summaryrefslogtreecommitdiff
path: root/arch/arm/include
AgeCommit message (Collapse)Author
2012-05-15i.MX2: Include asm/types.h in arch-mx25/imx-regs.hTimo Ketola
types.h must be included in imx-regs.h if one wants to include imx-regs.h in a board configuration file. That for one's part is necessary, if one wants to use addresses defined in imx-regs.h. For example, fsl_esdhc.c needs CONFIG_SYS_FSL_ESDHC_ADDR defined and a proper thing is to define it with IMX_MMC_SDHCx_BASE in board configuration file. This patch fixes the build in that case. Signed-off-by: Timo Ketola <timo@exertus.fi> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15i.MX25: esdhc: Add mxc_get_clock infrastructureTimo Ketola
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's implement get_clocks function. This is how it seems to be implemented elsewhere. Signed-off-by: Timo Ketola <timo@exertus.fi> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15i.MX6: add enable_sata_clock()Eric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15i.MX6: Add ANATOP regulator initDirk Behme
Init the core regulator voltage to 1.2V. This is required for the correct functioning of the GPU and when the ARM LDO is set to 1.225V. This is a workaround to fix some memory clock jitter. Note: This should be but can't be done in the DCD. The bootloader prevents access to the ANATOP registers. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Chen <b02280@freescale.com> CC: Jason Liu <r64343@freescale.com> CC: Ranjani Vaidyanathan <ra5478@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <festevam@gmail.com>
2012-05-15mx53loco: Allow to print CPU information at a later stageFabio Estevam
Print CPU information within board_late_init(). This is in preparation for adding 1GHz support, which requires programming a PMIC via I2C. As I2C is only available after relocation, print the CPU information later at board_late_init(), so that the CPU frequency can be printed correctly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15mx5: Add clock config interfaceFabio Estevam
mx5: Add clock config interface Add clock config interface support, so that we can configure CPU or DDR clock in the later init Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15imx-common: Factor out get_ahb_clk()Fabio Estevam
get_ahb_clk() is a common function between mx5 and mx6. Place it into imx-common directory. Cc: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX53: add function to set SATA clock to internalStefano Babic
The MX53 SATA interface can use an internal clock (USB PHY1) instead of an external clock. This is an undocumented feature, but used on most Freescale's evaluation boards, such as MX53-loco. As stated by Freescale's support: Fuses (but not pins) may be used to configure SATA clocks. Particularly the i.MX53 Fuse_Map contains the next information about configuring SATA clocks : SATA_ALT_REF_CLK[1:0] (offset 0x180C) '00' - 100MHz (External) '01' - 50MHz (External) '10' - 120MHz, internal (USB PHY) '11' - Reserved Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX5: Add definitions for SATA controllerStefano Babic
Add base address and MXC_SATA_CLK to return the clock used for the SATA controller. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15Define UART4 and UART5 base addressesStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15EXYNOS: support EXYNOS MIPI DSI interface driver.Donghwa Lee
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI based LCD Panel could be used with it. This patch supports MIPI-DSI driver based Samsung SoC chip. LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at board file and LCD panel driver specific function registered to mipi_dsim_ddi structure at lcd panel init function called system init. In the MIPI-DSI driver, find lcd panel driver by using registered lcd panel name, and then initialize lcd panel driver. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: support EXYNOS framebuffer and FIMD display drivers.Donghwa Lee
This patch support EXYNOS FB and FIMD display drivers. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: add LCD and MIPI DSI clock interface.Donghwa Lee
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: definitions of system resgister and power management registers.Donghwa Lee
This is definitions of system registers and power mananagement registers for EXYNOS SoC. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: Rename exynos5_tzpc structure to exynos_tzpcChander Kashyap
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic usase of tzpc. Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15OMAP3: pandora: pin mux updates for DM3730 board variantGrazvydas Ignotas
DM3730 needs some additional pin mux configuration for GPIOs 126-129 to work, add it. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15omap4+: Avoid using __attribute__ ((__packed__))Aneesh V
Avoid using __attribute__ ((__packed__)) unless it's absolutely necessary. "packed" will remove alignment requirements for the respective objects and may cause alignment issues unless alignment is also enforced using a pragma. Here, these packed attributes were causing alignment faults in Thumb build. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15arm: adapt asm/linkage.h from LinuxAneesh V
This will add ARM specific over-rides for the defines from linux/linkage.h Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15OMAP3+: reset: Create a common reset layer.SRICHARAN R
The reset.S has the function to do a warm reset on OMAP based socs. Moving this to a reset.c file so that this acts a common layer to add any reset related functionality for the future. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15omap5: pbias ldo9 turn onBalaji T K
Add omap5 pbias configuration for mmc1/sd lines and set voltage for sd data i/o lines Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15arm: omap5: correct boot device mode7 for eMMCBalaji T K
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP4/5: emif: Correct the emif power mgt shadow register bit fields.SRICHARAN R
PD_TIM bit field which specifies the power down timing is defined to occupy bits 8-11, where as it is actually from 12-15 bits. So correcting this. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: device: Add support to get the device type.SRICHARAN R
Add support to identify the device as GP/EMU/HS. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the sysctrl structure commonSRICHARAN R
Make the sysctrl structure common, so that it can be used in generic functions across socs. Also change the base address of the system control module, to include all the registers and not simply the io regs. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: SRAM: Change the SRAM base address.SRICHARAN R
The full internal SRAM of size 128kb is public in the case of OMAP5 soc. So change the base address accordingly. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4/5: Make the silicon revision variable common.SRICHARAN R
The different silicon revision variable names was defined for OMAP4 and OMAP5 socs. Making the variable common so that some code can be made generic. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: palmas: Configure nominal opp vdd valuesSRICHARAN R
The nominal opp vdd values as recommended for ES1.0 silicon is set for mpu, core, mm domains using palmas. Also used the right sequence to enable the vcores as per a previous patch from Nishant Menon, which can be dropped now. http://lists.denx.de/pipermail/u-boot/2012-March/119151.html Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.SRICHARAN R
The OMAP5 silicon has new DDR PHY design, which includes a external PHY as well. So configuring the ext PHY parameters here. Also the EMIF timimg registers and a couple of DDR mode registers needs to be updated based on the testing from the actual silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: io: Configure the io settings for omap5430 sevm board.SRICHARAN R
The control module provides options to set various signal integrity parameters like the output impedance, slew rate, load capacitance for different pad groups. Configure these as required for the omap5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: board: Add pinmux data for omap5_evm board.SRICHARAN R
Adding the full pinmux data for OMAP5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP5: clocks: Change clock settings as required for ES1.0 silicon.SRICHARAN R
Aligning all the clock related settings like the dpll frequencies, their respective clock outputs, etc to the ideal values recommended for OMAP5430 ES1.0 silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15OMAP4460: TPS Ensure SET1 is selected after voltage configurationNishanth Menon
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms. Currently we control this pin with a mux configuration as part of boot sequence. Current configuration results in the following voltage waveform: |---------------| (SET1 default 1.4V) | --------(programmed voltage) | <- (This switch happens on mux7,pullup) vdd_mpu(TPS) -----/ (OPP boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -----------------------/ (OPP boot voltage) Problem 1) |<----- Tx ------>| timing violation for a duration Tx close to few milliseconds. Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP. By using GPIO as recommended as standard procedure by TI, the sequence changes to: -------- (programmed voltage) vdd_mpu(TPS) ------------/ (Opp boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -------------/ (OPP boot voltage) NOTE: This does not attempt to address OMAP5 - Aneesh please confirm Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15OMAP3+: Introduce generic logic for OMAP voltage controllerNishanth Menon
OMAP Voltage controller is used to generically talk to PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code in multiple SoC code, introduce a common voltage controller logic which can be re-used from elsewhere. With this change, we replace setup_sri2c with omap_vc_init which has the same functionality, and replace the voltage scale replication in do_scale_vcore and do_scale_tps62361 with omap_vc_bypass_send_value. omap_vc_bypass_send_value can also now be used with any configuration of PMIC. NOTE: Voltage controller controlling I2C_SR is a write-only data path, so no register read operation can be implemented. Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit
Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-05-15serial: add LPC32X0 high-speed UART devices supportVladimir Zapolskiy
This change adds an implementation of high-speed UART found on NXP LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15arm926ejs: add NXP LPC32x0 cpu series supportVladimir Zapolskiy
This change adds initial support for NXP LPC32x0 SoC series. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-04-24i2c: Add support for designware i2c controllerVipin KUMAR
Earlier, a driver exists in the u-boot source for designware i2c interface. That driver was specific to spear platforms. This patch implements the i2c controller as a generic driver which can be used by multiple platforms The driver files are now renamed to designware_i2c.c and designware_i2c.h and these are moved into drivers/i2c folder for reusability by other platforms Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-16DMA: Split the APBH DMA init into block and channel initMarek Vasut
This fixes the issue where mxs_dma_init() was called either twice or never, without introducing any new init hooks. The idea is to allow each and every device using the APBH DMA block to configure and request only the channels it uses, instead of making it call init for all the channels as is now. The common DMA block init part, which only configures the block, is then called from CPUs arch_cpu_init() call. NOTE: This patch depends on: http://patchwork.ozlabs.org/patch/150957/ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16imx: Remove unneeded/repititive definitions from imx headersVikram Narayanan
Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-04-16i.MX6: define CACHELINE_SIZEEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
2012-03-29tegra: i2c: Add I2C driverYen Lin
Add basic i2c driver for Tegra2 with 8- and 16-bit address support. The driver requires CONFIG_OF_CONTROL to obtain its configuration from the device tree. (Simon Glass: sjg@chromium.org modified for upstream) Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: Enhance clock support to handle 16-bit clock divisorsSimon Glass
I2C ports have a 16-bit clock divisor. Add code to handle this special case so that I2C speeds below 150KHz are supported. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASESimon Glass
Change this name to fit with the current convention in the Tegra header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: usb: Add support for Tegra USB peripheralSimon Glass
This adds basic support for the Tegra2 USB controller. Board files should call board_usb_init() to set things up. Configuration is performed through the FDT, with aliases used to set the order of the ports, like this fragment: aliases { /* This defines the order of our USB ports */ usb0 = "/usb@0xc5008000"; usb1 = "/usb@0xc5000000"; }; drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29tegra: fdt: Add function to return peripheral/clock IDSimon Glass
A common requirement is to find the clock ID for a peripheral. This is the second cell of the 'clocks' property (the first being the phandle itself). Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-27EXYNOS: Add structure for Exynos4 DMCChander Kashyap
Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC). Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-03-27arm: Add Prep subcommand support to bootmSimon Schwarz
Adds prep subcommand to bootm implementation of ARM. When bootm is called with the subcommand prep the function stops right after ATAGS creation and before announce_and_cleanup. This is used in command "cmd_spl export" Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-03-27omap-common/spl: Add linux boot to SPLSimon Schwarz
This adds Linux booting to the SPL This depends on CONFIG_MACH_TYPE patch by Igor Grinberg (http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809) Related CONFIGs: CONFIG_SPL_OS_BOOT Activates/Deactivates the OS booting feature CONFIG_SPL_OS_BOOT_KEY defines the IO-pin number u-boot switch - if pressed u-boot is booted CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normaly RAM-begin + 0x100 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
2012-03-27devkit8000/spl: init GPMC for dm9000 in SPLSimon Schwarz
Linux crashes if the GPMC isn't configured for the dm9000. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
2012-03-27mx6: Read silicon revision from registerFabio Estevam
Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-01 08:11:04 +0000