 2025-01-07 11:12:38 +0000