summaryrefslogtreecommitdiff
path: root/arch/arm/include
AgeCommit message (Collapse)Author
2014-02-06ARM: IXP: Remove the IXP architecture supportMarek Vasut
The architecture is unmaintained and dead, remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-01-29Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-24spl: common: Support for USB MSD FAT image loadingDan Murphy
Add SPL support to be able to detect a USB Mass Storage device connected to a USB host. Once a USB Mass storage device is detected the SPL will load the u-boot.img from a FAT partition to target address. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2014-01-24DRA7: add ABB setup for MPU voltage domainNishanth Menon
Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24DRA7: Add support for ES1.1 silicon ID codeNishanth Menon
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support for ES1.1 IDCODE change. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24ARM: AM335x: Enable DDR dynamic IO power downSatyanarayana, Sandhya
This patch enables dynamically powering down the IO receiver when not performing a read on boards using DDR3. This optimizes both active and standby power consumption. This bit is not set on EVM SK and EVM 1.5 and later boards. Setting the same. This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
2014-01-24ARM: OMAP3: Rename OMAP3_PUBLIC_SRAM_* to NON_SECURE_SRAM_*Enric Balletbò i Serra
Other TI processors like am33xx, omap4 and omap5 have called these variables as NON_SECURE_SRAM_*, shouldn't be a big problem rename these variables to be coherent. One reason more to rename these variables is to have the possibility of any OMAP3 board to use the ti_armv7_common.h include as the NON_SECURE_SRAM_END is used to define the CONFIG_SYS_INIT_SP_ADDR variable. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2014-01-24ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar
The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24ARM: OMAP4/5: Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALLJassi Brar
The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-20ARM: rpi_b: power on SDHCI and USB HW modulesStephen Warren
Send RPC commands to the VideoCore to turn on the SDHCI and USB modules. For SDHCI this isn't needed in practice, since the firmware already turned on the power in order to load U-Boot. However, it's best to be explicit. For USB, this is necessary, since the module isn't powered otherwise. This will allow the kernel USB driver to work. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-01-20Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-01-17mx6: Revert "mx6: soc: Disable VDDPU regulator"Fabio Estevam
Commit 022298278 (mx6: soc: Disable VDDPU regulator) is causing kernel hang for people using FSL kernel 3.0.35 and 3.10, so revert it for now. Reported-by: Otavio Salvador <otavio@ossystems.com.br> Reported-by: Pierre Aubert <p.aubert@staubli.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-16Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-01-16arm: rmobile: Add SH QSPI base register addressNobuhiro Iwamatsu
This adds base register address of SH QSPI. Currently, SH QSPI is used only from R8A7790 and R8A7791. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-15Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-15mx6: Add initial support for the Hummingboard soloFabio Estevam
SolidRun has designed the Hummingboard board based on mx6q/dl/solo. Add the initial support for the mx6 solo variant. More information about this hardware can be found at: http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware (Carrier-One was the previous name of Hummingboard). Based on the work from Jon Nettleton <jon.nettleton@gmail.com>. Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-15mx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()Fabio Estevam
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency that will be generated. No changes are made to mx6slevk, which uses the default 50MHz fec clock. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-13usb: ehci: exynos: set/reset hsic physInderpal Singh
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2 are for HSIC phys. The usb 2.0 phy is already being setup. This patch sets up the hsic phys. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2014-01-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be added to include/configs/exynos5-dt.h now. Conflicts: include/configs/exynos5250-dt.h Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10gpio: zynq: Add dummy gpio routinesJagannadha Sutradharudu Teki
GPIO dummy routines are required for fdt build, may be removed these dependencies once the u-boot fdt is fully optimized. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Add support to find bootmodeJagannadha Sutradharudu Teki
Added support to find the bootmodes by reading slcr bootmode register. this can be helpful to autoboot the configurations w.r.t a specified bootmode. Added this functionality on board_late_init as it's not needed for normal initializtion part. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10armv8: Use __aarch64__ rather than CONFIG_ARM64 in some casesTom Rini
The toolchain sets __aarch64__ for both LE and BE. In the case of posix_types.h we cannot reliably use config.h as that will lead to problems. In the case of byteorder.h it's clearer to check the EB flag being set in either case instead. Cc: David Feng <fenghua@phytium.com.cn> Signed-off-by: Tom Rini <trini@ti.com> Amended by Albert ARIBAUD <albert.u.boot@aribaud.net> to actually remove the config.h include from the posix_types.h files, with permission from Tom Rini.
2014-01-09arm64: core supportDavid Feng
Relocation code based on a patch by Scott Wood, which is: Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-01-09socfpga/dwmmc: Adding DesignWare MMC driver support for SOCFPGAChin Liang See
To add the DesignWare MMC driver support for Altera SOCFPGA. It required information such as clocks and bus width from platform specific files (SOCFPGA handoff files) Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-06Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-06Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: include/micrel.h The conflict above was trivial, caused by four lines being added in both branches with different whitepace.
2014-01-03arm: mx5: Add fuse supply enable in fsl_iimSergey Alyoshin
Enable fuse supply before fuse programming and disable after. Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2014-01-03imx: Easy enabling of SION per-pin using MUX_MODE_SION helper macroOtavio Salvador
The macro allows easy setting in per-pin, as for example: ,---- | imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_MODE_SION); `---- The IOMUX_CONFIG_SION allows for reading PAD value from PSR register. The following quote from the datasheet: ,---- | ... | 28.4.2.2 GPIO Write Mode | The programming sequence for driving output signals should be as follows: | 1. Configure IOMUX to select GPIO mode (Via IOMUXC), also enable SION if need | to read loopback pad value through PSR | 2. Configure GPIO direction register to output (GPIO_GDIR[GDIR] set to 1b). | 3. Write value to data register (GPIO_DR). | ... `---- This fixes the gpio_get_value to properly work when a GPIO is set for output and has no conflicts. Thanks for Benoît Thébaudeau <benoit.thebaudeau@advansee.com>, Fabio Estevam <fabio.estevam@freescale.com> and Eric Bénard <eric@eukrea.com> for helping to properly trace this down. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-02mx6: soc: Disable VDDPU regulatorFabio Estevam
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator in order to save power. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02mx6: soc: Staticize set_vddsoc()Fabio Estevam
set_vddsoc() is not used anywhere else, so make it static. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-12-30Exynos5420: Add support for 5420 in pinmux and gpioRajeshwari Birje
Adds code in pinmux and gpio framework to support Exynos5420. Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30Exynos5420: Add DDR3 initialization for 5420Rajeshwari Birje
This patch intends to add DDR3 initialization code for Exynos5420. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30Exynos5420: Add clock initialization for 5420Rajeshwari Birje
This patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420 Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30EXYNOS5420: Add dmc and phy_control register structureRajeshwari Birje
Add dmc and phy_control register structure for 5420. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30EXYNOS5420: Add power register structure.Rajeshwari Birje
Add structure for power register for Exynos5420 Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30Exynos5420: Add base addresses for 5420Rajeshwari Birje
Adds base addresses of various IPs and controllers required for Exynos5420. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30EXYNOS5: Create a common board fileRajeshwari Birje
Create a common board.c file for all functions which are common across all EXYNOS5 platforms. exynos_init function is provided for platform specific code. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-18ARM: AM43xx: GP_EVM: Add support for DDR3Lokesh Vutla
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH). Adding details for the same. Below is the brief description of DDR3 init sequence(SW leveling): -> Enable VTT regulator -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program leveling registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: EPOS_EVM: Add support for LPDDR2Lokesh Vutla
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A) Adding LPDDR2 init sequence and register details for the same. Below is the brief description of LPDDR2 init sequence: -> Configure VTP -> Configure DDR IO settings -> Disable initialization and refreshes until EMIF registers are programmed. -> Program Timing registers -> Program PHY control and Temp alert and ZQ config registers. -> Enable initialization and refreshes and configure SDRAM CONFIG register -> Wait till initialization is complete and the configure MR registers. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: clocks: Update DPLL detailsLokesh Vutla
Updating the Multiplier and Dividers value for all DPLLs. Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value returned the MPU DPLL is locked. At different OPPs follwoing are the MPU locked frequencies. OPP50 300MHz OPP100 600MHz OPP120 720MHz OPPTB 800MHz OPPNT 1000MHz According to the latest DM following is the OPP table dependencies: VDD_CORE VDD_MPU OPP50 OPP50 OPP50 OPP100 OPP100 OPP50 OPP100 OPP100 OPP100 OPP120 So at different OPPs of MPU it is safest to lock CORE at OPP_NOM. Following are the DPLL locking frequencies at OPP NOM: Core locks at 1000MHz Per locks at 960MHz LPDDR2 locks at 266MHz DDR3 locks at 400MHz Touching AM33xx files also to get DPLL values specific to board but no functionality difference. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: mux: Update mux dataLokesh Vutla
Updating the mux data for UART, adding data for i2c0 and mmc. And also updating pad_signals structure. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Update Current Booting devices listLokesh Vutla
Current Booting devices list is different from that of AM33xx. Updating the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43XX: board: add support for reading onboard EEPROMSekhar Nori
Add support for reading onboard EEPROM to enable board detection. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Adapt to ti_armv7_common.h config fileLokesh Vutla
Use ti_armv7_common.h config file to inclde the common configs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18ARM: AM43xx: Update the base addresses of modulesLokesh Vutla
PRCM, timer base addresses and offsets are different from AM33xx. Updating the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18arm: tegra: Fix the CPU complex reset masksAlban Bedel
The CPU complex reset masks are not matching with the datasheet for the CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET/CLR_0 registers. For both T20 and T30 the register consist of groups of 4 bits, with one bit for each CPU core. On T20 the 2 high bits of each group are always stubbed as there is only 2 cores. Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swrren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18ARM: tegra: support SKU b1 of Tegra30Alban Bedel
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips. Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-17nitrogen6x: Move setup_sata to common partGiuseppe Pagano
Move setup_sata function definition from platform file nitrogen6x.c to arch/arm/imx-common/sata.c to avoid code duplication. Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Eric Nelson <eric.nelson@boundarydevices.com>
2013-12-17i.MX6 (DQ/DLS): use macros for mux and pad declarationsEric Nelson
This allows the use of either or both declarations from the files mx6q_pins.h and mx6dl_pins.h. All board files should include <asm/arch/mx6-pins.h> with one of the following defined in boards.cfg MX6Q - for boards targeting i.MX6Q or i.MX6D MX6DL - for boards targeting i.MX6DL MX6S - for boards targeting i.MX6S MX6QDL - for boards that support any of the above with run-time detection Pad declarations will be MX6_PAD_x for single-variant boards and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both processor classes. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-12-12arm: am437: Fix offset for USB registersDan Murphy
Fix the offset for the USB clock registers Signed-off-by: Dan Murphy <dmurphy@ti.com>
generated by cgit (git 2.34.1) at 2024-12-29 09:21:25 +0000