| Age | Commit message (Collapse) | Author |
|---|
|
QSPI module output SCLK divisor value is configured through SCFG.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Peter Howard <phoward@gme.net.au>
|
|
|
|
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
This patch add support of LS1012A SoC along with
- Update platform & DDR clock read logic as per SVR
- Define MMDC controller register set.
- Update LUT base address for PCIe
- Avoid L3 platform cache compilation
- Update USB address, errata
- SerDes table
- Added CSU IDs for SDHC2, SAI-1 to SAI-4
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Makarand Pawagi <makarand.pawagi@mindspeed.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Other than LS1043A, LS1012A also Chassis Gen2 Architecture compliant.
So Avoid LS1043A specific defines in arch/arm
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Define specific macros for the voltage values for all voltage
domains for all applicable OPPs - OPP_NOM, OPP_OD and OPP_HIGH.
No separate macros are defined for VD_MPU and VD_CORE at OPP_OD
and OPP_HIGH as these use the same values as OPP_NOM.
The current macros will be used as common macros that can be
redefined appropriately based on a selected OPP configuration
at build time.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The current OPP_NOM voltage values defined for the MPU and CORE
voltage domains are based on the initial DRA75x_74x_SR1.1_DM data
manual. As per this DM, the PMIC boot voltage can be set to either
1.10V or 1.15V for VD_MPU, and either 1.06V or 1.15V for VD_CORE.
While the current values are correct, the latter set of values
are the values that are common across all DRA75x, DRA72x SoCs and
for all current Silicon revisions. So, update both the MPU and CORE
OPP_NOM voltages to 1.15V.
The macros are also slightly reorganized so that both the MPU and
CORE voltage domain values are defined together.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
DRA7xx has a 32KHz PHY clock for USB_PHY3 that must be enabled
for USB1 instance in Super-Speed.
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Import unified.h from Linux kernel 4.4.6 , commit
0d1912303e54ed1b2a371be0bba51c384dd57326 . This header file contains
macros used in libgcc functions in Linux kernel on ARM and will be
needed for the libgcc sync.
Since unified.h defines the W(instr) macro, we must drop this from
the macro from memcpy.S , otherwise this triggers a warning about
symbol redefinition. In order to keep the changes to unified.h to
the minimum, tweak arch/arm/lib/Makefile such that it defines the
CONFIG_ARM_ASM_UNIFIED macro, which places .syntax unified into all
of the assembler files. This is mandatory.
Moreover, for Thumb2 build, define CONFIG_THUMB2_KERNEL macro if and
only if Thumb2 build is enabled. This macro is checked by unified.h
and toggles between ARM and Thumb2 variant of the instructions in the
assembler source files.
Finally, this patch defines __LINUX_ARM_ARCH__=N macro based on the
new CONFIG_SYS_ARM_ARCH Kconfig option. This macro selects between
more optimal and more dense codepaths which work on armv5 and newer
and less optimal codepaths which work on armv4 and possible armv3m.
Tegra2 needs the same special handling as it does in arch/arm/Makefile
to cater for the arm720t boot core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This adds the bare minimum code to support Tegra186, with UART and eMMC
working.
The empty gpio.h is required because <asm/gpio.h> includes it. A future
cleanup round may be able to solve this for all Tegra generations at once.
mach-tegra/Makefile is adjusted not to compile anything for Tegra186, but
instead to defer everything to mach-tegra/tegra186/Makefile. This allows
the SoC code to pick-and-choose which of the C files in the "common"
mach-tegra/ directory to compile in based on the SoC's needs. Most of the
code is not valid for Tegra186, and this approach removes the need for
mach-tegra/Makefile to contain many SoC-specific ifdefs. This approach
may be applied to all other Tegra SoCs in a future cleanup round.
board186.c is introduced to replace board.c and board2.c. These files
currently contain a slew of SoC- and board-specific code that is not
valid for Tegra186. This approach avoids adding yet more ifdefs to those
files. A future cleanup round may refactor most of board*.c into board-/
SoC-specific functions files thus allowing the top-level functions like
board_init_early_f to be shared again.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Tegra186's MMC controller needs to be explicitly identified. Add another
compatible value for it.
Tegra186 will use an entirely different clock/reset control mechanism to
existing chips, and will use standard clock/reset APIs rather than the
existing Tegra-specific custom APIs. The driver support for that isn't
ready yet, so simply disable all clock/reset usage if compiling for
Tegra186. This must happen at compile time rather than run-time since the
custom APIs won't even be compiled in on Tegra186. In the long term, the
plan would be to convert the existing custom APIs to standard APIs and get
rid of the ifdefs completely.
The system's main eMMC will work without any clock/reset support, since
the firmware will have already initialized the controller in order to
load U-Boot. Hence the driver is useful even in this apparently crippled
state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
There are currently many places that define the list of all Tegra GPIOs;
the DT binding header and custom Tegra-specific header file gpio.h. Fix
the redundancy by replacing everything with the DT binding header file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.
Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Implement calls to secure monitor to read the MAC address from e-fuse.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
|
|
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add a psci_system_reset() which calls the SYSTEM_RESET function of
PSCI 0.2 and can be used by boards that support it to implement
reset_cpu().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add definitions for GRF_SOC_CON1 and GRF_SOC_CON3 which contain various
GMAC related fields.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Setup the clocks for the gmac ethernet interface. This assumes the mac
clock is fed by an external clock which is common on RK3288 based
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The current SPL header, created by the 'mksunxiboot' tool, has size
32 bytes. But the code in the boot ROM stores the information about
the boot media at the offset 0x28 before passing control to the SPL.
For example, when booting from the SD card, the magic number written
by the boot ROM is 0. And when booting from the SPI flash, the magic
number is 3. NAND and eMMC probably have their own special magic
numbers too.
Currently the corrupted byte is a part of one of the instructions in
the reset vectors table:
b reset
ldr pc, _undefined_instruction
ldr pc, _software_interrupt <- Corruption happens here
ldr pc, _prefetch_abort
ldr pc, _data_abort
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
In practice this does not cause any visible problems, but it's still
better to fix it. As a bonus, the reported boot media type can be
later used in the 'spl_boot_device' function, but this is out of
the scope of this patch.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
drivers/net/zynq_gem.c
|
|
Add platforms specific phy mode configuration bits to be used
to configure phy mode in control module.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Freescale PPC SoCs do not hard-code security engine's Job Ring 0
address, rather a define is used. This patch adds the same
functionality to the ARM based SoCs (i.e. LS1/LS2 and i.MX parts)
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Several UART input selects are missing. The fourth input select
for UART2_TX_DATA_ALT0 is actually also missing in the documentation.
(at least in Rev. B of the i.MX 7Dual Reference Manual). However,
when looking at the tables of other input selects, it is very natural
that there must be an input select for the UART2_TX_DATA_ALT0 pad.
The Colibri iMX7 also uses that pad for UART2 RX (in DTE mode), and
it was required to set that particular input select register to get a
working UART2.
|
|
This patch adds the IOMUX setting for using SD1_DAT5 as GPIO5:9.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
|
|
Commit bfb33f0bc45b ("sunxi: mctl_mem_matches: Add missing memory
barrier") broke compilation for the Pine64, as dram_helper.c now
includes <asm/armv7.h>, which does not compile on arm64.
Fix this by moving all barrier instructions into a separate header
file, which can easily be shared between arm and arm64.
Also extend the inline assembly to take the "sy" argument, which is
optional for ARMv7, but mandatory for v8.
This fixes compilation for 64-bit sunxi boards (Pine64).
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
In current Linux kernel Tegra DT files, 64-bit addresses are represented
in unit addresses as a pair of comma-separated 32-bit values. Apparently
this is no longer the correct representation for simple busses, and the
unit address should be represented as a single 64-bit value. If this is
changed in the DTs, arm/arm/mach-tegra/board2.c:ft_system_setup() will no
longer be able to find and enable the GPU node, since it looks up the node
by name.
Fix that function to enable nodes based on their compatible value rather
than their node name. This will work no matter what the node name is, i.e
for DTs both before and after any rename operation.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
