summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm
AgeCommit message (Collapse)Author
2012-12-08Merge branch 'master' of git://git.denx.de/u-boot into masterStefano Babic
Conflicts: drivers/power/power_fsl.c include/configs/mx35pdk.h include/configs/mx53loco.h include/configs/woodburn_common.h board/woodburn/woodburn.c These boards still use the old old PMIC framework, so they do not merge properly after the power framework was merged into mainline. Fix all conflicts and update woodburn to use Power Framework. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-12-04mx28: Rename regs-power.h to regs-power-mx28.hMarek Vasut
The i.MX23 has different register layout and bit placement in the power supply. Thus, in order to be able to add support for MX23, rename the MX28's regs-power.h to regs-power-mx28.h . Moreover, add ifdef around inclusion of regs-*-mx28.h in imx-regs.h so the MX23 boards will include proper set of registers. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-12-04mx28: Remove SET, CLR, TOG ops from PLLxCTRL1 registersMarek Vasut
These registers don't have _SET, _CLR and _TOG at the respective offsets available, these registers has to be toggled via R-M-W if needed. Thus do not export these offsets anymore. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-11-27EXYNOS: mmc: support DesignWare Controller for Samsung-SoCJaehoon Chung
Support DesignWare MMC Controller for Samsung Specific. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-24mx28: Fix typo in POWER_DCLIMITS_NEGLIMIT_OFFSETMarek Vasut
The POWER_DCLIMITS_NEGLIMIT_OFFSET bit in mx28 power supply block is not called POWER_DCLIMITS_NETLIMIT_OFFSET, but POWER_DCLIMITS_NEGLIMIT_OFFSET. Correct the name in the header file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-24mx28: Fix typo in POWER_MINPWR_VBG_OFFMarek Vasut
The POWER_MINPWR_VBG_OFF bit in mx28 power supply block is not called POWER_MINPWR_FBG_OFF, but POWER_MINPWR_VBG_OFF. Correct the name in the header file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-20musb-new: omap2plus backend driverIlya Yanok
Backend driver for MUSB OTG controllers found on TI OMAP2/3/4 (tested only on OMAP3 Beagle). Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20OMAP3: am35x: add musb functionsIlya Yanok
AM35XX specific functions for integrated USB PHY/MUSB IP. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20OMAP3: am35x_def.h: add USB definesIlya Yanok
Add defines for MUSB IP block on AM35X SoCs. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20musb-new: am35x backend driverIlya Yanok
Backend driver for MUSB OTG controllers found on TI AM35x. It seems that on AM35X interrupt status registers can be updated _before_ core registers. As we don't use true interrupts in U-Boot and poll interrupt status registers instead this can result in interrupt handler being called with non-updated core registers. This confuses the code and result in hanged transfers. Add a small delay in am35x_interrupt as a workaround. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20am33xx: init OTG hardware and new musb gadget driverIlya Yanok
AM33xx has support for dual port MUSB OTG controller. This patch adds initialization for the controller using new MUSB gadget driver and ether gadget. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20musb-new: dsps backend driverIlya Yanok
Backend driver for MUSB OTG controllers found on TI AM33xx and TI81xx SoCs (tested with AM33xx only). Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-19mx5: Align SPI CS naming with i.MX53 reference manualFabio Estevam
Align SPI chip select naming with i.MX53 reference manual. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-11-16ehci-mxc: Add support for i.MX35Benoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16ehci-mxc: Define host offsetsBenoît Thébaudeau
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at SoC level. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-16mx31: Move EHCI definitions to ehci-fsl.hBenoît Thébaudeau
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to ehci-fsl.h so that all MXC SoCs can use them. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14mx51evk: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan
The inclusion of LCD patch into mx51evk breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-10arch-mx6: add mx6dl_pins.hTroy Kisky
Only the values used in the sabrelite board are added currently. Add more as other boards use them. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10imx-common: cpu: add imx_ddr_sizeTroy Kisky
Read memory setup registers to determine size of available ram. This routine works for mx53/mx6x I need this because when mx6solo called get_ram_size with a too large maximum size, the system hanged. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10mx6: soc: update get_cpu_rev and get_imx_type for mx6solo/sololiteTroy Kisky
Previously, the same value was returned for both mx6dl and mx6solo. Check number of processors to differeniate. Also, a freescale patch says that sololite has its cpu/rev stored at 0x280 instead of 0x260. I don't have a sololite to verify. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-11-10Merge git://git.denx.de/u-bootStefano Babic
2012-11-03Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-10-30arm bootm: Allow to pass board specified atagsPali Rohár
Board can implement function setup_board_tags which is used for adding atags Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
2012-10-29tegra: move to common SPL frameworkAllen Martin
Change tegra SPL to use common SPL framework. Any tegra specific initialization is now done in spl_board_init() instead of board_init_f()/board_init_r(). Only one SPL boot target is supported on tegra, which is boot to RAM image. jump_to_image_no_args() must be overridden on tegra so the host CPU can be initialized. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Tested-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-27Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD
2012-10-26arm: Remove support for NETARMMarek Vasut
This stuff has been rotting in the tree for a while now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for s3c4510Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for lpc2292Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26mx25: Place common functions into sys_proto.hFabio Estevam
imx-regs.h is meant to contain SoC register definitions. Common SoC funtions should go to sys_proto.h instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26MX35: add support for woodburn boardStefano Babic
The woodburn board is based on the MX35 SOC. Support for both external (NOR) and internal (SD Card) boot mode are added. It uses the generic SPL framework to implement the internal boot mode. The following peripherals are supported: - Ethernet (FEC) - SD Card - NAND (512 MB) - NOR Flash In the internal boot mode, a simple imximage header is generated to set the address in internal RAM where the SOC must copy the SPL code. The initial setup is then demanded to the SPL itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26MX35: Add soc_boot_mode and soc_boot_device to MX35Stefano Babic
The functions are required to use the generic SPL Framework. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26MX35: add LOW_LEVEL_SRAM_STACK to use SPL_FRAMEWORKStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-10-25am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbersPeter Korsgaard
So other parts can be added. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: support board specific ddr settingsPeter Korsgaard
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard
So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: Add SPI SPL as an optionTom Rini
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25VIDEO: add macro to set LCD size for DSS driverStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-10-25am335x: Enable RTC 32K OSC clockVaibhav Hiremath
In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19arm: Change global data baudrate to intSimon Glass
This does not need to be a long, so change it. Also adjust bi_baudrate to be unsigned. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-17mx5: lowlevel_init.S: Fix PLL settings for mx53Fabio Estevam
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz. Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz instead. Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI at 1080p because the IPU clock cannot reach the requested frequency. Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its maximum frequency. Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little bit to allow easier comparison with the original clock setup from FSL U-boot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mx25: Clean up imx-regs.hBenoît Thébaudeau
Clean up i.MX25 imx-regs.h: - Update mx31 imx-regs.h filename. - Test for __KERNEL_STRICT_NAMES just in case. - Define internal RAM size. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-16i.MX6: add HDMI transmitter register declarations from kernel WIP.Eric Nelson
Original source from Pengutronix HDMI driver work: http://git.pengutronix.de/?p=imx/linux-2.6.git;a=commitdiff;h=72c31cd67ac880bd90785af86f8e46f8ea7b3bb0 Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX6: set drive strength for parallel RGB padsEric Nelson
Default drive strength is disabled and won't function. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16i.MX: iomux: input pad array can be constEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-16mx6qsabreauto: Pass the board revision to the kernelFabio Estevam
The kernel from Freescale expects that the bootloader passes the board revision. Read the board revision and pass it via get_board_rev(). Without passing the board revision the kernel does not operate properly as the initialization of peripherals are different in revA versus revB boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16mx35: Fix eSDHC clocksBenoît Thébaudeau
Each eSDHC instance has a dedicated clock. gd->sdhc_clk must also be set accordingly. This is good for the case only a single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-16mx35: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx35 lowlevel_init: - Indent with tabs. - Fix comments. - Use defined values instead of literal constants. - Use defined macros instead of duplicating code. - Use macro parameters with default values instead of #define'd configs. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de>
2012-10-15mx25: Clean up lowlevel_initBenoît Thébaudeau
Clean up mx25 lowlevel_init: - Add comments. - Do not use write32 repeatedly with the same value in order not to increase code size. - Make register values configurable. - Use macro parameters with default values instead of literal constants. - Use defined macros instead of duplicating code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Matthias Weisser <weisserm@arcor.de>
generated by cgit (git 2.34.1) at 2025-01-10 08:16:04 +0000