| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
|
|
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Update fuse_bank0_regs structure according reference mannual.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
|
|
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
add reset controller status register
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
|
|
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
The SFR (special function registers) can be shared bwteen
sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adoptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This matrix header file can be shared between sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adaptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
|
|
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
This patch adds SPL support to the maxbcm MV78460 based board. Including
the fixed DDR configuratrion needed for the DDR training code. And the
the serdes PHY init code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array. Its type should be "int" rather
than "u32".
Use only the iterator "i" for the loop in do_pinmon().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
This dummy header was introduced by commit 630bf80ebb34 (ARM:
UniPhier: add dummy gpio.h to enable CONFIG_OF_CONTROL).
Thanks to commit a08d643dbd85 (dm: Drop gpio.h header from
fdtdec.c), such an ugly workaround is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
|
|
|
|
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for the A80 to the rsb code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
These functions are going away, so use the new uclass support instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions serve no useful purpose, and conflict with the generic API.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions are going away, so use the new uclass support instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.
This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.
The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
|
|
|
|
|
|
Add missing addresses to the list.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use full boot mode list in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they
do not support GPIO.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h>
to support OF_CONTROL for LS102x platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
|
|
|
|
PH1-sLD3, PH1-LD6b have DDR channel 2.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by <linux/sizes.h> for readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
The DDR PHY training function, ddrphy_prepare_training() would not
work if compiled with GCC 4.9.
The struct ddrphy (arch/arm/include/asm/arch-uniphier/ddrphy-regs.h)
is specified with __packed because it represents a hardware register
mapping, but it turned out to cause a problem on GCC 4.9.
If -mno-unaligned-access is specified (yes, it is in
arch/arm/cpu/armv7/config.mk), GCC 4.9 is aware of the
__attribute__((packed)) and generates extra instructions to perform
the memory access in a way that does not cause unaligned access.
(Actually it is not need here because the register base, the first
argument of the ddrphy_prepare_training(), is always given with a
4-byte aligned address.)
Anyway, as a result, readl() / writel() is divided into byte-wise
accesses. The problem is that this hardware only accepts 4-byte
register access. Byte-wise accesses lead to unexpected behavior.
There are some options to avoid this problem.
[1] Remove -mno-unaligned-access
[2] Add __aligned(4) along with __packed to struct ddrphy
[3] Remove __packed from struct ddrphy
[1] solves the problem for ARMv7, but it does not for pre-ARMv6 and
ARMv6-M architectures where -mno-unaligned-access is default.
So, [1] does not seem reasonable in terms of code portability.
Both [2] and [3] work well, but [2] seems too much. All the members
of struct ddrphy have the u32 type. No padding would be inserted
even if __packed is dropped.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.
As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:
http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html
Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
