| Age | Commit message (Collapse) | Author |
|---|
|
|
|
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for the A80 to the rsb code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
These functions are going away, so use the new uclass support instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions serve no useful purpose, and conflict with the generic API.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions are going away, so use the new uclass support instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
Add missing addresses to the list.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use full boot mode list in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they
do not support GPIO.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h>
to support OF_CONTROL for LS102x platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
|
|
|
|
PH1-sLD3, PH1-LD6b have DDR channel 2.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by <linux/sizes.h> for readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
The DDR PHY training function, ddrphy_prepare_training() would not
work if compiled with GCC 4.9.
The struct ddrphy (arch/arm/include/asm/arch-uniphier/ddrphy-regs.h)
is specified with __packed because it represents a hardware register
mapping, but it turned out to cause a problem on GCC 4.9.
If -mno-unaligned-access is specified (yes, it is in
arch/arm/cpu/armv7/config.mk), GCC 4.9 is aware of the
__attribute__((packed)) and generates extra instructions to perform
the memory access in a way that does not cause unaligned access.
(Actually it is not need here because the register base, the first
argument of the ddrphy_prepare_training(), is always given with a
4-byte aligned address.)
Anyway, as a result, readl() / writel() is divided into byte-wise
accesses. The problem is that this hardware only accepts 4-byte
register access. Byte-wise accesses lead to unexpected behavior.
There are some options to avoid this problem.
[1] Remove -mno-unaligned-access
[2] Add __aligned(4) along with __packed to struct ddrphy
[3] Remove __packed from struct ddrphy
[1] solves the problem for ARMv7, but it does not for pre-ARMv6 and
ARMv6-M architectures where -mno-unaligned-access is default.
So, [1] does not seem reasonable in terms of code portability.
Both [2] and [3] work well, but [2] seems too much. All the members
of struct ddrphy have the u32 type. No padding would be inserted
even if __packed is dropped.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.
As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:
http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html
Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The clocks on the A80 are hooked up slightly different, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a headerfile with the sun9i ccu register layout.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a headerfile with all the base addresses from the sun9i blocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
sun4i - sun8i have (aprox.) the same iomem layout, but sun9i is quite
different, so add a wrapper cpu.h which includes the right mach specific
cpu_sun#i.h based on mach, like we already do with clock.h and dram.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Which pll-s are available depends on the machine type, move the
clock_get_pllX / clock_set_pllX prototypes to the clock_sun?i.h header files
so that we only declare what is actually available. e.g. clock_get_pll5p()
is not available on sun6i / sun8i, and with sun9i we get a completely
different set of plls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
phys_addr_t is designed for physical addresses that's why
use it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This adds Renesas rmobile ARM SoC's SD/MMC host support.
This drivers tested with Gose board and Koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
The SAMA5D4 has the same usb platform data with SAMA5D3 SoC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for lvds lcd panels
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Move a few mux defines around so that all the mux defines are properly sorted
by port number.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.
With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.
With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.
*) "unknown" is the actual name of this register in the android kernel sources
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.
Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.
A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
